HP_PrepKing_HP2-Z18_v2011-06-15_95q_By-Jhon Number: HP2-Z18 Passing Score: 800 Time Limit: 120 min File Version: 2011-06-15 Exam Code: HP2-Z18 Version: 2011-06-15 Questions: 95 We are including latest study material. Thanks By Jhon
Exam A QUESTION 1 Which HP E-Series switch models display the following prompt in the interface configuration context? (Select two) HP Switch (eth-A24)# A. B. C. D. E.
E8212zl E6600-24G E5412-96GZI E2910-24Gal E350CM8G-POEyI
Answer: AC Section: (none) Explanation/Reference:
QUESTION 2 When Spanning Tree Protocol is enabled, which devices receive outbound LLDP advertisements from an HP E-Series switch? A. B. C. D. E.
those with interfaces in VLAN 1 those that receive the switch's broadcasts those that are directly connected to the switch those in the LLDP multicast group those not blocked by Spanning Tree Protocol
Answer: C Section: (none) Explanation/Reference:
QUESTION 3 You must assign a friendly name to port B24 on an HP E5406 zI switch. Given the following prompt, which command must you enter next to complete this task? E5406# A. B. C. D.
configure name int b24 interface b2 4 manager
Answer: A Section: (none) Explanation/Reference:
QUESTION 4 You are at the manager level prompt In the CLI of an HP E3500 yI switch. Which options are available at
this prompt? (Select two) A. B. C. D. E.
assign IP address to VLAN interface enable IP routing restart the switch disable ports update software
Answer: CE Section: (none) Explanation/Reference:
QUESTION 5 Which statements are true about the primary and secondary flash areas of an HP E-Series switch? (Select two) A. The primary area contains the switch's operating system, which is automatically copied to the secondary area whenever the switch is restarted. B. The switch can be started using the software stored in either area. C. The software stored in the primary area is always used to start the switch. D. The primary area always contains the most recent software version; the secondary area contains an earlier version to be used if the primary version. E. The software in each area is stored and managed independently Answer: BE Section: (none) Explanation/Reference:
QUESTION 6 You make configuration changes to the running configuration of your HP E3500 yI switch. Which command saves these changes to your startup configuration? A. B. C. D.
save running-config copy running-config startup-config write memory write config
Answer: C Section: (none) Explanation/Reference:
QUESTION 7 Port B1 on an HP ProCurve 5406zI switch is an untagged member of VLAN 155 and not a tagged member of any VLAN PortC1is a tagged member of VLAN 155 and an untagged member of VLAN 100. You issue the following command: 5406zl (config)# no vlan 155 Why do you receive the following prompt?
The following ports will be moved to the default VLAN: B1 Do you want to continue? [y/n]: A. B. C. D.
The CLI always issues this prompt when deleting a VLAN The CLI will not allow you to orphan a port The CLI will not delete a VLAN with any port membership. All ports must be moved to the default VLAN before you can delete the VLAN.
Answer: B Section: (none) Explanation/Reference:
QUESTION 8 Refer to the exhibit below.
You enter the following command at the switch's CLI: E5406 (vlan-100) # no untag a24 Why does this command fail? A. B. C. D.
PortA24 is not a member of VLAN 100. Port A24 must be a member of at least one VLAN VLAN 100 must have at least one port member no untag a24 is an invalid CLI command
Answer: B Section: (none) Explanation/Reference:
QUESTION 9 At the CLI of an HP E2610-24 switch, you have assigned ports 1-4 to VLAN 50 as untagged members. The E2610 is connected through port 24 to an E5406 zl switch. All other configuration parameters on the E2610 are at default settings.
The E5406 is configured with a VLAN 50 IP address of 192.168.50.1/24. IP routing is enabled. It is connected to the E2610 through port B24, which is a tagged member of VLAN 50 On the E2610, which command will enable the E5406 to act as a default gateway for VLAN 50 clients? A. B. C. D.
E2610 (config) # vlan 50 ip address 192.168.50.2/24 E2610 (config) # ip default-gateway 192.168.50.1 E2610 (config) # ip route 192.168.50.0/24 vlan 50 E2610 (config) # vlan 50 tag 24
Answer: A Section: (none) Explanation/Reference:
QUESTION 10 What is the effect of the following command entered at the CLI of an HP E3500 yI switch? E3500 (config) # timesync sntp A. B. C. D.
The switch will use SNTP as its time synchronization protocol The switch will provide SNTP services to all connected VLANs. The switch's clock will be synchronized with a configured SNTP server. The switch will broadcast for an SNTP server.
