05/13/02 – 13 mai 2002 BODY - CONVERTIBLE TOP BOOT FIT FORD: 2001-2002 MUSTANG ISSUE Some Mustang convertible vehicles may exhibit difficulty in securing the convertible top boot (cover), which may result in a poor fit. This may be caused by the snaps not holding the boot securely in place. ACTION Alternative fasteners will need to be installed on the boot and interior quarter trim panel. Refer to the following Service Procedure for details. SERVICE PROCEDURE To Service The Boot: Order 2R3Z-76546A34-AA Convertible Top Boot Fastener Kit to repair.
1. Using a pair of pliers, remove the socket of the snap, located on the convertible boot (Figure 1). 2. Remove the remaining portion of the snap, by grabbing the stud with the pliers and pulling it out of the substrate in a twisting motion.
3. Locate the punch into the remaining slot (Figure 2) in the boot. Center the oval inside of the punch with the center of the slot. Lay the slot of the boot over a softer surface (ie. wood) and strike the punch with a hammer. 4. Verify that the punch has gone completely through the boot material.
5. Line up the prongs on the grommet with the marks left by the punch teeth (Figure 3). Insert the grommet into the hole from the top side of the boot. 6. Verify that all four (4) prongs are protruding through the backside of the boot. Place the oval washer inside the prongs of the grommet.
7. Using your fingers or pliers, push the prongs of the grommet over the washer. Tap the washer with a hammer to fully seat the prongs. NOTE HITTING THE WASHER TOO HARD MAY DISTORT THE EYELET. 8. Repeat these steps for the other end of the boot. To Service The 1/4 Trim: 1. Raise the convertible top to half mast. CAUTION THE CONVERTIBLE TOP LIFT CYLINDERS MAY LOWER DURING THE REPAIR. 2. On the interior trim, remove the snap's center screw and nut. Remove the snap from the trim panel. 3. Enlarge the hole in the trim panel using an 11/64" drill bit. 4. Insert the new 1/4 turn fastener into the panel (it may be necessary to screw it in). 5. Install the new washer and nut onto the stud from the underside of the panel. Tighten this nut to 4.1 +/- 0.7 N.m (36 +/- 6 Lb-in). While tightening, make sure that the fastener will line up with the boot grommet. 6. Repeat these steps for the other side of the vehicle. 7. Completely lower convertible top. 8. Install convertible boot per Owners Manual with the exception of the snap. 9. Place the grommet part of the boot over the New 1/4 trim fastener. 10. Turn the fastener to keep the boot in place. 11. Repeat these steps for the other side of the vehicle. 12. Verify that the new fasteners are holding the boot securely in place. 13. Remove the convertible top boot. 14. Close the convertible top.
Parts Block OTHER APPLICABLE ARTICLES: NONE WARRANTY STATUS: Eligible Under The Provisions Of Bumper To Bumper Warranty Coverage OPERATION
DESCRIPTION
TIME
020908A
Install Alternate Fasteners On The Boot And interior Quarter Trim Panels
pare-chocs, les grands jouets et d'autres objets que l'enfant pourrait empiler pour sortir. ⢠Lorsque votre enfant est capable de sortir du berceau ou lorsque sa ...
26 sept. 2014 - pare-chocs, les grands jouets et d'autres objets que l'enfant pourrait empiler pour sortir. ⢠Lorsque votre enfant est capable de sortir du berceau ...
26 sept. 2014 - Do not use this crib if the enclosed or attached instructions cannot be strictly adhered to. ⢠Always .... LISTE DES PIÃCES / PARTS LISTING. « ».
26 sept. 2014 - ... inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT ... 4 pieds de bois « C » aux 2 pièces têtes de lit « A ».
A child can trap parts of the body or clothing on loose fasteners. Check this crib regularly before using it, and do not use it if any part is loose or missing or if there are any signs of damage. Do not substitute parts. Contact KIDIWAY Inc. If repl
26 sept. 2014 - pare-chocs, les grands jouets et d'autres objets que l'enfant pourrait empiler pour sortir. ⢠Lorsque votre enfant est capable de sortir du berceau ...
rangement shown in Fig. 2. This system was based on using a conversion of the existing pedals. By using a ... and the last one looked like the answer. In essence, ... in Figure 3. The ribbed rubber pads shown were part of a bicycle pedal.
As per above drawing, attach the left side panel âCâ to ... the side panels âCâ and âDâ by using 1 bolt âP on ... port is installed flat side up, with the sharp edges.
preparations get underway to open the country's first deradicalisation centre in ... centres will open over the coming months across France, as the government ...
Un avis que partage Hilla Levy Aslan, coach sportive à l'Orange Bleue Strasbourg parc des. Forges. En un an, elle a assisté au départ de 20% de la clientèle de ...
such requirements, with the current edition of the National Building Code, and / or ASHRAE's âGood Engineering Practicesâ. Fantech reserves the ..... living areas. Fantech heat recovery ventilators (HRV) that use a supply fan shutdown for frost p
Information in this document, including URL and other Internet Web site references, is subject ...... CD-ROM, or downloading and executing the image from RAM.
network bootstrap program (NBP) file â the boot image file that contains the executable ... Page 4 .... To learn more about 3Com solutions, visit www.3com.com.
dans la page de réponse (voir par exemple le site des éditions Eyrolles) ..... entrants et sortants de cette page, soit sous forme linéaire, soit sous forme ...
Une main-d'oeuvre spécialisée et scolarisée. Une fiscalité et des coûts avantageux. Des infrastructures de classe mondiale. Une qualité de vie incomparable.
