D Gate - FCC ID

13 juin 2013 - Reinforced Concrete. Iron. Reinforced Concrete. Nylon Insulation ring. (included in installation set). Retainer ring (not included in installationset).
3MB taille 9 téléchargements 370 vues
!D Gate

1x !D Gate

dimensions

300 150(2x)

1x Coax cable 3m/10ft

distance between antennas

13(6x)

70mm / 2.8” 70

57mm / 2.2” 57

10 (floorpart)

828.75mm 828,75/ 2.7ft 1024.25mm 1024,25/ 3.4ft

1668mm 1668/ 5.7ft

195,5

195.5mm / 7.7”

60(2x)

462mm 462/ 18.2”

recommended - 2.0m / 6.5ft absolute max. - 2.2m / 7ft

100mm / 3.9” 100

orientation in the shop Power inserter B

A B

all antennas in the same direction.

B

A

B

A

B

A

stock room

sales floor B

B

A

A

A

drw: CB 2013/06/13

GROENLO - HOLLAND

chk:

description:

doc. article no: 5278988

quick reference !D Gate

rev. : C.01

Copyright © by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be reproduced or distributed in any form or by any means, or stored in a data base or retrieval system without the prior written permission of NEDAP.

sheet: 45.01 of 1 drawing: T5278-988

01

02

remove covers

drilling holes

150

150mm / 5.9”

300

300mm / 11.8”

13mm / 0.5” 13 (6x)

60

60mm / 2.4”

90mm / 3.5”

ø 13mm / ø 0.5”

03

04

4x 4

M10 3

Metal M10 2

Nylon M10 (included in installation set)

Cleaning

Hilti-hit

1

Place nut

Hilti-hit not included

05

Nut (not included in installationset) Retainer ring (not included in installationset) Nylon Insulation ring (included in installationset)

Nut (not included in installationset)

Retainer ring (not included in installationset) Nylon Insulation ring (included in installation set)

Iron

Iron Reinforced Concrete

Reinforced Concrete

Always mount an antenna insulated to the floor or wall

Always mount an antenna insulated to the floor or wall

power supply

processing unit

Out

In Power for Reader network IN USB host network OUT USB service port

Power supply 9561811. One needed for every installed system. (not included) Not compatible with IEEE 802.3a* standard Recommended to place in switch-room

1 Yellow Heartbeat 2

1

3

4

5

7

6

1 2 3

8

9

2 Green 10

11

3 Green

Disk access 12

Firmware running H

H

+ -

buzzer

G

G

1 Green 2 Blue F

Blue

Processing unit at output Blink

No device at output or Lan- modem (in case of OST integration)

Continuous Power inserter at output

3 Red

F

Power error

E

E

D

!D Reader

previous C

next

Led Blue -

Orange

Red

Firmware running Error

Green

Green

RFID active

Power

no coax cable needed coax cable 3m / 10ft

1m / 3ft 0.5m / 1.5ft

2x coax cable 3m / 10ft

1m / 3ft

2m / 6ft

1m / 3ft

required label free zone recommended label free zone

2m / 6ft

1m / 3ft 0.5m / 1.5ft

01 2



1

coax cable

previous



next

coax cable Minimum bending radius = >60mm/2.4”

coax-cable 3m/10ft

02

2

1

note: use only cat5e ethernet cable or better, with all 8 wires connected.(straight cable)

processing unit network IN OUT IN

RJ45 connector to ethernet outlet - customer network.

03

2

processing unit network IN

place covers

1

note: use only cat5e ethernet cable or better, with all 8 wires connected.(straight cable)

processing unit network OUT

RJ45 connector to ethernet outlet - customer network.

connect voltage supply

230V 110V

Note : The start up of all the processes takes approximately 3 minutes.

use firmware configuration quick reference.

Model: !D Gate Region 2 FCC ID: CGDSTOREIDG

IC: 1444A-STOREIDG

This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Cet appareil se conforme aux normes RSS 210 exemptés de license du Industry Canada. L’opération est soumis aux deux conditions suivantes: (1) cet appareil ne doit causer aucune interférence, et (2) cet appareil doit accepter n’importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu de cet appareil. Les changements ou modifications n’ayant pas été expressément approuvés par la partie responsable de la conformité peuvent faire perdre à l’utilisateur l’autorisation de faire fonctionner le matériel. FCC and IC Radiation Exposure Statement: This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 3.65 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement  est  conforme  a  RSS-102  limites  énoncées  pour  un  environnement  non  contrôlé.  Cet  équipement  doit  être  installé  et utilisé avec une distance minimale de 3.65 cm entre le radiateur et votre corps. This Class B digital apparatus complies with Canadian ICES-003 Cet  appareil  numérique  de  Classe  B  est  conforme  à  la  norme  Canadienne  ICES-003