640010-00 Rim Exit Device Dispositivo de salida con montura Appareil de sortie du rebord
Installation Instructions Instrucciones de Instalación Notice d’installation
#10-24 ¹⁄₄"-20
³⁄₄" (19 mm)
Dogging Key
Llave de trinquete
Œillet vissé
Use to lock down pushbar Utilícela para asegurar hacia abajo la barra de empuje Utilisé pour verrouiller la barre antipanique
OR O OU 299
! 1
299-F
If sexbolts are in box, see Sexbolt Preparation on back page Si los pernos macho-hembra se encuentran en la caja consulte preparación de pernos macho-hembra en la página posterior Si les colonnettes sont dans la boîte, voir la préparation de colonnettes au verso de la page
2
Mark 2 Slots Marque 2 ranuras Marquer deux fentes
Draw Exit Device Centerline ( ) Saque la línea central del dispositivo de salida ( ) Tracer l'axe du dispositif de sortie ( )
299 OR O OU
RHR
LHR
299-F For more information on strikes shown below, go to: Para mayor información sobre cerrojos que se muestran a continuación, vaya a: Pour obtenir plus d'information au sujet des gâches illustrées ci-dessous, aller à:
www.allegion.com/us
40" (101.6 cm) from finished floor 101.6 cm desde el piso terminado 101.6 cm à partir du plancher fini
RHR 1439
264
1606
1609
3
5
Mark 4 Holes Maque 4 orificios Marquer 4 orifices
LHR
Metal #25
Wood
¹⁄₈" (3 mm)
4
Metal
Métal
#10-24 OR O OU Madera 1" (25 mm) deep/profundidad/ profondeur
Draw Vertical Centerline ( ) Sacar línea central vertical ( ) Tracer l'axe vertical ( )
Center point on plastic template Punto central en la plantilla de plástico Placer la pointe de centrage sur le gabarit de plastique
RHR
Metal
Metal
Métal
#25 #10-24 OR O OU
Wood
Madera Bois
¹⁄₈" (3 mm) X 1” (25 mm)
7
Parallel with door edge Paralelo en el borde de la puerta Parallèlement au bord de la porte
If Installing Trim, Go To Trim Instructions Si instala la moldura, vaya a instrucciones de la moldura Pour l'installation d'une garniture, voir Trim les instructions de Moldura garniture
Garniture
8
10
Prepare 2 Holes* Prepare 2 orificios* Préparer 2 orifices* Metal
Metal
Métal
#7 ¹⁄₄" x #20 OR O OU
Wood
Madera Bois
¹⁄₈" (3 mm) X 1” (25 mm)
*If using trim, holes may have been drilled already *Si utiliza molduras, los orificios ya deben estar perforados *Les orifices peuvent être déjà percés si vous utilisez une garniture
9
Thru-bolting Trim Moldura apernada Vissage transversal de la garniture
If Necessary, Cut Device Si es necesario, corte el dispositivo Couper le dispositif si nécessaire
Surface Mount Montaje de la superficie Montage en surface
Install Support Screw Instale el tornillo de soporte Installer les vis de support 299
299-F OR O OU
Metal
Metal
#25
Métal
#10-24
Metal/Metal/Métal
Wood/Madera/Bois
13
Install Required Support Screws Instale los tornillos de soporte requeridos Installer les vis nécessaires de support
¹⁄₈" (3 mm)
Si los pernos macho-hembra se encuentran en la caja durante los pasos 6, 8 y 11 prepare los orificios Si les colonnettes sont dans la boîte, préparer les orifices pendant les étapes 6, 8 et 11
Wood/Madera/Bois
14 b
Colonnette Préparation
If sexbolts are in box, during steps 6, 8, & 11 prepare holes and install them as shown below
Metal/Metal/Métal
Position pushbar guide Posición en la guía de la barra de empuje Guide de positionnement de la barre antipanique
Full mortise, half wrap, cover system, pin and barrel, with electrical power transfer. Customer Service Servicio al cliente Service à la clientèle. 1-877-671-7011.
4210 Cush Series. Installation Instructions. 4. T-25. T-27. Attach cover with fasteners provided ... "Normal" de una puerta abierta a 90° es de 5 hasta 7 segundos,.
The use of the word partner does not imply a partnership relationship ... Guidelines for Using 1200 Series Lightweight Access Points 1-3 .... English Translation B-10 ..... point attempts to download new operating system software if the software ....
Low Power Condition for Autonomous Access Points 3-6 ... Running the Carrier Busy Test 3-14 ..... Cisco Aironet 1130AG Series Access Point (models: AIR-AP1131AG and ..... this manual will result in user exposure that is substantially below the FCC ..
for SIUDI 1bis and SIUDI 2, don't forget to remove the CMS chip if you want to ... As with any other DMX controller, keep aside an independent backup system, ... In this manual, you will find informations and hints about the several possible.
Convert. Produces a specific. 8kB binary file. Convert the sequences: fill_eeprom.exe. Each text file ... adresse_fin_lo: byte; adresse_debut, adresse_fin: word;.
May 4, 2008 - These tables are generally not accessible through queries external to ... accessed are marked under the Query column of the following table.
replot "min.asc" using 1:2 with points to plot the position of the dip of SPR ... If that is not the case, modify the source code accordingly (see the idComDev= line).
in diameter. The number after the dash indicates the total length of the bolt's shank in eighths of an inch, or inches and eighths for bolts more than 1 inch long. In.
Graphics Port (AGP) interface provides a dedicated path for memory-intensive graphics ... 2x mode 3D graphics. .... CPU utilization is restored to normal levels when the ... For more detail information, please visit the web site of Microsoft.
5 Slide Rail Assembly Procedure . .... on the regulatory label on the bottom of the chassis and does not have any vent holes on the ... Reset: The small hole to the left of the console port is used to reset the system to the factory .... in accordanc
you high-speed wireless access for your home or office. ... 802.11g compatible wireless routers, access points, and ... Outdoors: Up to 1312ft (400 meters).