FLUSH-FITTING “HALF-OUT” TECHNOLOGY
HIGHLY REINFORCED CARBON SHAFT
SMALL DIAMETER HUNTING SHAFT
CARBON IMPACT H . O . T. S Y S T E M
S mal l d i amet er car bon arrows used to be the standard a couple of years ago, and hunters everywhere loved them; very strong, amazing penetration, resistance to side wind, they had only one drawback: the overlapping point outsert. Now with Carbon Impacts new H.O.T. Technology you can have all the benefits including better penetration and resistance to wind drift without the need for an outsert.
2 2
FLUSH-FITTING POINT INSERT
Point outserts overlapping on the shafts are a thing of the past with the new H.O.T. System from Carbon Impact. In order to make a small diameter, highly reinforced
carbon shaft, the point insert is located half inside the shaft, and half outside. The outside part is flush fitting with the shaft and is of the exact same diameter. It is in fact a natural extension of the shaft. With the new HOT Shaft you get perfect broadhead alignment, easy removal from targets, and easy assembly (forget the nightmares of positioning an all-internal hidden insert!) HIGHLY REINFORCED SHAFT
Some may think that reinforcing a product as strong as a carbon arrow
woul d b e a wast e of t i m e, but improved strength is only one of the many benefits. A heavier reinforced shaft delivers a dramatic increase in kinetic energy for increased penetration, is more stable in flight, and makes for a quieter hunting bow. PROTECTIVE ROTONOCK SYSTEM
The HOT Shaft comes with a new design of the Rotonock System offering increased protection to the back of the shaft and easy tunability! 2 SPINES, 2 GRADES Straightness Weight
Variance
Yellow:
+
- .003”
55/65: 8.7 65/75: 9.6
+ +
Blue:
+
55/65: 8.7 65/75: 9.6
+ +
- .006”
3gr. - 3gr. 4gr. - 4gr.
3
• TOUGH XLT CONSTRUCTION OVEN CURED CRESTING – TOUGH!
• TOUGH CAMO FINISH • TOUGH CRESTING
BEST CAMO FINISH PERIOD! SEAMLESS XLT TECHNOLOGY
SUPER SMOOTH XLT FINISH
X LT
TECHNOLOGY
Unlike wrapping, XLT technology ensures total 360° consistency of the spine all around the shaft. There is no seam, so Fat Shaft XLT performs flawlessly and with consistency shot after shot. BEST CAMO – PERIOD!
This new camo technology not only provides superb “fit and finish” but also excellent durability, reduces friction noise on the rest and does not add any weight to the shaft! TOUGH
CRESTING!
Our factory applied cresting, adds virtually no weight to the shaft, is baked right onto the shaft for excellent durability and is protected by several layers of clear coat. Tough…and not expensive!
4
4 SPINES, 4 GRADES Straightness
Weight
+
- .001”
5000: 6000: 6500: 7500:
6.9 7.9 8.3 8.7
Orange: +- .002”
5000: 6000: 6500: 7500:
6.9 7.9 8.3 8.7
Green:
Variance
Yellow:
+
- .003”
5000: 6000: 6500: 7500:
6.9 7.9 8.3 8.7
Blue:
+
5000: 6000: 6500: 7500:
6.9 7.9 8.3 8.7
- .006”
+ + + +
1gr. 1gr. 1gr. - 1gr. + 2gr. + 2gr. + 2gr. + 2gr. + 3gr. + 3gr. + 3gr. + 3gr. + 4gr. + 4gr. + 4gr. + 4gr. -
• SUPER STABLE • SILENT FLIGHT • NOCK DOWN POWER • BUILT-IN ARROW STABILIZER
Perfectly Aligned Point Insert
WORLD’S FIRST BUILT-IN ARROW STABILIZER
Stealth XLT is the first arrow shaft in the world to feature a unique built-in arrow stabilizer. This vibration dampening device is factory installed at the optimum point within the arrow shaft in order to stabilize the arrow in flight quicker.
