Improper Installation of Ratchets and/or SKYLENS could result in SKYLENS opening during freefall and possible loss of SKYLENS . SKY SYSTEMS USA, Inc. is not responsible for lost or damaged equipment due to improper installation of SKYLENS and/or Ratchets.
Outside
Left Ratchet
TM
WARNING PLEASE READ!
The Ratchets can be Identified by a small letter indicating right (R) or left (L) on the inner side of the ratchet (the side with the two posts). If your ratchets were purchased recently they may be labled in Ink on the outside face also.
TM
SKY SYSTEMS USA, INC offers no written or implied warranty to this product in terms of safety or protection. Skydiving is a dangerous sport and participation in the sport can possibly lead to injury or even death. No helmet can fully protect a person from serious injury to the head, neck and/or spine. Use your head and skydive safely.
PROPER RATCHET INSTALLATION
Outside
Changing the SKYLENS TM
1) To access the SKYLENS TM you must remove the sideplates. To do so remove both screws using a 5/64 allen wrench (fig. A). 2) With both sideplates off you can remove the lens and ratchets as one piece. Place the old SKYLENS TM with ratchets next to the new SKYLENS TM. 3) If the ratchets are still in good condition you are going to switch them over to the new lens. To avoid confusion change only one at a time. MAKE SURE THE RIGHT RATCHET GOES OVER THE RIGHT EAR AND THE LEFT GOES OVER THE LEFT EAR. 4) To remove the ratchets from the SKYLENS TM simply pry the flexible tab back which holds the ratchet to the lens. 5) To place the ratchets back on the lens follow set of directions on right (#2 Ratchet Installation). 6) With both ratchets installed in your new SKYLENS TM, the lens is now ready to go back in the helmet. There are two round holes in each ratchet pocket on the helmet (fig. B). The two posts of the ratchet need to be placed in these holes (fig C). 7) Once you place the ratchet into the pocket put the corresponding sideplate over top and line up the holes. Put in the screws by starting a few threads on one. Then screw the second screw in a few threads. Once both screws are in you can begin to screw them all the way in. DO NOT OVERTIGHTEN THE SCREWS because it will prevent smooth opening and closing of the lens. 8) With one side secure, you can now repeat the process on the other side.
Ratchets should be on correct side of helmet and spring should point forward.
2
Ratchet Installation
1) It is very important that ratchets are installed properly and on their correct side of the helmet. Failure to do this could result in SKYLENS TM opening in freefall and possible loss of lens. SKY SYSTEMS USA, Inc. is not responsible for lost or damaged equipment or any injuries resulting from improper installation of ratchets. 2) Make sure you can identify the left and right ratchet. The left ratchet goes over your left ear and the right should be over the right ear. All ratchets are marked on the inner side with an “L” or “R” embossed in the plastic. Some may also be labled in ink. 3) When installing ratchets the spring should always point forward to the front of the helmet. (See diagram above) 4) With ratchets on their respective side insert square of ratchet through lens from the inside out. Both tabs on the ratchet need to catch the lens. See diagram above.
REPLACEMENT PARTS AVAILABLE: L
R
1
Inside
TM
TM
Right Ratchet
Inside
REPLACEMENT
Front of Helmet
For the following models:
TM
Sideplates
WARNING
WARNING
Ratchets
Sky Systems USA, Inc offers no warranty whatsoever with this product in regards to safety or performance. Skydiving is a dangerous activity which may result in serious injury or death. USE THIS PRODUCT AT YOUR OWN RISK!
Screws
1407 Flightline Blvd. Unit 13. Deland, FL 32724 (386.734.6001)
rating plate is located on the bottom of the control panel, at the far right, .... SIDE VIEW. *Without .... parte inferior del montaje del panel de control, en el extremo.
Los números de productos seguidos de ... without notice, as specified in the Price Book. ..... Debido a la naturaleza de las instalaciones bajo cubierta, Kohler.
... work or if your local electrical code requires professional installation! ..... Allineare i quattro fori per viti sul modulo ottico con i quattro fori del mozzo del ...
flujo en un sistema de ducha existente, verifique la compatibilidad antes de su ducha. No utilice este producto de bajo flujo Kohler con una válvula de ducha ...
Twist ends of stripped wires together as per schematic. ⢠Twist on wire connectors clockwise until secure. ⢠Connect green ground wire to bare wire, and mount to ...
or Bare Copper (Ground Wire) from outlet box. Twist wires together clockwise and secure with wire connector (E). Installer Tip (2): If ground wire is not available in outlet box, then secure Bare Copper (Ground Wire) from fixture to ground screw (F)
when the door is open or through the window of glass door models. GRILLE .... socket, turn the 3/8" hex bolt clockwise to raise the unit or counterclockwise to ...
The oven door must be open to view the rating plate. Refer to the illustration .... produzcan heridas graves o incluso la muerte si no se siguen las precauciones.
Cablofil, the inventor of wire mesh cable tray is a revolutionary cable management system that provides exceptional strength combined with the flexibility to adapt easily to field requirements. installation is easier since wire mesh requires fewer pa
O-ring over the faucet supply hoses and place into the groove in the underside of the faucet body (not shown). For all installations: Feed the faucet supply hoses ...
antenna of a different type or with a gain higher than 2.14 dBi is strictly ... every application using the MGM12P will need to perform the radio EMC tests on the ...
immediately, protect the end connector with tape or other shielding material. ... NOTICE: Do not pinch, nail, wedge, or use undue force when handling the silver crossover ... If additional equipment is to be connected downstream of this device,.
minimum of 69¹âµâââ" (177.6 cm) high, 22¹âââ" (56.0 cm) wide, and. 21â·ââ" (55.5 cm) ... is open air, allow a minimum of 7â·ââ" (20.0 cm) above the refrigerator.
Kohler Co. reserves the right to make revisions in the design of trip levers without notice, as specified within the Price Book. Adjustable. Wrench. 1017838-2-C. 2.
VONN highly recommends to use a qualified, licensed electrician to install the fixture. VONN recommends to install the fixture on its own independent circuit. Do not install the fixture on the same circuit with other appliances, or. HVAC systems. DO
6 On the Notification Service Plugin page, accept the default (1840) or enter a port for the plugin, and .... The BMC Impact Solutions Documentation is a .pdf of all manuals that support the .... mode of the installation program, in this case, silent
design des robinets et ceci sans préavis, comme spécifié dans le catalogue des prix. Clé à molette. Clé à sangle. Joint d'étanchéité pour filetage. Mastic de.
Distance between centerline to holes 12-13/16" (324.65 mm). Distance ... and the floor line with the floor of the cutout. Tape it into ... Floor Line of Cutout Opening.