Answer: A Section: (none) Explanation/Reference:
QUESTION 11 Which security technology requires that you set read/write community names? A. B. C. D. E.
SFTP SSH SNMP HTTPS SMTP
Answer: C Section: (none) Explanation/Reference:
QUESTION 12 You must enable Secure HTTP (HTTPS) to encrypt web-based management traffic on an HP E- Series switch. The switch is at default settings. What must be installed or enabled to apply this solution? A. web server B. encryption accelerator C. digital certificate
D. internal RADIUS server Answer: AC Section: (none) Explanation/Reference:
QUESTION 13 Which remote management interface on an E-Series switch can be secured by enabling Secure Sockets Layer (SSL)? A. B. C. D.
console menu web management Telnet
Answer: C Section: (none) Explanation/Reference:
QUESTION 14 What are benefits of implementing Secure Socket Shell (SSH) for remote management of HP switches? (Select two) A. B. C. D. E. F.
user accounting encryption of management traffic stronger passwords enforcement of management VLAN secure authentication encryption of all traffic
Answer: BE Section: (none) Explanation/Reference:
QUESTION 15 Ports 1-4 on an HP E3500 yI switch are tagged members of VLAN 44 and untagged members of VLAN 45. What is the effect of the following command? E3500 (config)# trunk. 1-4 trk3 lacp A. B. C. D.
trk3 becomes a tagged member of VLAN 44 and an untagged member of VLAN 45 trk3 will have no VLAN memberships until they are configured by an administrator trk3 becomes an untagged member of VLAN 1 and has no other VLAN memberships trk3 becomes an untagged member of VLAN 1 and a tagged member of VLAN 44
Answer: C Section: (none) Explanation/Reference:
QUESTION 16 You must configure link aggregation on an HP E-Series switch with standby links to provide for link redundancy. Which technology is required for this configuration? A. B. C. D.
static LACP HP port trunking dynamic LACP distributed trunking
Answer: C Section: (none) Explanation/Reference:
QUESTION 17 What is the default Spanning Tree Bridge Priority on an HP E3500 yI switch? A. B. C. D.
0 1024 4096 32768
Answer: D Section: (none) Explanation/Reference:
QUESTION 18 Which bridge selling ensures that a particular switch will be elected Root Bridge of an MST instance, assuming all Spanning Tree settings on other switches are at the default? A. B. C. D.
CIST Bridge Priority set to 0 CISTBridgePriorilytoset15 Bridge Priority for the instance set to 0 Bridge Priority for the instance set to 15
Answer: C Section: (none) Explanation/Reference:
QUESTION 19 The output of show spanning-tree instance 3 on two HP E8212 zI Switches indicates that both switches are the Root of MST instance 3. What is an accurate explanation for this output? A. The switches have the same MST configuration name B. The switches are running incompatible Spanning Tree Protocols. C. The switches are configured with the same Bridge Priority for the instance.
D. The switches have different MST configuration revisions. Answer: D Section: (none) Explanation/Reference:
QUESTION 20 Which command is used to show all VLANs not assigned to user-defined MST instances? A. B. C. D.
E5406(config)# show spanning-tree instance all E54061(config)# show spanning-tree instance ist E5406(config)# show spanning-tree instance cst E5406(config)# show spanning-tree instance vlans
Answer: B Section: (none) Explanation/Reference:
QUESTION 21 What is the default version Spanning Tree Protocol on E5406 zI switch? A. B. C. D.
STP MSTP RSTP PVST
Answer: B Section: (none) Explanation/Reference:
QUESTION 22 You must design and configure a Spanning Tree solution using HP E-Series switches. Why is it necessary to ensure that all VLANs defined on the switches are carried on all switch-to-switch links? A. B. C. D.
to ensure all switches can exchange BPDUs when ports are in blocking state to ensure all switches can locate a Root Port to ensure all VLANs have redundant paths to the Root Bridge to ensure all VLANs are part of the Internal Spanning Tree (IST)
Answer: C Section: (none) Explanation/Reference:
QUESTION 23 Which categories of routing protocols include RIP and OSPF? (Select two.)
A. B. C. D. E.
exterior gateway link state label switching distance vector interior gateway
Answer: BD Section: (none) Explanation/Reference:
QUESTION 24 What is the effect of the following commands entered at the CLI of an HP E8212 zI switch with routing and RIP enabled? E8212 (rip)# redistribute ospf A. B. C. D.