Seamless X LT Shaft Factory Installed
STABLE & ACCURATE!
The Stealth “built-in arrow stabilizer” has the unique ability to smooth out the arrow oscillation in flight, and helps optimize the Front-Of-Center (F.O.C.) balance, resulting in increased accuracy and penetration power.
D E A D LY S I L E N T !
The exclusive Stealth arrow stabilizer dampens vibration and noise of the shaft during flight and on the rest during the draw. If you have ever scared an animal during the draw or had one duck at the sound of your arrow then you can easily understand the value of the Stealth arrow technology!
3 SPINES, 2 GRADES
Built-in Arrow Stabilizer
Weight
Variance
Yellow:
+
- .003”
5000: 9.1 6000: 9.4 6500: 9.8
+ + +
Blue:
+
5000: 9.1 6000: 9.4 6500: 9.8
+ + +
Straightness
- .006”
3gr. 3gr. - 3gr. 4gr. 4gr. - 4gr.
5
• BEST VALUE FOR THE MONEY • SEAMLESS TECHNOLOGY 360° CONSISTENT SPINE
• FORGIVING SPINES • SUPER STRONG
VALUE
STRENGTH
The Trophy Hunter delivers all the qualities an archer could desire at an affordable price. If you put off buying carbon arrows because of the price, you’re wait is over. Now you can get the performance and durability of carbon at a price lower than most aluminum arrows.
When you only get one chance at success you want an arrow you can rely on, Trophy Hunter. Whether you hunt the toughest big game animals or the wary whitetail, they have the strength to meet any task.
PERFORMANCE
The unique seamless technology yields shafts you can count on to perform perfectly when you need them most. Trophy hunter shafts offer an economical choice without sacrificing any of the features you look for in a hunting arrow: accuracy, durability and speed.
6
EASY TO TUNE
Offering a forgiving spine, Trophy Hunter arrows are easy to tune with a large variety of bows, with only two spines. Trophy Hunters can be shot precisely by bows ranging from 45 lbs. up to 75 lbs. 2 SPINES, 2 GRADES Straightness Weight
Variance
Yellow:
+
- .003”
TH400: 7.8 +- 3gr. TH350: 8.1 +- 3gr.
Blue:
+
TH400: 7.8 +- 4gr. TH350: 8.1 +- 4gr.
- .006”
AN OUTSTANDING C O M P O U N D A R R OW
Fast, easy to tune and very strong, Carbon Youth arrows provide flat trajectory, plenty of rest clearance and outstanding durability. All of this adds up to an arrow that gets kids excited about archery and parents excited about affordability! 2 SPINES READY TO GO
Carbon Youth arrows come standard with Press Fit Nocks and can be fitted with either point inserts or target points.
For safety warning, see page 16.
AVAILABLE IN 2 SPINES: 3500 – 26” LONG 5500 – 28” LONG
INSERTS & POINTS
LOW PROFILE CARBON IMPACT PLASTIC VANES
(A) : 12 gr. (B): 60 gr. & (C): 80 gr. + 10 for Fat, Stealth, T-Hunter, and C-Youth. (D): 20 gr. for HOT Shaft.
Excellent shape memory, light, low profile and streamlined design, they come in 1.8" and 2.5" for target shafts, 3.8" for hunting shafts and 5" for crossbow bolts.
Fluo Yellow
Lime Green
PRESS FIT NOCK & ROTONOCK SYSTEM
Size
•
Length
•
Height
•
Weight
1.8" 2.5" 3.8" 5.0"
• • • •
1-3/4" 2-1/2" 3-3/4" 5"
• • • •
.385" .415" .475" .500"
• • • •
3 Grains 5 Grains 7 Grains 11 Grains
An activator applied to the vane base improves adhesion. Never clean the vane base before installing. Instant fletching glues (Cyanoacrylate) are recommended.
