Usando sólo dos tornillos (3 tornillos del paso 3), instale las bisagras en el capó. Asegúrese de que los tornillos estén bien apretados (15-20 in-lbs). 6).
AGPCC34W INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION INSTRUCCIONES DE INSTALACIÓN
AGPCC34W INSTALLATION INSTRUCTIONS 1)
Remove the glass panels from the package by removing the (6) retention clips.
2)
Open up stainless panel of the hood.
3)
Remove and keep the (3) screws at each hinge (will reuse for the glass panels).
4)
Install the glass panel by using the outer most holes to mount the panel hinges.
5) Using (2) of the screws used in step 3, install each hinge onto the hood. Make sure that the screws are tight (15-20 in-lbs). 6)
Repeat for the other glass pane.
AGPCC34W INSTRUCTIONS D’INSTALLATION 1)
Enlever le panneau en verre de l’emballage en enlevant les (6) clips de fixation.
2)
Ouvrir le panneau inox de la hotte.
3) Enlever le panneau inox et tenir les (3) vis de chaque charniere (afin de les réutiliser pour le panneau en verre). 4) Installer le panneau en verre en utilisant les trous extérieurs (ceux aux extémités du support) afin de monter les charnieres du panneau en verre.
5) Utilisant seulement 2 des vis ( des 3 vis du point 3), installer chaque charnière sur la hotte. Etre sur que les vis soient bien fixées (15-20 in-lbs). 6) Répéter chaque passage (du point 1 au point 5) pour le second panneau en verre à monter.
AGPCC34W INSTRUCCIONES DE INSTALACIÓN 1)
Quite el panel de cristal del paquete mediante la eliminación de las grapas (6).
2)
Abra el panel de acero inoxidable de la campana.
3) Retire el panel de acero inoxidable y mantenga (3) tornillos de cada bisagra (para su reutilización para el panel de cristal). 4) Instale el panel de vidrio utilizando los orificios externos (los que tienen el apoyo extémités) para montar las bisagras del panel de vidrio.
5) Usando sólo dos tornillos (3 tornillos del paso 3), instale las bisagras en el capó. Asegúrese de que los tornillos estén bien apretados (15-20 in-lbs). 6) Repetir cada paso (del punto 1 al punto 5) para el segundo montaje del panel de vidrio.
The motor will restart when it cools down. If the motor continues to shut off and restart, have the hood serviced. 8. For best capture of cooking impurities, the ...
DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result. 4. Use an ... Long duct runs, elbows and transitions will reduce the performance of the hood. .... water after exposure and wipe dry with a clean cloth.
Rotate back of box up slightly and insert exhaust end down into opening. ... air tight. ⢠Use 6 - #10 x .625â screws to secure recirculation box to cabinet base. 6.
needed for the insert or power pack electrical connection. ... Consider the shape and size of the insert or power pack to determine the configuration of the custom ...
NOTE: If need be, use a rubber dishwashing glove to add grip when removing the bulb. For details on cleaning, see instructions included with insert or power ...
Cut the hole in the bottom of the custom hood. (See figure 4.) Reinstall the main liner plate to the base of the custom hood and secure it with 5 screws for liner ...
Main liner plate should be positioned in custom hood as far rearward as possible. Using a pen, mark the outline of the future hole for the power pack (or insert).
The LED ring (L1) flashes blue at a speed ... L1: LED Indicator Ring Signalling crown: - Hood in standby: .... Use duct tape to seal the joints between ductwork.
Use an extinguisher ONLY if: 1. You know you have a Class ABC extinguisher, and you already know how to operate it. 2. The fire is small and contained in the ...
smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. b) Always turn hood ON when cooking at high heat or when flambeing ...Termes manquants :
If the flames do not go out immediately EVACUATE AND CALL THE. FIRE DEPARTMENT ..... Align the center notches of the bracket and the centerline. Mark the ...
2.8 A suitable for use with solid state speed controls. ALL WALL .... Protection Association (NFPA), and the American Society .... The remote blower connects us-.
wet dishcloths or towels - a violent steam explosion will result. Use an ... This minimum clearance may be higher depending on local building code. ..... a local Faber distributor, contact us at (508) 358-5353 for the name of a distributor in your.
other enclosed space. ⢠DO NOT use 4" laundry-type wall caps. ⢠Flexible-type ductwork is not recommended. ⢠DO NOT obstruct the flow of combustion and.
for 5 seconds, until the remote control Indicator Light turns on. ... button on the hood control (see below). .... appartements avec cuisines contiguës, show-room,.
of the downdraft over the Overcounter Support Arms. Attach the .... Canada, including any non-UL or C-UL approved Faber rangehoods. 6. Repairs to the hood ...
1) You know you have a Class ABC extinguisher, and you already know how to operate it. 2) The fire is ... Determine which venting method is best for your application. Ductwork .... away, do it as far away from the hood's exhaust opening as possible.