The switch will filter OSPF routes from RIP updates received from peers, The switch will include routes learned through OSPF in all RIP updates. The switch will include routes learned through RIP in all OSPF link-state messages. The switch will give preference to OSPF routes over RIP routes in its route table.
Answer: B Section: (none) Explanation/Reference:
QUESTION 25 You have enabled RIPv2 with the following command at the CLI of an HP E3500 yI switch: E3500 (config) # router rip E3500 (rip) # However, the switch does not locate any RIP peers. How can you explain this result? A. B. C. D.
You have not set the switch's RIP priority peering in the RIP context j Your nearest RIP peer is more than 15 hops away. You have not enabled RIP for every VLAN where the switch is expected to locate RIP peers. You have not configured a static route to the nearest RIP peer.
Answer: C Section: (none) Explanation/Reference:
QUESTION 26 You have enabled IP routing on an-HP E8212 zI switch. You must configure the switch so that all packets with destination addresses not in its routing table are forwarded to 192.111.254.1 Which command accomplishes this task? A. E8212 (config)# ip route 255.255.255.255 192.111.254.1 B. E8212 (config)# ip default-route 192.111.254.1
C. E8212 (config) # ip route 0.0.0.0/0 192.111.254.1 D. E8212 (config) # ip helper 192.111.254.1/24 Answer: C Section: (none) Explanation/Reference:
QUESTION 27 What are the advantages of deploying 802.11n wireless technology instead of 802.11a technology? (Select two.) A. B. C. D. E.
5Ghz operating frequency support for centralized WLAN architecture backward compatibility with 802.11b higher transmission rates more powerful encryption options
Answer: CD Section: (none) Explanation/Reference:
QUESTION 28 What is the default operating mode of an HP E-MSM335 AP with factory default settings? A. B. C. D.
Sensor Mode VSC Mode Autonomous Mode Controlled Mode
Answer: C Section: (none) Explanation/Reference:
QUESTION 29 You must configure an HP E-MSM AP to support multiple VLANs for wireless traffic. Which configuration is required on the HP E3500yl switch connected to the AP? A. The switch port connected to the AP must be defined as an untagged member of each VLAN defined on the AP B. The switch port connected to the AP must be associated with the AP's Multi Service Controller. C. The switch port connected to the AP must be defined as a member of each VLAN defined on the AP. D. The AP port must be configured to acquire VLAN membership from a RADIUS server. Answer: B Section: (none) Explanation/Reference:
QUESTION 30 CORRECT TEXT How can you access the management interface of an HP E-MSM422 AP at factory default settings? Use your web browser to connect to https7/192.168.1 1 Configure a workstation to reside in the 192.168.1.0/24 network and accept a DHCP address from the AP. Connect the MSM AP to a PoE port that is a tagged member of a VLAN properly configured for DHCP relay, and use your web browser to connect to http://192168.1.1. Connect a workstation to the AP's bridge port using a DB9-to-RJ45 console cable. A. B. C. D. Answer: C Section: (none) Explanation/Reference:
QUESTION 31 You are designing a wireless network. Why should you choose an Autonomous architecture over Controlled architecture? (Select three.) A. to provide self-sufficient WLAN services, as well as local authentication and the ability to survive a WAN failure B. to provide wireless bridging from one building to another C. to provide coverage for a smaller, isolated area with only one or a few APs D. to provide effective coverage of large areas E. to provide fast Layer 2 roaming (< 50 ps) between RPs that are connected to the same Wireless Module F. to provide centralized management of RPs Answer: ABC Section: (none) Explanation/Reference:
QUESTION 32 A network administrator has successfully installed the HP ProCurve Manager remote client on his workstation. He can ping the PCM+ server, but he is denied access when trying to connect to the PCM+ server. The IP address of his workstation is 172.16.17.100/16. The IP address of the PCM+ server is 172.15.15.100/16. How can you resolve this problem? A. Add the IP address of the administrator's workstation to the access.txt file on the PCM+ server. B. Add 172.16.0.0/16 to the Managed Subnets list in the PCM+ discovery setup window C. Add a route to the 17.15.0.0/16 network on the switch connected to the client workstation.