(E): Press Fit Nock – 13 gr. (F): Rotonock – 11gr. (Insert + nock)
Fluo Orange
Bright Blue
Black 1.8" 2.5"
White 3.8" 5.0"
Red
7
BEST CAMO FINISH
22/64" OUTSIDE DIA.– 325 GR. W/O POINT
HALF MOON OR FLAT NOCK
• SUPER TOUGH • FITS ALL CROSSBOWS • 12 GRAINS PER INCH Great Lakes Crossbow
FITS ANY CROSSBOW
U LT R A Q U I E T C A M O
EASY-OUT FLAT INSERT
T h e X LT 2 2 U l t r a b o l t i s f u l l y compatible with any crossbow. Featuring an outside diameter of 22/64" and available in 20" or 22" lengths, they are fully reinforced for amazing strength and have the weight you need.
This unique camo process fuses the pattern directly into the shaft and is protected by multiple layers of clear coating. Beautiful as well as functional, the smooth camo finish reduces friction on the bow making for a quieter shot.
The optional aluminum flat insert allows for easy arrow removal from targets with the help of any 8/32" component.
1 5 "
Featuring an outside diameter of 19/64" and available in 15" length, for a weight of 250 grains
C A R B O N
B O LT
X LT
without point, they are super fast, precise, strong, penetrating… and economical.
Caution is recommended as the 15" Carbon Bolt may not fit all crossbows due to its reduced diameter and weight.
SUPER FAST, SUPER STRONG, AND SUPER ECONOMICAL !
8
19/64" OUTSIDE DIAMETER – 250 GR. W/O POINT
BOWHUNTING PRECAUTIONS
SAFETY WARNING SHOOTING PRECAUTIONS 1. Inspect the arrow shaft – If carbon arrows are abused, hit by other arrows or slapped against hard objects damage to the carbon fibers could occur. Carbon Impact arrows should always be gently flexed and twisted end-to-end as well as visually inspected for delamination or splitting prior to each shooting. Warning: A damaged shaft could fail upon release and cause injury to yourself or others.
4. Dispose of any meat that might contain carbon splinters.
A S S E M B LY
Warning: Use only Carbon Impact brand components with your Carbon Impact shaft. Point inserts, nocks and nock inserts are specifically sized to match the shaft diameters. The use of components other than those marketed by Carbon
3) Select your draw weight in column A or B 4) Your correctly spined shaft is in the box at the intersection of the row selected in # 3) and the column selected in #2).
1) Select the type of bow you use – Compound column: A Recurve column: B 2) Select your arrow length in row C Correct arrow length is from nock groove to end of shaft.
c) Finger Release – move your correct spined shaft box 1 row down.
C H A R T S TA N D A R D S E T T I N G S This chart was established using a Hard Cam Compound bow with release aid, a Modern Recurve bow with finger release and Carbon Impact shafts with Insert and 110 grain point.
5) If the chart indicates you are between sizes, select the stiffer of the two sizes.
CORRECT SPINE SELECTION
A
b) Compound bows different than Hard Cam – For Soft Cam Bows move your peak draw weight box 1 row up. – For Round Wheel Bows move your peak draw weight box 2 rows up.
Gluing the point/insert – Apply a generous amount of 24-hour full-cure, flexible epoxy to the shank of the insert and to the inside of the shaft wall. Be sure the insert is fully seated and allow time for glue to fully cure before shooting. Hot melt not recommended. Warning: Do not use quick setting epoxy to install point insert. The bonding is not strong enough.
Warning: Never soak carbon shaft in harsh chemicals like acetone, paint thinner or MEK.
HOW TO USE THE CHART
a) Front weight different than standard setting – If lighter by 20 (40) grains move your correct peak draw weight box 1 (2) row up. If heavier by 20 grains move 1 row down.
