and CE Code requirements. Use with ... conduit. NOTICE: Multi-service applications must connect power through hubs labeled "POWER". Single service ... Position the floor box with the top of riser, even with, or above slab level. Use screws ...
CFBS1R4PFB MULTI-SERVICE RECESSED NON-METALLIC FLOOR BOX FOR 4" ROUND COVER Installation Instructions ENGLISH CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing or servicing. NOTICE: For installation by a qualified electrician in accordance with all national and local electrical codes, communications standards, the following instructions and any instructions included with individual devices. NOTICE: Insure data/communications circuits are separated from lighting/power circuits in accordance with the NEC and CE Code requirements. Use with CFBS1R4CVRxx series round covers. 1. Make conduit connections in accordance with application and applicable electric codes. Cement conduit closure plugs to unused ports or use conduit reducers provided with box. NOTICE: Knockouts must be removed from closure plug for use with conduit. NOTICE: Multi-service applications must connect power through hubs labeled "POWER". Single service
applications can use any hub connection. 2. Verify that concrete cover is secure. Cover visible openings and screws that penetrate the floor box with tape to prevent concrete from entering the box. 3. Position the floor box with the top of riser, even with, or above slab level. Use screws and wire to keep the floor box from moving during concrete pour. NOTICE: Recommended depth of pour for all applications is 5-1/2 inches [140 mm]. Minimum depth of pour is 5 inches [127 mm] with restricted wiring chamber depth of 1-3/4 inches [44 mm].
5.00 [127] MIN POUR DEPTH
5.50 [140] RECOMMENDED POUR DEPTH
FLOOR BOX VOLUMES AT 5 INCH [127 MM] MINIMUM HEIGHT VOLUME (IN ) VOLUME (CM ) CONFIGURATION SINGLE SERVICE 67.0 1098 MULTI-SERVICE (POWER) 557 34.0 MULTI-SERVICE (DATA) 31.0 508 ADDITION VOLUME FOR EACH 1/2 INCH [12.7 MM] HEIGHT VOLUME (IN ) VOLUME (CM ) CONFIGURATION SINGLE SERVICE 6.5 107 MULTI-SERVICE (POWER) 3.0 49 MULTI-SERVICE (DATA) 57 3.5 Wiring Device - Kellems Hubbell Incorporated (Delaware) Shelton, CT 06484 1-800-288-6000 www.hubbell-wiring.com
PD-2676
7/15
CFBS1R4PFB BO TE DE PLANCHER ENCASTR E NON M TALLIQUE MULTI-SERVICE ACCEPTANT LES COUVERCLES RONDS DE 10 cm Directives de montage
FRAN AIS
ATTENTION - RISQUE DE CHOC LECTRIQUE. D brancher le circuit avant de proc der au montage ou la maintenance. AVIS - Doit tre install par un lectricien qualifi conform ment aux codes de l' lectricit nationaux et locaux et selon les normes de communication, les directives suivantes et les directives accompagnant les dispositifs individuels. AVIS - S'assurer de s parer les circuits d' nergie des circuits de donn es/communications conform ment aux exigences du CCE. Utiliser avec les couvercles ronds de la s rie CFBS1R4CVRxx. 1. R aliser les connexions de conduit selon l'application et les codes de l' lectricit applicables. Cimenter les obturateurs des ports inutilis s ou se servir des r ducteurs de conduits fournis avec la bo te. AVIS - Retirer les d bouchures des obturateurs utilis s avec des conduits. AVIS - Pour les applications multi-service, la source d' nergie doit p n trer dans les raccords d'arriv e identifi s NERGIE . Dans le cas d'un service simple, utiliser n'importe quel raccord d'arriv e. 2. V rifier que le couvercle b ton est s curitaire. Recouvrir les ouvertures visibles et les vis entrant dans la bo te de plancher de ruban adh sif pour emp cher le b ton d'y p n trer. 3. Positionner la bo te de plancher de niveau avec le haut de la couronne de b tonnage, galit ou au-dessus de la dalle. Se servir de vis et de fils de fer pour emp cher la bo te de plancher de se d placer pendant la coul e. AVIS - La profondeur de coul e recommand e pour toutes les applications est de 140 mm. La profondeur de coul e minimale est de 127 mm lorsque la profondeur de la chambre de c blage se limite 44 mm.
CONFIGURATION SERVICE SIMPLE MULTI-SERVICE ( NERGIE) MULTI-SERVICE (DONN ES)
VOLUMES DES BO TES DE PLANCHER LA HAUTEUR MINIMALE DE 127 mm 1098 CM 557 CM 508 CM
VOLUME ADDITIONNEL POUR CHAQUE 12,7 mm DE HAUTEUR 107 CM 49 CM 57 CM
CFBS1R4PFB CAJA NO-MET LICA para PISO con cubierta de 10 cm instrucciones de instalaci n
ESPA OL
PRECAUCI N: RIESGO DE CHOQUE EL CTRICO. Desconecte la energ a antes de instalar o dar mantenimiento. AVISO: Para ser instalada por un electricista calificado de acuerdo con todos los c digos el ctricos nacionales y locales, los est ndares de comunicaciones, las instrucciones siguientes y cualquier instrucci n incluida con los dispositivos individuales. AVISO: Aseg rese que los circuitos de datos/comunicaciones queden separados de los circuitos de iluminaci n/energ a de acuerdo con los requisitos del c digo NEC y del CEC. Para utilizaci n con las cubiertas redondas de la serie CFBS1R4CVRxx. 1. Haga las conexiones del tubo conduit de acuerdo con la aplicaci n y los c digos el ctricos aplicables. Cemente los tapones de conduit no utilizado o utilice los reductores de conduit proporcionados en la caja. AVISO: Los tapones desprendibles se deben quitar de la tapa para uso con tubo conduit. AVISO: Para aplicaciones Multi-servicio, se deben conectar los cables de energ a a trav s de las entradas etiquetadas POWER (ENERG A) . Los servicios nicos, pueden utilizar cualquier conexi n. 2. Verifique que la cubierta para concreto est segura. Cubra las aberturas visibles y los tornillos que entran en la caja de piso con cinta para evitar que el concreto entre en la caja. 3. Coloque la caja de piso con la tapa alineada o sobre el nivel de la losa. Utilice lo tornillos y alambre para mantener fija la caja de piso durante el vaciado del concreto. AVISO: La profundidad de vaciado recomendada para todos los usos es de 5-1/2 pulgadas [140 mil metros]. La profundidad m nima de concreto es de 5 pulgadas [127 mil metros] con la m nima profundidad del compartimiento de cableado de 1-3/4 pulgadas [44 mil metros].
