2 intermediate shaft assembly with the bolt. ... AND WASHER SWITCH AND SPIRAL CABLE ... (c) Push into the light control switch and headlight dimmer switch ...
INSTALL NO. 2 INTERMEDIATE SHAFT ASSEMBLY Align the matchmarks on the No. 2 intermediate shaft assembly and main shaft assembly. (b) Install the No. 2 intermediate shaft assembly with the bolt. Torque: 28 N·m (290 kgf·cm, 21 ft·lbf) 2. INSTALL SLIDING YOKE Temporarily install the sliding yoke to the No. 2 intermediate shaft assembly with the bolt A. 3. INSTALL STEERING COLUMN ASSEMBLY (a) Install the steering column assembly with the lower mount bolt and 2 upper mount bolts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf) (b) Connect the connectors.
4. (a)
Matchmarks A B
F08008
CONNECT SLIDING YOKE Align the matchmarks on the sliding yoke and No. 3 intermediate shaft assembly. (b) Install the bolt B. Torque: 28 N·m (290 kgf·cm, 21 ft·lbf) (c) Torque the bolt A. Torque: 28 N·m (290 kgf·cm, 21 ft·lbf) 5. INSTALL NO. 2 COLUMN HOLE COVER Install the No. 2 column hole cover with the clip. 6. A/T: INSTALL KEY INTERLOCK CABLE (See page AX-24 ) 7. INSTALL COLUMN UPPER COVER, LIGHT CONTROL SWITCH AND HEADLIGHT DIMMER SWITCH, WIPER AND WASHER SWITCH AND SPIRAL CABLE (a) Install the column upper cover.
(b)
Slide the column upper cover and install the spiral cable.
F09906
2002 ECHO (RM884U)
Author:
Date:
1080
SR-21 STEERING
-
TILT STEERING COLUMN
(c)
F09908
Marks F08459
Torx Screw
Screw Case
Push into the light control switch and headlight dimmer switch until the claw is latched. (d) Employ the same manner described above to the wiper and washer switch. (e) Connect the airbag connector to the spiral cable. (f) Connect the 3 connectors to the spiral cable, light control switch and headlight dimmer switch and wiper and washer switch. 8. INSTALL COLUMN LOWER COVER Install the column lower cover with the 3 screws. 9. CENTER SPIRAL CABLE (a) Check that the front wheels are facing straight ahead. (b) Turn the cable counterclockwise by hand until it becomes harder to turn. (c) Then rotate the cable clockwise about 2.5 turns to align the marks. HINT: The cable will rotate about 2.5 turns to either left or right of the center. 10. INSTALL STEERING WHEEL (a) Align the matchmarks on the steering wheel and main shaft assembly. (b) Install the steering wheel set nut. Torque: 50 N·m (510 kgf·cm, 37 ft·lbf) 11. INSTALL STEERING WHEEL PAD NOTICE: Never use airbag parts from another vehicle. When replacing parts, replace with new ones. Make sure the wheel pad is installed with the specified torque. If the wheel pad has been dropped, or there are cracks, dents or other defects in the case or connector, replace the wheel pad with a new one. When installing the wheel pad, take care that the wirings do not interfere with other parts and that they are not pinched between other parts. (a) Connect the connector. (b) Connect the airbag connector.
(c)
(d) 12.
Install the steering wheel pad after confirming that the circumference groove of the torx screws is caught on the screw case. Using a torx socket wrench, torque the 2 screws. Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf) CHECK STEERING WHEEL CENTER POINT
Silhouette® and Nantucket⢠window shadings are made of 100% polyester, which means they are inherently durable and resilient. However, care must be taken to avoid wrinkling the fabric, particularly where the vanes meet the facings. The Palette® F
Allumez toujours la hotte lorsque vous cuisinez à haute température ou que vous faites f amber des aliments. c. Nettoyez fréquemment les ventilateurs de la ...
Si el frente de su ducha es removible, lÃmpiela periódicamente removiendo el frente destornillando el tornillo central. Si votre douche est munie d'une façade ...
Installation Steps: 1. The stub-out pipe for installation must be 5/8'' (+/- 1/8'') measured from the finished wall surface. Apply plumber's tape (included) to the pipe ...
materials, will fully satisfy your requirements. This new appliance is very ..... This circuit-breaker should be sized in compliance with local installation regulations.
3¼" x 10", Roof jack and shutter. N/A. 6. 5. 6. 10. NOTE: These commonly used installation parts can be purchased at a local hardware store. Thermador does ...
Check with the local plumbing code requirements before installation. This product is recommended to be ... Antes de la instalación, consulte las exigencias del código local de plomerÃa. El producto se recomienda de ser ... llave hexagonal. Retirer
and standards, including fire-rated construction codes and standards. 4. Sufficient air is needed for proper combustion and exhausting of gases through the flue ...
Retirez les quatre écrous encastrables en nylon de 1/4 po des poteaux du ventilateur et retirez la plaque coulissante. Tournez le ventilateur de. 90 degrés vers ...
For Lazer, Halo Miniature and circuit #1 of. Haloâ2 , track contact must be in clown posi- tion (Fig A). For Halo-2 Circuit #2, move con- tact to the up position (Fig.
If LP, the LP cylinder must be unhooked and stored outside in a well ... is not intended to be installed in or on recreational vehicles, trailers and/or boats. Note:.
and the American Society for Heating, Refrigeration and Air Conditioning ..... nationale de la Protection contre les Incendies (nePa) et par les Ingénieurs de ... et de l'air Climatisé (asHrae) et par les autorités responsables des codes locaux. ....
property damage, personal injury or death. ○ Do not ..... opening a window or by increasing the power of the mechanical exhaust system if installed. WARNING ...
Do not touch any electrical switch; do not use any .... exhaust dryer into a chimney, a wall, a ceiling, an attic, ...... (mise à la terre) pour assurer votre protection.
2 Filtres à tamis métalliques. 2 Ampoules halogènes (préinstallées). 1 Collier de transition circulaire de 7". 1 Collier de transition rectangulaire de 3 1/4" x 10" ...
To reset: With hood off, hold the Button for three seconds, after three seconds the Graphic ... hood body near the wiring diagram that indicates the blower CFM. ... (the âProductsâ) that such Products will be free from defects in materials or wor