Cutting the shaft – Always cut carbon shafts with nocks in place to ensure correct length. Only use a high-speed arrow saw with an abrasive wheel when cutting. Warning: Always use appropriate respiratory protection (NIOSH approved dust mask and safety glasses) when cutting arrow shafts.
3. Clean the surrounding area of the wound and inspect for the presence of carbon fragments.
3. Adjust and test your arrow rest – When setting up your bow check your rest settings, specifically, prong spacing, to insure your arrows will not fall through. Warning: An arrow jammed between the rest and the riser, or between the prongs of the rest could fail upon release and cause injury to yourself or others.
COMPOUND BOWS
Nocking the shaft – Firmly press the nock valley base until the Press Fit Nock is fully inserted into the shaft – for Rotonocks until the nock snaps into place. Doesn’t require glue.
2. Remove the flesh in the area of the wounds.
2. Recheck nock and point – Check point and nock ends to be sure they are securely attached and undamaged before each shot. Warning: Shooting damaged nocks or arrows can cause severe injury to the archer and / or spectators.
ADJUSTMENT T O T H E C H A RT
Impact – even if they look similar – could cause breakage or unseen damage to the shaft and could result in injury to the archer or spectators.
Arrow shafts could break after being shot into an animal, resulting in many sharp splinter-like fragments inside the animal. They can be harmful if ingested, therefore: 1. Use caution when field dressing game animals to avoid splinters of carbon fiber.
B
HOT: Hot Shaft XLT • ST: Stealth XLT • XLT: Fat Shaft XLT • TH: Trophy Hunter A R R O W
C
L E N G T H
F R O M
N O C K
G R O O V E
T O
E N D
O F
S H A F T
RECURVE BOWS
32"
Finger Release
55/65 6000 6000 400
HOT 55/65 ST 6000 XLT 6500 TH 350
42 TO 47
HOT ST XLT TH
55/65 6000 6000 400
HOT 65/75 ST 6000 XLT 6500 TH 350
55/65 6000 6000 400
HOT ST XLT TH
65/75 6000 6500 350
HOT 65/75 ST 6500 XLT 6500 TH 350
52 TO 57
HOT ST XLT TH
65/75 5000 6500 350
HOT ST XLT TH
65/75 6500 6500 350
HOT 65/75 ST 6500 XLT 6500 TH 350
57 TO 62
65/75 6000 6500 350
HOT ST XLT TH
65/75 6500 6500 350
HOT ST XLT TH
65/75 6500 6500 350
HOT 65/75 ST 6500 XLT 7500 TH 350
62 TO 67
65/75 6500 6500 350
HOT ST XLT TH
65/75 6500 6500 350
HOT ST XLT TH
65/75 6500 7500 350
HOT 65/75 ST 6500 XLT 7500 ————–
67 TO 73
Release Aid
26"
27"
28"
29"
30"
31"
47 TO 52
————– ST 5000 XLT 5000 ————–
————– ST 5000 XLT 5000 ————–
————– ST 5000 XLT 5000 TH 400
————– ST 5000 XLT 5000 TH 400
HOT ST XLT TH
55/65 5000 6000 400
HOT ST XLT TH
52 TO 57
————– ST 5000 XLT 5000 ————–
————– ST 5000 XLT 5000 TH 400
————– ST 5000 XLT 5000 TH 400
HOT ST XLT TH
55/65 5000 6000 400
HOT ST XLT TH
55/65 6000 6000 400
57 TO 62
————– ST 5000 XLT 5000 TH 400
————– ST 5000 XLT 5000 TH 400
HOT ST XLT TH
55/65 5000 6000 400
HOT ST XLT TH
55/65 6000 6000 400
HOT ST XLT TH
62 TO 67
————– ST 5000 XLT 5000 TH 400
HOT ST XLT TH
55/65 5000 6000 400
HOT ST XLT TH
55/65 6000 6000 400
HOT ST XLT TH
55/65 6000 6000 400
67 TO 73
HOT 55/65 ST 5000 XLT 6000 TH 400
HOT ST XLT TH
55/65 6000 6000 400
HOT ST XLT TH
55/65 6000 6000 400
HOT ST XLT TH
73 TO 79
HOT 55/65 ST 6000 XLT 6000 TH 400
HOT ST XLT TH
55/65 6000 6000 400
HOT ST XLT TH
65/75 6000 6500 350
HOT ST XLT TH
47 TO 52
For information on other Carbon Impact products not shown in this chart, please contact customer service at 231-929-8152.