D. Add the IP address of the administrator's workstation to the Authorized Managers list on the switch that the PCM+ server uses as a seed device. E. Add the administrator's user ID to the User Profiles in PCM+. Answer: A Section: (none) Explanation/Reference:
QUESTION 33 Which features are available in HP ProCurve Manager Plus (PCM+) but not in HP ProCurve Manager? (Select two.) A. B. C. D. E.
device mentioning automated software updates automatic discovery traffic monitoring network topology mapping
Answer: BD Section: (none) Explanation/Reference:
QUESTION 34 After using the Manual Discovery Wizard to add a switch to the HP ProCurve Manager Plus (PCM+) database, PCM+ still does not display a configuration for the switch. What can you do to obtain configuration information in PCM+? A. B. C. D.
Upgrade the switch's software to enable full PCM+ support. Use the Scan tool to update the configuration database for the switch. Move the switch's subnet to the Managed Subnets list. Move the switch's VLANs to the Managed VLANs list.
Answer: C Section: (none) Explanation/Reference:
QUESTION 35 How should you install an HP ProCurve manage Plus Remote Client? A. Configure a PCM+ Remote Agent to update all identical network workstations on managed subnets. B. Download a client installer from the My ProCurve website C. Direct a web browser on the client computer to http://:8040. D. Run the PCM+ installer and select "Client" instead of "Server" in the installation interface. Answer: C Section: (none) Explanation/Reference:
QUESTION 36 What is a benefit of the customizable airflow feature on the HP E6600 switch series? A. B. C. D.
relocates the power cord to the other side of the switch for ease of rack mounting controls the volume of airflow ensures the switch's exhaust is directed away from other equipment in data center racks regulates airflow, based upon the number of active ports
Answer: C Section: (none) Explanation/Reference:
QUESTION 37 Which view is indicated by the following prompt on an HP A7500 switch? [A7500] A. B. C. D.
operator Console System User
Answer: C Section: (none) Explanation/Reference:
QUESTION 38 Which A-Series switch is designed for the aggregation layer of data centers? A. B. C. D.
A5800 A9500 A12518 A12508
Answer: B Section: (none) Explanation/Reference:
QUESTION 39 Refer to the exhibit below. Given this configuration on an HP A-Series switch, which command is required to enable administrator level privileges? A. super password level 3 [simple|cipher] password B. privilege 3 password [simple|cipher] password
C. set administrator level password [simple|cipher] password D. local-user admin 1 level 3 Answer: B Section: (none) Explanation/Reference:
QUESTION 40 Which configuration options are available in User view at the CLI of an HP A-Series switch? (Select two.) A. B. C. D. E.
enable SSH save configuration changes configure management users restart the switch define a VLAN
Answer: BD Section: (none) Explanation/Reference:
QUESTION 41 What is the effect of the following command entered at the CLI of an HP A7500 switch? [A7500] quit A. B. C. D.
The switch restarts. The CLI prompts-you to enter a password, You are logged out of the system. The CLI displays the User view prompt.
Answer: D Section: (none) Explanation/Reference:
QUESTION 42 What is the effect of the following command entered at the CLI of an HP A12500 switch? [A12500] rip A. B. C. D.
RIP is enabled The administrator is prompted to enter "enable" or "disable." The CLI moves to the RIP view. The CLI displays the RIP configuration.
Answer: C Section: (none) Explanation/Reference:
QUESTION 43 What is the effect of the following command, entered at the CLI of an HP A7500 switch? boot-loader file cf:/A7500.bin main A. B. C. D.
The switch will upgrade the boot loader during the next boot cycle. The switch will immediately copy the application file A7500.bin from Compact Flash to the boot loader The switch will immediately copy the application file A7500.bin from the boot loader to Compact Flash, The switch will use the application file A7500 bin: during the next boot cycle.
Answer: D Section: (none) Explanation/Reference:
QUESTION 44 You must configure an IPv4 address on an HP A5820 switch. Which view enables you to accomplish this task? A. B. C. D.
System VLAN Interface Ethernet interface IP Interface
Answer: A Section: (none) Explanation/Reference:
QUESTION 45 You have defined port 1/0/2 on an HP A7500 switch as a trunk port with VLANS 1, 10, 20, 30 permitted. What is the effect of the following command? [A7500-GigabitEthernetl/0/2] port trunk pvid vlan 30 A. B. C. D.
The port will be added to VLAN 30 as a tagged member. The port will carry VLAN 30 as an untagged VLAN; all others will be tagged. The port will preconfigure as a hybrid port carrying VLAN 1 and VLAN 30 as untagged VLANs. The port will use VLAN 30 as its default VLAN and wi II no longer forward VLAN 1 packets
Answer: D Section: (none) Explanation/Reference:
QUESTION 46 What is the VLAN status of the ports on an HP A-Series switch at factory default settings? A. All ports are in a learning state waiting for VLAN assignment through GVRP. B. All ports are access ports using VLAN 1 as their default VLAN.
