3. The coach will have a bayonet-type fitting with a cap (Fig. 3). Remove the cap.
Tools required:
• 10” Hacksaw • ABS Glue • Sandpaper
Installation
1. Female cam lock (Fig. 1) affixes to terminal end of coach plumbing and replaces bayonet fitting.
Cap Fig.3
4. Cut off the 4 tabs with a hacksaw (Fig. 4).
Fig.1
2. Male cam lock fitting comes pre-installed on the end of the 4:1 compression hose (Fig. 2).
Fig.4
NOTE: A 10” mini Hacksaw is recommended for getting a close cut.
Fig.2 lci1.com
(574) 537-8900
2
CCD-0001593
Rev: 07.11.18
Waste Master Hose
Aftermarket Manual
5. Use sandpaper to get a smooth surface and to remove any burrs remaining after cutting off the tabs (Fig. 5).
7. Insert the male cam lock cap (Fig. 7A) into the female cam lock with the arms on the female cam lock in the open position. 8. Lock the cam lock cap in place by pushing the arms down against the sides of the female cam lock.
Fig.5
A
6. Apply the ABS glue to the pipe at the coach. Apply ABS glue to the female cam lock fitting and apply another swipe of glue to the pipe at the coach (Fig. 6). Take the cam lock fitting and push it on the pipe, turn approximately 90 degrees to the final position (Fig. 7) and hold in place for 30 seconds.
Fig.7
9. To install hose, remove male cam lock cap and insert the male end of the hose and lock into place.
NOTE: The waste pipe is ABS pipe. Use approved glue for ABS piping. Do not use glue for PVC or CPVC piping. Allow 15 minutes for the glue to set before proceeding.
Fig.6
lci1.com
(574) 537-8900
3
CCD-0001593
Rev: 07.11.18
Waste Master Hose
Aftermarket Manual
Notes
Manual information may be distributed as a complete document only, unless Lippert Components provides explicit consent to distribute individual parts. All manual information is subject to change without notice. Revised editions will be available for free download at lci1.com. Manual information is considered factual until made obsolete by a revised version. Please recycle all obsolete materials and contact Lippert Components with concerns or questions. lci1.com
transparent 15 mm transparent polycarbonate, which gives a fantastic panoramic view and very nice design. These doors are standard delivered with a stainless.
acquisition speeds up greatly and gives you greater sensitivity to see faint out-of- ... Camera Settings â Allows you to set the fan speed to high, medium or low for.
Crystal-Clear pendeldeuren types CCE-CCD zijn uitgevoerd met deurbladen ... Crystal Clear-Pendeltüren Typs CCE-CCD sind ausgeführt mit Türblätter in.
cm2, which is based on the energy in the associated wavelength band, may be more appropriate ..... When, for instance, A4 size paper (whose short side length.
the receiving element (PSD or CCD) and coupled with linearization and additional signal ... There is no other information that the PSD element can provide.
The light is reflected off the target and focused via an optical lens system onto a light sensitive device built into the sensor head, called a receiving element.
time, the installer will inform you that your free upgrades have expired. ..... If the image does not fit within the screen area, click the Zoom Out button on the ...... therefore suppresses âimpulsiveâ noise, such as hot pixels and cosmic ray hi
Use a previous version of the Product if you have received a replacement disk ...... to below 1.0 and adjust until you are happy with the effect in the Preview Image. ...... Often images can be noisy â no matter how good the camera is, it always ad
Sep 24, 1999 - The following is a list of the current part numbers for the KAF-0400 series .... Please Fax or Email the following information: ⢠Name. ⢠Address.
Jan 3, 2000 - it an electron generated by thermal motions within the CCD itself). We have to be ... ative collecting power of the device as a function of wavelength. QE curves shown in ... If you ever have a chance to hold a CCD, you will easily see
Accordingly, this CCD is suitable for such applications as security cameras and cameras for vehicles, which typically involve high contrast between the scene's ...