®
9
FLUSH FITTING BREAK-OFF POINT
INTERNAL ROTO 10 NOCKING SYSTEM
UNMATCHED WEIGHT TO SPINE RATIO
ULTRA PERFORMANCE AND ULTRA PRECISION
Built for outdoor target archers, FITA, field…Ultra Fast are incredibly fast, responsive, and accurate! The lighter spines offer unmatched weight-to-spine ratios giving incredible performance for FITA style re c ur v e s ho o t e rs . T h e h e a v i e r
spines offer more weight for better downrange velocity and resistance to wind drift for compound shooters. ULTIMATE INTERNAL COMPONENTS
Flush fitting break-off points provide the ultimate in streamlined arrow flight. The push-on Roto10 pin nocks provide precise alignment for increased accuracy. (Nocks available in 2 sizes; large and small)
3 GRADES Straightness
Shaft Weight Variance
+ 1gr. - .003" Ultra High Quality For Top Target Archers
Green:
+
Orange: +- .004"
+
- 2 gr.
Excellent Quality For Tournament Shooters
Yellow: +- .006"
+
- 4 gr.
Best Value for all Target Archers
9 SPINES Spine Weight
1200: 950: 820: 710: 620: 550:
10
4.4 4.9 5.5 6.8 7.4 7.8
grain/ inch grain/ inch grain/ inch grain/ inch grain/ inch grain/ inch
500: 8.6 450: 8.9 400: 9.4
grain/ inch grain/ inch grain/ inch
For FITA and recurve target shooters
For compound field archers and 3-D shooters
A GREAT ARROW FOR MID-LEVEL SHOOTERS
5 SPINES FOR RECURVE AND COMPOUND
ALL INTERNAL COMPONENTS!
The new Super Club arrows offer the intermediate target archer a high tech full featured arrow – small diameter, internal components and amazing stiffness for the weight. Designed for recurve and compound bows, they offer accuracy, durability and speed.
Super Club arrows are available in 10/20, 15/25, 20/30 for recurve shooters (10 lbs. up to 35 lbs.) and 30/40, 40/50 for compound shooters (30 lbs. up to 55 lbs.). Proper spine and arrow weight can be achieved for every shooter down to the very lowest draw weight.
Flush fitting premium glue-in points, optimized for each spine, promote easy removal from target. Internal push-in nocks allow for easy nock clearance, perfect alignment and consistency.
INTERNAL PUSH-IN NOCK
SUPER STRONG CONSTRUCTION
FLUSH FITTING TARGET POINT
HOW TO USE THE CHART
C H A R T S TA N D A R D S E T T I N G S
1) Select the type of bow you use – Recurve column: A Compound column: B 2) Select your arrow length in row C Correct arrow length is from nock groove to end of shaft.
U LT R A F A S T & S U P E R C L U B S P I N E S E L E C T I O N
A
ADJUSTMENT T O T H E C H A RT a) Front weight different than standard setting – If lighter by 20 (40) grains move your correct peak draw weight box 1 (2) row up. If heavier by 20 grains move 1 row down. b) Compound bows different than Soft Cam – For Hard Cam Bows move your peak draw weight box 1 row down. For Round Wheel Bows move your peak draw weight box 1 row up. c) Finger Release – move your correct spined shaft box 1 row down.
This chart was established using a Modern Recurve Bow with finger release or a Soft Cam Bow with release aid and Ultra Fast arrows with 75 grain target point.