C. VLANs are unassigned until a port mode is defined. D. All ports are trunk ports using VLAN 1 as their default VLAN Answer: B Section: (none) Explanation/Reference:
QUESTION 47 Place each A-Series port type next to its description
Answer:
Section: (none) Explanation/Reference:
QUESTION 48 Which potential problem is addressed by BPDU Protection on HP A-Series switches? A. B. C. D.
a technician accidentally inserting a switch running STP into an MSTP region a technician accidentally configuring two switches to be Root Bridge in an MSTP instance a technician accidentally disrupting a Spanning Tree by connecting a switch to an edge port a technician accidentally configuring a switch to run PVST+ instead of MSTP
Answer: C Section: (none) Explanation/Reference:
QUESTION 49 Which command will configure an HP A-Series switch to be the Root Bridge in MST instance 1? A. B. C. D.
[Switch] mstp root instance 1 [Switch] spanning-tree instance 1 priority 0 [switch] stp instance 1 root primary [Switch] stp instance 1 priority root
Answer: C Section: (none) Explanation/Reference:
QUESTION 50 What is the default load-balancing behavior for Layer 2 traffic forwarded over aggregated links on an HP ASeries switch? A. B. C. D.
Load balancing is based on the source MAC address only. Load-balancing is based on the destination MAC address only. Load-balancing is based on the source MAC address and the destination MAC address. Load-balancing is based on the source MAC address and egress port
Answer: C Section: (none) Explanation/Reference:
QUESTION 51 Which link aggregation protocol is supported by HP A-Series switches? A. B. C. D.
HP Port Trunking Port Aggregation Protocol (PAgP) Link Aggregation Control Protocol (LACP) Multi-Link Trunking (MLT)
Answer: C Section: (none) Explanation/Reference:
QUESTION 52 What is indicated by the-1 in the following prompt from an HP A-Series switch? [Switch-Gigabit Ethernet 1/0/23]
A. B. C. D.
IRF stack ID IRF member ID IRF master priority IRF port number
Answer: B Section: (none) Explanation/Reference:
QUESTION 53 Which topologies are supported by an IRF stack? (Select two.) A. B. C. D. E.
tree mesh ring star daisy chain
Answer: BE Section: (none) Explanation/Reference:
QUESTION 54 What is the default IRF priority setting on an HP A-Series switch? A. B. C. D.
0 1 32 auto-assigned
Answer: B Section: (none) Explanation/Reference:
QUESTION 55 What is the maximum number of APs that can be managed by an HP A-WX5004 Wireless LAN Controller? A. B. C. D.
32 128 256 512
Answer: C Section: (none) Explanation/Reference:
QUESTION 56 Which command entered at the CLI of an HP E3500 yl switch displays dynamic information about traffic transmitted and received on each port? A. B. C. D.
E3500 yl# show interface traffic E3500 yl# show interface all E3500 yl# show interface display E3500 yl# show interface dynamic
Answer: C Section: (none) Explanation/Reference:
QUESTION 57 You have configured IP helper addresses for VLAN 5 and VLAN 6 on this HP E5406 zl switch. However, users in these VLANs report that their computers are not receiving DHCP addresses Which feature must be enabled to address this problem? A. B. C. D.
DNS DHCP relay IP routing DHCP snooping
Answer: B Section: (none) Explanation/Reference:
QUESTION 58 Port B1 on an HP ProCurve 5406zl switch is an untagged member of VLAN 155 and not a tagged member of any VLAN. Port C1 is a tagged member of VLAN 155 and an untagged member of VLAN 100. You issue the following command: 5406zl(config)# no vlan 155 Why do you receive the following prompt? The following ports will be moved to the default VLAN: B1 Do you want to continue? [y/n] : A. B. C. D.
The CLI always issues this prompt when deleting a VLAN. The CLIwill not allow you to orphan a port. The CLI will not delete a VLAN with any port membership. All ports must be moved to the default VLAN before you can delete the VLAN.
