• Long life (50,000 hour rated life) • 5 year warranty • IP30: Dry location rated
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING/AVERTISSEMENT RISK OF ELECTRIC SHOCK • Turn power off before inspection, installation or removal. • Properly ground electrical enclosure. RISK OF FIRE • Follow all NEC and local codes. • Use only UL or IEC approved wire for input/output connections. Minimum size 18 AWG (0.75 mm2). • Do not install insulation within 3 inches (76 mm) of luminaire top.
RISQUES DE DÉCHARGES ÉLECTRIQUES • Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire. • Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique. RISQUES D’INCENDIE • Respectez tous les codes NEC et codes locaux. • N’utilisez que des fils approuvés par UL ou IEC pour les entrées/sorties de connexion. Taille minimum 18 AWG (0.75 mm2). • Maintenir une distance de 76 mm (3 pouces) entre le luminaire et l’isolant.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Unit Installation Hook under bridge
Short side
Long side
1
Carefully unpack unit and properly inspect for defects before installing. Wear work gloves to prevent dirt and oil from being transferred to the luminaire. If cleaning is needed, use gloves and a dry cotton cloth. It is not recommended to use hazardous chemicals.
2
On the long sides of the fixture, fasten four mounting clips with screws.
imagination at work
3
On both short sides of the fixture, hook a mounting clip under the bridge and fasten to the fixture.
WARNING/AVERTISSEMENT Risk of Fire. Do not install insulation within 3 inches (76 mm) of luminaire top. Risques d’incendie. Ne pas installer d’isolation à moins de 76 mm (3 pouces) au-dessus du luminaire.
Safety cable hole
Press clip to fasten to T-bar
Insert LED Fixture into T-bar ceiling grid. Press clips to fasten to T-bar. To ensure a consistent appearance, align fixtures in the same orientation throughout the ceiling pattern.
5
Secure safety cable to connection hole as needed to meet local seismic requirements. Safety cable and method of attachment to the building provided by contractor according to local building codes.
A
To dimming controller
LED Driver
AC line
Connect the black (line), white (neutral), and green wires of the AC line to the terminal block. When connecting dimming controller, wires must be run through a separate knockout hole equipped with cable gland. Use smaller knockout holes for dimming and supply connections. Replace electrical enclosure cover. Remove protective film from the face of the luminaire.
Remove electrical enclosure cover. Carefully remove knockout for AC line input wires. Install listed electrical fittings in the knockout holes for wire protection.
B
0-10 Volt Dimming
BLU/WHT
BLU/WHT
BLK/WHT
BLK/WHT
YEL GRY VIO VIO/WHT
7
6
0-10V 0-10V +
To 0-10V Dimmer
LED Driver
4
DALI Controller
YEL GRY VIO VIO/WHT
DALI/Prog DALI/Prog
To DALI Controller
Optional Installation: 0-10 Volt Dimming or DALI Lighting Controller Option for Step 7: Follow Diagram A for 0-10V or Diagram B for DALI. Run wires from controller through a different knockout than the AC input wire. At output side of LED Driver, make appropriate connections using twist-on wire connectors. Follow lighting controller installation instructions.
Conforms to the following standards:
Specifications Input Power (W) Input Current (A) Input Voltage (VAC) Input Frequency (Hz) Power Factor Typical Lumens Efficiency CCT CRI Control Ceilings Life Dimensions (with electrical enclosure ) Weight Environmental Operating Temperature Range Environmental Rating Environmental Storage Temperature Range
to find the latest list of compatible dimmers when using multiple ULTRA RT6 recessed kits ... Important safety information - read all instructions before installation.
household or commercial waste. Aurora does not levy any WEEE disposal charges to its customers for affected WEEE related products. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate any such
13 janv. 2016 - RISK OF ELECTRIC SHOCK. CAUTION. RISK OF .... Verifique que el voltaje de alimentación sea correcto; compárelo con la información de la ...
periodically clean the reflector and refractor with a non-abrasive cleaner. TROUBLE SHOOTING. In the event your fixture fails to operate properly, first check that:.
24 mai 2013 - CK. +. -. RED. BLA. CK. RED. GREEN. N. O. TE: The SPD. T switch shown to change the LED colour is not included with the LED . Page 1 of 2 ...
purpose, please contact your nearest representative. .... dimensions sont sujettes à modifications sans préavis. GARANTIE ET .... Remarque: Un joint souple et résistant doit être posé ... inclus) pour assurer l'étanchéité entre ce dernier et la ...
Sufficient air is needed for proper combustion and exhausting of gases through the .... gap between bottom of housing and ceiling material. Pound nails tight.
PE receptacle and rotating it until the word âNorth'' is directed toward true north. Lower PE receptacle to firmly seat it in this position. Then install PE control.
This luminaire is IP44 rated and is suitable for bathroom zones 1 and 2. â¢. Class I, mains voltage, These luminaires must be earthed. â¢. These downlights must be ...
All other trademarks are the property of their respective owners. Information provided is subject to change without notice. All values are design or typical values ...
IMPORTANT INSTALLATION INFORMATION ... IP65 rated luminaires are protected against dust and jets of water. ... Waste Electrical & Electronic Equipment Regulations (WEEE) requires that any of our products showing ... environment or human health from u
at least 24 hours before conducting a long-term test. STEP 1: When AC power is applied, the charging indicator light is illuminated, indicating the battery is being.
... A COPY FOR THE USER / MAINTENANCE ENGINEER FOR FUTURE REFERENCE ... a minimum of 3 luminaries are required on each dimmable circuit due to ... working environment or installation not according to the current edition of the ...
1. SATURNE. Suspension – Pendant. Hervé Langlais. 2014. La sphère lumineuse est ici prétexte au ... la suspension Saturne devient le reflet de votre vision.
See product label for lamp type. The nearest illuminated surface must be at least 0.5m from the front of the fitting. This luminaire is not suitable for covering with ...
By itself or as an arrangement, the triangular module. Tétra can shape your own creation with light. ... VERRERIE – GLASS. Drop Paper® 100. Drop Paper® 101.