CONFIGURACI N SOLO SERVICIO MULTI-SERVICIO (ENERG A) MULTI-SERVICIO (DATOS)
VOL MENES DE LA CAJA DE PISO EN 5 PULGADAS [127 MIL METROS] DE ALTURA M NIMO 67.0 IN [1098 CM ] 34.0 IN [557 CM ] 31.0 IN [508 CM ]
VOLUMEN DE LA ADICI N PARA CADA PULGADA [12.7 MIL METROS] DE ALTURA 6.5 IN [107 CM ] 3.0 IN [49 CM ] 3.5 IN [57 CM ]
HUBBELL DE M XICO garantiza este producto, de estar libre de defectos en materiales y mano de obra por un a o a partir de su compra. Hubbell reparar o reemplazar el art culo a su juicio en un plazo de 60 d as. Esta garant a no cubre desgastes por uso normal o da os ocasionados por accidente, mal uso, abuso o negligencia. El vendedor no otorga otras garant as y excluye expresamente da os incidentales o consecuenciales inherentes a su uso. Av. Insurgentes Sur # 1228 Piso 8 Col. Tlacoquemecatl del Valle HUBBELL DE M XlCO, S.A. de C.V. Tel.:(55) 9151 - 9999 M xico, 03200 D.F.
See product label for lamp type. The nearest illuminated surface must be at least 0.5m from the front of the fitting. This luminaire is not suitable for covering with ...
to find the latest list of compatible dimmers when using multiple ULTRA RT6 recessed kits ... Important safety information - read all instructions before installation.
Verify mounting location before drilling any holes, the area must ... This transmitter must not be co-located or operating in conjunction with any other antenna or ...
Both Green and Green/Yellow (Ground) leads must be tied together and connected to ... If so, the supplied "standby power" label should be placed next to the ...
household or commercial waste. Aurora does not levy any WEEE disposal charges to its customers for affected WEEE related products. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate any such
Ver Figura 2 para tapas rectangulares de series 24GCCVRxx y 24GCCVRxxC para uso con cajas de piso de series CFB2G25, CFB2G25CR, CFB2G30, CFB2G30CR, CFB4G25, CFB4G25CR, CFB4G30,. CFB4G30CR y CFB4G30CI. Ver Figura 3 para tapas rectangulares de series 2
NOTICE: For installation by a qualified electrician in accordance with all national and local ... Unused conduit ports should be left covered with closure plugs [4].
ACTION Directive to initiate a briefed attack sequence or maneuver. ACTIVE An emitter is radiating. ADD () Directive call to add a specific (system) or (electronic ...
TOYOTA RD CENTER, 5(2) (1968) 1-30; (Part 2). ibid, 5(4) (1968) 1-35. 34. ...... 1460. 1670. Plastic forming. Reduction of area. Elongation. Vickers hardness ...... P. Clement, J.P. Angeli and A. F'ineau: Shot crack behaviour in nodular cast iron ...
For design engineers taking metal fatigue into account for the first time, the related ... and engineers based at other academic institutions, research institutes and companies: ..... 7.6 What Happens to the Fatigue Limit of Bearing Steels without.
Tournevis pour vis Phillips ... de la tête de le vis contre le sens des aiguilles d'une montre. .... faire pivoter d'un quart de tour jusqu'à ce qu'elle se bloque.
15 nov. 2013 - Be sure to install the Mid-Size Plate with Duplex Receptacle in accordance with the National Electrical Code (NEC) and local codes. Figure 1 â Front View. Figure 2 â Back View. Concealed Wiring. (hidden in wall). Flat Screen TV. Co
24 juil. 2013 - horizontal, le vissage de la niche dans l'encadrement, l'installation de la cloison sèche (ou la planche d'appui dans le cas d'une douche), ...
Hubbell box Cat.# RR1500 (Fig.4) or ... Black or Red to Brass Screw. 3. For side wire: use #14 to #12 ... Mount the device to the box. * Separate power feed is ...
BETWEEN THE SUPPORT COLLAR AND TILE. Adjust height of cover support collar flush to just below the finished floor. Cover support collar is adjustable for.
Sufficient air is needed for proper combustion and exhausting of gases through the .... gap between bottom of housing and ceiling material. Pound nails tight.
Apr 25, 1997 - This publication standardizes air-to-air, and air-to-surface, ..... Informative indicating a turn to a hot aspect relative to a threat/target. INDIA.
Wire the floor box by removing (2) #6 flat head screws(d) to seperate sheet metal base(f). Use 1/2" knockouts e1(power) and/or e2(data) for side wiring. OR use ...