Answer: D Section: (none) Explanation/Reference:
QUESTION 59
After issuing the following two CLI commands, how can you gain access to the CLI of the switch if the manager and operator passwords have been lost? E5406 (config)# no front-panel-security password-clear E5406(config)# no front-panel-security factory-reset
A. Power cycle the switch and access the ROM console to clear passwords at the manager prompt. B. Press the Reset and Clear buttons on the switch's front panel, release the Reset button and hold the Clear button until the all switch LEDs blink rapidly. C. Contact support and obtain a one-time password to gain access to the switch. D. Reset the passwords using the Secure Access Wizard i n ProCurve Manager Plus. Answer: A Section: (none) Explanation/Reference:
QUESTION 60 You have configured a dynamic LACP four-port trunk connecting two HP E-Series switches How will the switches share the load over the trunk? A. The switch that receives the first packet in each conversation will balance the load by ensuring reply packets use a different link. B. Each switch will assign conversations to links independent of the other switch's selection. C. The switches will exchange LACP BPDUs to negotiate a load-sharing algorithm. D. The switches wi II dynamically calculate the path of least congesti on for each conversation Answer: B Section: (none) Explanation/Reference:
QUESTION 61 What is indicated by this entry in the IP route table of an HP E8212 zl switch? A. The switch has been configured with an ACL that blocks communications with the loopback interfaces. B. The switch does not permit communications with any loopback interface. C. Traffic to this interface is rejected with the single exception of traffic to the host address of the switch's loopback interface (127.0.0.1/ 32). D. A loopback interface is configured with 127.0.0.0. Answer: C Section: (none) Explanation/Reference:
QUESTION 62 You have enabled RtPv2 with the following command at the CLI of an HP E3500 yI switch: E3500(config)# router rip E3500(rip)#
However, the switch does not locate any RIP peers. How can you explain this result? A. B. C. D.
You have not set the switch's RIP pri onty peeri ng i n the RIP context Your nearest RIP peer is more than 15 hops away. You have not enabled RIP for every VLAN where the switch is expected to locate RIP peers. You have not configured a static route to the nearest RIP peer.
Answer: C Section: (none) Explanation/Reference:
QUESTION 63 You have enabled IP routing on an HP E8212 zl switch. You must configure the switch so that all packets with destination addresses not in its routing table are forwarded to 192.111.254.1. Which command accomplishes this task? A. B. C. D.
E8212(config)# ip route 255.255.255.255 192.111.254.1 E8212(config)# ip default-route 192.111.254.1 E8212(config)# ip route 0.0.0.0/0 192.111.254.1 E8212 (config)# ip helper 192.111.254.1/24
Answer: C Section: (none) Explanation/Reference:
QUESTION 64 What is the VLAN membership of wireless traffic entering a switch from an HP E-MSM AP with default VLAN settings? A. B. C. D.
tagged VLAN 192 untagged VLAN on a connected switch port tagged VLAN 2100 untagged VLAN assigned by RADIUS profile
Answer: B Section: (none) Explanation/Reference:
QUESTION 65 What are the advantages of deploying 80211 n wireless technology instead of 802.11a technology? (Select two) A. B. C. D. E.
5Ghz operating frequency support for centralized WL AN architecture backward compatibiiity with 802 11b highertransmission rates more powerful encryption options
Answer: CD Section: (none) Explanation/Reference:
QUESTION 66 You are the network administrator at a company with multiple remote sites. You are using HP ProCurve Manager Plus (PCM+) to manage network devices in all of the company's offices. How can PCM+ remote agents help manage your network? A. B. C. D.
They enforce policies defined on the PCM+ server and discover manageable devices. They detect unauthorized PCM+ servers and quarantine unauthorized switches and hubs. They detect unauthorized PCM+ servers and clients. They manage access by remote clients and coordinate communications across subnets.
Answer: A Section: (none) Explanation/Reference:
QUESTION 67 Alter using. the Manual Discovery Wizard to add a switch to the HP ProCurve Manager Plus (PCM-) database.PCM+ still not display a configutaiion or the switch. What can you do to obtain configuration information in PCM+? A. B. C. D.
