Mounting surface and no wall studs or other objects to block the back of the speaker. 2. Remove the inner cardboard disc from the supplied template/paint mask and keep it for later. Use the outer portion as a template to mark the cutout hole size and location for mounting the speaker. 3. Use a drywall or keyhole saw to.
2-Way Ceiling Speaker OWNER'S MANUAL - Please read before using this equipment.
INSTALLATION
paint mask and replace the grill. Paint Mask
PREPARING THE LOCATION ;}i -ilmpor^ant
To mount your speaker, you need the following items (not supplied, available at your local electronics store). drywall or keyhole saw wire stripper
CONNECTING THE SPEAKER WIRES
Phillips screwdriver
Your local electronics store sells a wide selection of speaker wire. We recommend you use wire that is color-coded or marked on one side to help you connect the wire
pencil or marker
18-20 gauge speaker wire 1.
Be sure the mounting surface is Between 3/8" (9.5mm) and 1 1/4" (31 mm) Thick, with at least a 2 3/4
(69mm) clearance behind the Mounting surface and no wall studs or other objects to block the back of the speaker. 2.
correctly
1. Route the speaker wire to the speaker from the receiver. II
2. Separate about 4"(101mm) of Speaker wire at each end.
Remove the inner cardboard disc from the supplied template/paint
6cra (I/-I*)
mask and keep it for later. Use
the outer portion as a template to mark the cutout hole size and
location for mounting the speaker.
101cm (•!">
3. Using a wire stripper, remove about 1/4"(6mm) of insulation from each wire. Then twist the ends of each wire. 4. Connect the marked wire to a red Speaker terminal by pressing the release tab, inserting the wire into the hole, and then releasing the Tab. Repeat this
3 NOTE Z Do not paint the speaker element. We recommend you spray-paint the grille so paint does not block the holes.
3.
Use a drywall or keyhole saw to cut the hole, a
PREPARING THE SPEAKER If you choose to paint the frame and grille, paint them and let them dry before you connect the speaker wire or mount
procedure to connect the unmarked-wire to the balck terminal.
5. Connect the marked wire coming from the speaker to the left channel of the receiver's positive (+) terminal. Then connect the unmarked wire to the left Channel of the amplifier's negative (-) terminal.
the speaker.
MOUNTING THE SPEAKER
To remove the grille for painting, insert a
1. Remove the grill to expose the
paper clip into one of the grille openings
then pull up. Or, you can carefully twist
the plastic frame back and forth until the grille edge becomes exposed, then lift
the grille to remove it.or use the grill remover to remove the grille.
mounting screws. 2. Be sure the mounting tabs are turned in, allowing the speaker to fit into the hole. Then insert the speaker into the mounting hole. 3. Use the four screws to tighten the mounting tabs to the wall or ceiling. Be careful not to
over tighten the screws. 4. Replace the grille.
Z
NOTE
yA
Avoid routing the speaker wire near electrical wires. Do not nail or staple the speaker wire.
Carefully remove the dust cloth from behind the grill and replace it after
Mounting Tabs
you are finished painting. You can also paint the frame to match
your wall or ceiling. To prevent paint from entering the speaker, remove the grill and insert the supplied cardboard paint mask. After the paint is dry, remove the
fUlONOPEICE
To remove the speaker from the wall or ceiling, loosen the screws only far enough to remove the speaker. This will prevent loss of the mounting tabs.
If an icon appears at the end of a paragraph, go to the box on that page with the corresponding icon for pertinent information. Q - Warning 1 - Important. ï¬ - Caution _ - Hint. E - Note. B NOTE l3. Do not paint the speaker element. We recommend you
Measurement hold to temporarily store a trace. Frequency can be set using either Start/Stop or Center/Span frequencies. Measurement can be Return Loss [dB], ...
Coloque las tiras adhesivas dentro del marco de los parlantes. Inserte la rejilla de .... necesitará tener acceso al interior de los parlantes durante la instalación.
yellow LED on the left side of the RJ45 port illuminates when a valid connection is in place and blinks when data is being transferred. The LED on the right illuminates in amber color when a. 10Base-T connedion is established and illuminates green wh
Connect BLACK wire from light kit fitter to BLUE wire from fan. Make sure that molex connections snap together completely. Attach glass shade to light kit fitter ...
Fix the base to the wall or ceiling as required. ... there will also be an un-switched permanent Live which is connected to the terminal marked L1 at this point the.
Desserrez les vis de la platine et retirez la platine. 4. Fixez la base au mur ou au plafond, selon le cas. Faites attention aux solives, conduites d'eau et aux câbles ...
Desserrez les vis de la platine et retirez la platine. 4. Fixez la base au mur ou au plafond, selon le cas. Faites attention aux solives, aux conduites d'eau et aux ...
less technology Speaker with your Android device. c. For all other Bluetooth® wireless technology enabled devices: i. Follow the instructions that came with your ...
Here's the promised solid-state landing light flasher. By Jim Weir. The top view of the chassis. In the January issue, I went into some detail on how to make a.
Jan 19, 2009 - Use different solid meshers such as Tetrahedron Filler, OCTREE .... FEM Solid or FMD provides you the tools to create solid meshing of component ..... MeshPart : lets you specify the mesh to extrude, multi selection is ... For example,
Replacez le diffuseur et la collerette. 9. Mettez sous tension. Protection de l'environnement (D.E.E.E.) â N° d'inscription DEEE d'Aurora en Grande-Bretagne ...
statistical analysis by the CEA CosmoStat group . These will be applied to event reconstruction. 3 and scientific image analysis. Access to existing data (e.g. from ...
Bringing something ancient back to fashion, this is what. Pauline had in mind for ... diminuée à l'installation. The height can be ajusted to less during installation.
Apparence finie. Thank you for purchasing this fine window treatment proudly constructed by Springs Window Fashions. Your drape has been custom-made to your personal specifications with the highest standards of quality and craftsmanship. We have conf
The Red LED on the sensor indicates 'No motion detected', the green LED will show when movement is detected. The function of this fitting can only be used to ...
N'installez pas les enceintes sur un plan incliné. • N'installez pas votre ... Bien que ce système soit doté d'un blindage magnétique, il est possible que l'image de ...
'The Auto Speaker Setup kit is the optional accessories designed for use with ... information from a series of test tones emitted from speakers and can adjust the ...
SINGLE PAIR DIRECT. ENGAGE WHEN USING ONE PAIR OF LOUDSPEAKERS TH l_l. [. * @@. _ @@. L INPUTS R. L_l l_l ... planned system of impedance matching volume controls, allowing you to get most out of your amplifier. If you are unsure, consult a professio
receipt and register your Zagg Speaker Case on our website (purchases made on our website are automatically registered). Replacement products must be ...
3. Make sure Fan is ON and Bluetooth® wireless technology enabled device is located within 10 meters (approximately 33 feet) of the Speaker/Fan. 4. Pairing your Bluetooth® wireless technology enabled device with the Speaker: a. For iPad/iPhone/iPod