AUTINOR Vocal Synthesiser Installation manual

Programme: SYNI 1-V00 181001

Edition No4 - 27 March 2003

&

Documentation Dpt.

Installation Manual

Page 3

This manual is deemed correct on going to press.

The information contained has been scrupulously checked. However AUTINOR declines al1 responsibility for error or omission. Should you notice any discrepancy or unclear description, or if you have any suggestions, we would appreciate your written comments (by mail fax or Email) to: AUTINOR SA Company - Documentation Department Z.A. Les Marlières 59710 AVELIN ? [33] 03-20-62-56-00 [33] 03-20-62-56-41 [XI [email protected]

This manual is the property of AUTINOR, from whom it may be bought (at the above address). It may however by freely copied in order to communicate information to those who might need it. We can only authorise a complete copy, without neither addition nor removal of information

Where quotations are taken, the following at least must be noted: The Company name of AUTINOR, - The version of the software to which it corresponds, - The date of the original edition. -

O Copyright 200 1 AUTINOR All rights reserved.

@ Documentation Dpt.

Installation Manual

CONTENTS

Preamble ...................................................................................................... 6 Generalities .....................................................................................6 Characteristics ................................................................................. 6 Connecting ................................................................................................... 7 In Decimal mode (1 wire per level) .................................................. 7

In "CREP" mode ..............................................................................7 Parameters................................................................................................... 8 The messages.............................................................................................. 13 Recording the messages by phone .................................................13 Recording the messages by P.C. ....................................................14 Recording of the synthesis memory by programmer ....................... 14 Automatic doubling of a programmed board ....................................14 Example of vocal messages .......................................................... 1 4

Page 5

I

&

Documentation Dpt.

Installation Manual

Page 6

PREAMBLE You have just acquired Our new voice synthesis card and let us congratulate you. You will find in this manual, al1 information allowing you to bring it into service.

Generalities Card SYNI 1 replaces card SYN08 (preceding generation) with certain additive functions: Possibility of use the diagnostic tool (VEC03) to parameter the card, Function with the 2 types of Autinor CREP (ID & AF), Possibility of re-recording the messages with "analogie" headset telephone connected directly on the card. The functions first of the SYN08 are maintained: Function in decimal mode or CREP (AUTINOR), Start of ,the messages by validation input or not, Possibility to repeat the messages or not, Selection of common 24V or OV, Put in possible "cascade" (loss of volume which can be compensated by adjustment of the volume potentiometer).

Characteristics The SYNI 1 Card has a capacity of 90

seconds recording broken up as follows:

24 messages of 3 seconds (1 to 24) 4 messages of 4.35 seconds. (25 to 28) If higher messages are necessaries, it can be associate themselves. It has 16 distinct inputs from selection of the messases and 1 input of validation. The affected message at each entry can be programmed. According to the parameter setting of the input, the message can be started after validation or not like repeated or not. The higher the number of the input is, the more the input has priority. Example: If the contact of overload is connected to the input E12, that it is active, and that the input E3 is also active, the message of the input E l 2 will be pronounced before ,the message of the input E3.

In the case of operation by CREP, the assignment of the message according to code CREP is parameterised. ~ u p p Voltage: ~y 12V to 28V continuous Power sound: 5 W (12V14 Ohms or 2 4 V l 16 Ohms) Loud speaker: 4 / 8 1 16 Ohms

@--Documentation Dpt.

Installation Manual

Page 7

CONNECTING Connecting in Decimal mode

Connecting in "AUTINOR" CREP mode

U

E4

E6

E8

lnput of VAlidation VA Additionna1 2 t o 16

Loudapeaker lnput for "CAscade" functionCA