3) Select your draw weight in column A or B 4) Your correctly spined shaft is in the box at the intersection of the row selected in 3). and the column selected in 2).
B
UF: ULTRA FAST • SC: SUPER CLUB • FINGER RELEASE: 75-100 GRAIN TARGET POINT
RECURVE BOWS
C
A R R O W
L E N G T H
F R O M
N O C K
G R O O V E
T O
E N D
O F
S H A F T
SOFT CAM COMPOUND BOWS
23" 24"
25"
26"
27"
28"
29"
30"
31"
32"
23 TO 26
UF 1200 SC 1020
UF 1200 SC 1020
UF 1200 SC 1020
UF 950 SC 1525
UF 820 SC 1525
UF 820 SC 2030
UF 710 SC 2030
UF 710 SC 2030
UF 620 SC 3040
UF 550 SC 3040
34 TO 40
26 TO 29
UF 1200 SC 1020
UF 1200 SC 1020
UF 1200 SC 1020
UF 950 SC 1525
UF 820 SC 1525
UF 820 SC 2030
UF 710 SC 2030
UF 710 SC 3040
UF 620 SC 3040
UF 550 SC 3040
40 TO 43
29 TO 32
UF 1200 SC 1020
UF 1200 SC 1020
UF 950 SC 1525
UF 820 SC 1525
UF 820 SC 2030
UF 710 SC 2030
UF 710 SC 2030
UF 620 SC 3040
UF 550 SC 3040
UF 550 SC 3040
43 TO 46
32 TO 35
UF 1200 SC 1020
UF 1200 SC 1020
UF 950 SC 1525
UF 820 SC 1525
UF 820 SC 2030
UF 710 SC 2030
UF 710 SC 3040
UF 620 SC 3040
UF 550 SC 3040
UF 500 SC 4050
46 TO 49
35 TO 38
UF 1200 SC 1020
UF 950 SC 1020
UF 820 SC 1525
UF 710 SC 2030
UF 710 SC 2030
UF 620 SC 2030
UF 620 SC 3040
UF 550 SC 3040
UF 500 SC 4050
UF 450 SC 4050
49 TO 52
38 TO 41
UF 1200 SC 1020
UF 950 SC 1525
UF 820 SC 1525
UF 710 SC 2030
UF 710 SC 2030
UF 620 SC 3040
UF 620 SC 3040
UF 550 SC 4050
UF 500 SC 4050
UF 450 SC 4050
52 TO 55
41 TO 44
UF 950 SC 1020
UF 820 SC 1525
UF 710 SC 2030
UF 710 SC 2030
UF 620 SC 2030
UF 620 SC 3040
UF 550 SC 3040
UF 500 SC 4050
UF 450 SC 4050
UF 400 SC 4050
55 TO 58
44 TO 48
UF 820 SC 1525
UF 710 SC 2030
UF 710 SC 2030
UF 620 SC 2030
UF 620 SC 3040
UF 550 SC 3040
UF 500 SC 4050
UF 450 SC 4050
UF 400 SC 4050
UF 400 SC 4050
58 TO 61
11
• PATENTED GEL TECHNOLOGY • ULTRA HIGH EFFICIENCY • FOR ALL CAM TYPES
EXCLUSIVE CARBON FIBER TUBES
• WON’T FREEZE • WON’T LEAK
PATENTED GEL TECHNOLOGY
ULTRA LIMBSAVER DAMPENER
PAT E N T E D GEL SYSTEM This exclusive patented gel system is unique: The carbon tube is filled with a shock absorbing gel that has a mass suspended in it. When the bow vibrates, the mass counteracts, taming bow shock.
. .S U
nt te Pa
5 75 81 6 #6
.5 7
5
M AT C H Y O U R B OW
0 5.
z. o.
.5 7
5
"–
0 7.
"–
0 9.
z. o.
z. o.