Upgrade the switch's softwaie to enable full PCM+ support Use the scan tool to update the configuration database for the switch Move tne switch's subnet io the Managed Subnets list Move the switch's VLANs to the Managed VLANs list
Answer: C Section: (none) Explanation/Reference:
QUESTION 68 At a customer site, network administrators report that an HP ProCurve Manager Plus (PCM+) server does not discover any manageable devices except those on the subnet where the server resides. What is a possible solution to this problem? A. issuing an SNMP GET for a device on the desired subnets from the PCM+ server B. pinging a device in the desired subnets from the PCM+ seiver C. using the Subnet Discovery Wizard on the PCM+ server to add manageable devices in the desired subnets D. adding the desired subnets with the Manual Discovery Wizard on the PCM+ server Answer: C Section: (none) Explanation/Reference:
QUESTION 69 Which features of the HP E8200 zI switch series are not available on E-Series switches? (Select Two) A. B. C. D. E.
support for 10Gig modules multiple firmware versions redundant management modules multiple configuration files redundant switch fabric
Answer: CE Section: (none) Explanation/Reference:
QUESTION 70 How is the first Telnet interface for A-Series switches identified in the CLI? A. B. C. D.
interface com 0 interface remote interface vty 0 interface aux 0
Answer: C Section: (none) Explanation/Reference:
QUESTION 71 Which A-Series switch is designed for the aggregation layer of data centers? A. B. C. D.
A5800 A9500 A1251J A1250J
Answer: B Section: (none) Explanation/Reference:
QUESTION 72 Which upgrade method enables an administrator to upload a new application file to an MSR Series router located in a remote site? A. B. C. D.
TFTP/FTP USB flash drive Boot Menu XModem
Answer: A Section: (none) Explanation/Reference:
QUESTION 73 What is the effect of the following command entered at the CLI of an HP A12500 switch? [A12500] rip A. B. C. D.
rip is enabled. The administrator is prompted to enter "enable" or "disable." The CLI moves to the RIP view. The CLI displays the RIP configuration
Answer: C Section: (none) Explanation/Reference:
QUESTION 74 Which interface is available for managing an HP A-Series router at factory default settings? A. B. C. D.
Telnet web console menu
Answer: C Section: (none) Explanation/Reference:
QUESTION 75 You must configure port GigabitEthernet 1/0/1 on an HP A-Senes switch so that it can support policy-based VLANs and port-based VLANs Which type of port is required to support this configuration? A. B. C. D.
trunk tagged hybrid access
Answer: B Section: (none) Explanation/Reference:
QUESTION 76 You must configure an IPv4 address on an HP A5820 switch Which view enables you to accomplish this task?
A. B. C. D.
System VLAN Interface Ethernet Interface IP interface
Answer: B Section: (none) Explanation/Reference:
QUESTION 77 You have defi ned port 1 /0/2 on an HP A7500 switch as a trunk port with VL ANS 1,10,20.30 permitted What i s the effect of the followi ng command? [A7500-GigabitEthernetl/0/2] port trunk pvid vlan 30 A. B. C. D.
The port will be added to VLAN 30 as a tagged member The port will carry VLAN 30 as an untagged VLAN; all others will be tagged. The port will be reconfigured as a hybrid port carrying VLAN 1 and VLAN 30 as untagged VLANs. The port will use VLAN 30 as its default VLAN and will no longer forward VLAN 1 packets.
Answer: D Section: (none) Explanation/Reference:
QUESTION 78 You have entered the following command at the CLI of an HP A5800 switch: [A5800] interface bridge-aggregation 14 Which step is necessary to complete configuration of a link-aggregation group? A. B. C. D.
Enter aggregate group 14 in the Lag-14 view. Enter port-trunk in the Bridge-aggregation view. Enter port-link aggregation group 14 inthe Interface viewfoj each porttnthe group. Enter bind-agg-group 14 in the Global Configuration view
Answer: C Section: (none) Explanation/Reference:
QUESTION 79 Which command wilt configure an HP A-Series switch lo be the Root Bridge in MST instance 1? A. B. C. D.
[Switch] mstp root instance 1 [Switch] spanning-tree instance 1 priority 0 [Switch] stp instance 1 root primary [Switch] stp instance 1 priority root
Answer: C
Section: (none) Explanation/Reference:
QUESTION 80 What is the default IRF priority setting on an HP A-Series switch? A. B. C. D.
0 1 32 auto-assigned
Answer: B Section: (none) Explanation/Reference:
QUESTION 81 Which topologies are supported by an IRF stack? (Select two.) A. B. C. D. E.
tree mesh ring star daisy chain
Answer: CE Section: (none) Explanation/Reference:
QUESTION 82 Place each type of AP next to its description.
Answer:
Section: (none) Explanation/Reference:
QUESTION 83 You must update the software on an HP E3500 yl switch. Which devices can be sources for the copy command? (Select two.) A. B. C. D. E.