O
P
TI
O N AL
Q
K LOC K
S
The Carbon Gel Ultra comes in 1" or 1-1/2" diameters, and 5" or 7-1/2" lengths, and a choice of the 3 most popular camo patterns, as well as classic carbon fiber black.
"–
0 4.
"–
z. o.
IC
12
Carbon fiber tubes channel energy away from the bow directly to the gel system, and to the “SIMS” Ultra LimbSaver dampener, destroying excess energy and vibration.
U
The Carbon Gel Ultra will not leak or freeze in varying temperatures.
EXCLUSIVE CARBON TUBES & U LT R A DAMPENERS
• D A M P E N S 3 W AY S • FOR ALL CAM TYPES
REVOLUTIONARY “CS” GEL TECHNOLOGY
• BALANCES THE BOW • WON’T FREEZE
6. 0
o. z. 5. 2
o. z.
The C10 Doinker dampener works with the front mass to counteract bow torque and recoil.
4. 3
The internal CS gel masses move freely inside the tube and counteract the vibrations received from the bow.
A carbon fiber tube makes up the lightweight body while the fiber bonding resin helps dampen shock. The Carbon CS Doinker stabilizers feature the all new C10 360° active vibration and noise dampener.
for field and target archery, and your choice of the 3 most popular camo patterns as well as classic carbon fiber black.
7 "–
This exclusive stabilizer is the best of two worlds: It combines some aspects of the now famous Gel Te c h n o l o g y w i t h t h e re n o w n Doinker dampener.
H I G H T E C H FAT CARBON TUBES AND DOINKER TECHNOLOGY
5" –
CARBON FAT CS DOINKER
11 "–
• WON’T LEAK
o. z.
EXCLUSIVE CARBON FIBER TUBES
MATCH YOUR BOW Carbon CS Doinker comes in three lengths; 5" and 7" for hunting and 11" "– 2
0 3.
z. o.
13
• TUNABLE DAMPENING EFFECT • INTEGRATED QUICKLOCK SYSTEM INTEGRATED QUICKLOCK SYSTEM
• SUPER HIGH EFFICIENCY • FOR ALL CAM TYPES
REINFORCED CARBON TUBES
• BALANCES THE BOW
TUNABLE FREE FLOATING SLIDING MASS
C A R B O N Q U AT R O L S CARBON
Q U AT R O D O I N K E R The Carbon Quatro Doinker stabilizer includes an integrated Quicklock, 4 dampening carbon tubes, a tunable free-floating sliding mass,
The new Quatro LS stabilizer is a new compact and economical version of the now well established Carbon Quatro stabilizer. Its length is 6.5" (5.3 o.z.) and comes in Hardwood HD camo / REINFORCED CARBON TUBES
black finish.
and the exclusive C10 Doinker System in the front. They come in two lengths; 8" (8.8 o.z.), and 11" (9.0 o.z.). Available in Hardwood HD camo / black for hunters, or
TUNABLE FREE FLOATING SLIDING MASS
in a classy silver / black for target shooters. ULTRA LIMBSAVER DAMPENER
14
PROCOMP A Stand-alone 32" or complete Sliding V-Bar System – both equipped with C10 Doinker System. QUATRO QUATRO B These 4-rod stabilizers come in 24", 31", 35" – equipped with Ultra LimbSaver dampeners.
HEXO C These 6-rod stabilizers come in 33" stand-alone, or complete Sliding V-Bar System – both equipped with C10 Doinker System.
Exclusive C10 Doinker System
A
Ultra LimbSaver Dampener
Silencing sliding weight for micro adjustment of stiffness and dampening properties.
Revolutionary 6 - Ro d He xo V- b a r Sy s t e m . (As seen in Athens FITA shoot).
B
Exclusive C10 Doinker System
QUICKLOCKS To attach / detach any target stabilizer with one simple twist. Will not vibrate loose. Will keep V-Bars leveled. Fits any stabilizer but Fat and Superfat.
C
15