USB flash drive management workstation hard drive TFTP server FTP server Compact Flash card
Answer: AC Section: (none) Explanation/Reference:
QUESTION 84 You must determine whether routing has been enabled on an HP E 5406 zl switch. Which commands provide this information? (Select two.) A. B. C. D. E.
show interfaces show running-config show vlans show ip route show ip
Answer: BE Section: (none) Explanation/Reference:
QUESTION 85 Which E-Series CLI commands enable you to view all show commands available in the current context? (Select two.)
A. B. C. D. E. F.
Switch# show /? Switch# show all Switch# show help Switch# show ? Switch# show Switch# help show
Answer: DE Section: (none) Explanation/Reference:
QUESTION 86
Which HP A-Series switch in an IRF stack will become Master if an election is required? A.
the switch with the lowest bridge MAC address B. the switch that is the current Master C. the switch with the longest uptime D. the switch with the highest IRF Master priority Answer: B Section: (none) Explanation/Reference:
QUESTION 87
Which VLAN will be carried untagged on GigabitEthernet 2/0/2?
A.
VLAN 1 B. VLAN 100 C. VLAN 101
D.
VLAN 102
Answer: A Section: (none) Explanation/Reference:
QUESTION 88
How does this HP E5406 zl route packets destined for the 192.168.0.0 network?
A.
The switch load balances conversations to the 192.168.0.0 network between 172.16.16.1 and 172.17.17.1.
B.
The switch forwards packets with destinations in the 192.168.254.0/24 address range to 172.17.17.1. All other packets addressed to hosts in the 192.168.0.0/16 address range are forwarded to 172.16.16.1. C. The switch forwards packets addressed to hosts in the 192.168.0.0/16 address range to 172.16.16.1. The route statement for the 192.168.254.0/24 address range is ignored. D. The switch uses the route to 172.17.17.1 as a backup route in the event that its link with 172.16.16.1 goes down. Answer: B Section: (none) Explanation/Reference:
QUESTION 89
You must configure an HP E3500 yl switch for installation in a network that uses a mix of STP and RSTP. What must you do to ensure that the E3500 will interoperate with other switches in this Spanning Tree? A.
Enterspanning-tree config-revision stpin the configuration context for every VLAN the switch shares with another switch. B. Enterspanning-tree force-version all-stp-operationin the global configuration context.
C.
Enterspanning-tree mode stp rstpin the configuration context of every port where the switch will hear Spanning Tree BPDUs. D. Enterspanning-treein the global configuration context. Answer: D Section: (none) Explanation/Reference:
QUESTION 90
What is the effect of the following command issued at the CLI of an HP E3500-24G yl switch? E3500-24G#show logging 24 A.
The CLI displays all events logged in the previous 24 hours. B. The CLI displays all events in the system log that include the string "24". C. The CLI displays all events associated with port 24. D. The CLI displays all events associated with all ports. Answer: B Section: (none) Explanation/Reference:
QUESTION 91
Which type of link aggregation is enabled by the following command, entered at the CLI of an HP E5406 zl switch? E5406(config)# trunk b1-b4 trk3 A.
static LACP B. dynamic LACP C. HP port trunk D. passive LACP Answer: C Section: (none) Explanation/Reference:
QUESTION 92
You have configured Multiple Spanning Tree Protocol (MSTP) on two HP E8212 zl switches and four E5406 zl switches, but they have not joined the same MST region. Which configuration parameters should you verify to ensure all switches join the same region? (Select three.) A.
VLAN-to-instance mappings
B.
bridge priorities port priorities D. configuration name E. BPDU Protection settings F. configuration revision C.
Answer: ADE Section: (none) Explanation/Reference:
QUESTION 93 Which HP E-Series switch models display the following prompt in the interface configuration context? (Select two) HP Switch (eth-A24)# A. B. C. D. E.
E8212zl E6600-24G E5412-96GZI E2910-24Gal E350CM8G-POEyI
Answer: AC Section: (none) Explanation/Reference:
QUESTION 94 Which statements are true about the primary and secondary flash areas of an HP E-Series switch? (Select two) A. The primary area contains the switch's operating system, which is automatically copied to the secondary area whenever the switch is restarted. B. The switch can be started using the software stored in either area. C. The software stored in the primary area is always used to start the switch. D. The primary area always contains the most recent software version; the secondary area contains an earlier version to be used if the primary version. E. The software in each area is stored and managed independently Answer: BE Section: (none) Explanation/Reference:
QUESTION 95 Which security technology requires that you set read/write community names? A. SFTP B. SSH
C. SNMP D. HTTPS E. SMTP Answer: C Section: (none) Explanation/Reference:
