T : To: Customer P/N: UDE P/N: BS-RB10072 Description: RJ45 1X1 Tab Down Through Hole 10 Base-T Contact Area : Gold Flash LED ith t LED LED:without
Spec No. BS-0072
Approved
Checked
Update Date 2010/8/2
Prepared
BS-RB10072
Spec No. : BS-0072
1. MECHANICAL DIMENSION 1.1 Product Dimension General Tolerance :
-1-
X X :±0 38 X.X 0.38 X.XX : ± 0.25
www.ude-corp.com
BS-RB10072
Spec No. : BS-0072
1.2 Recommened PCB Layout Component Side of Board p All dimension tolerance are ±0.05mm unless otherwise specified
-2-
www.ude-corp.com
BS-RB10072
Spec No. : BS-0072
1.3 Standard RJ45 Plug Specification
- All dimensions follow : FCC subpart F, 68,500, Figure (C)(2)(i) & (C)(2)(ii) & (C)(3)(i) IEC 60603-7 - All plugs must be meeting the requirements of plug Go & No-Go No Go gauge. Gauge follow : FCC subpart F, 68,500, Figure (C)(4)(i) & (C)(5)(i) - There must be no damage to Housing and Locking Latch. - There must be no nicks and cuts in cable. - Durability : 750 cycles generally -3-
www.ude-corp.com
BS-RB10072
Spec No. : BS-0072
2. REQUIREMENTS 2.1 Design g and Construction Product shall be of design, construction and physical dimensions specified on applicable. 2.2 Material 2.2.1 Terminal Parts (Underplating : 30μ" min. Nickel overall) 2.2.1.1 RJ Terminal : PH. Bronze, Thickness=0.30mm Finish : Contact Area : Gold Flash 2.2.1.2 Input Terminal : Brass, Thickness=0.35mm Finish : 100μ" min. Tin 2.2.1.3 Case Terminal : Brass, Thickness=0.30mm Finish : 100μ" min. Tin 2.2.2 Plastic Parts 2.2.2.1 Housing : High Temperature Thermoplastic, Black 2.2.2.2 Case : High Temperature Thermoplastic, Black 2.2.3 Shield Parts : Stainless, Thickness=0.20mm, Pre-soldering
-4-
www.ude-corp.com
BS-RB10072
Spec No. : BS-0072
2.3 Operating and Storage Temperature Operating : 0°C to +70°C p g Temperature p Storage Temperature : -40°C to +85°C 2.4 RJ45 specifications Insulation Resistance 500MΩ min. Insertion force with the latch depressed 22N max Removal force with the latch depressed 44N max Locking Force of Plug Latch : 50N min. @ 60+/-5 sec Durability : 750 cycles 2.5 Performance and Test Description Product is designed to meet electrical, mechanical and environmental performance requirements specified in below table. All tests are performed at ambient environmental conditions per MIL-STD-1344A and EIA-364 unless otherwise specified. 2.6 Packaging and Packing All parts shall be packaged and packed to protect against physical damage、corrosion and deterioration during shipment and storage.
-5-
www.ude-corp.com
BS-RB10072
Spec No. : BS-0072
3. ELECTRICAL CHARACTERISTICS 3.1 Schematic
INPUT RJ45 OUTPUT TCT R3 1:1 TD+ R1
C1 TX+
TD‐ R2
C2 TX‐ 1:1 1 1
RD+ R4
C3 RX+ C6 RX‐
RD‐ R5 R7 R8
GND
-6-
www.ude-corp.com
BS-RB10072
Spec No. : BS-0072
3.2 Transmitter filter Type yp : Balance low pass p 100Ω impedance p Cut off frequency : 17±1.5MHz –3.0dB TYP Insertion loss :
Return loss :
1~10 MHz
-1.0dB max.
@30 MHz
-28dB min.
@40 MHz
-33dB min.
1~10 MHz
-13dB min.
load 100Ω
3.3 Receiver filter Type : Balance low pass 100Ω impedance Cut off frequency : 17±1.5MHz –3.0dB TYP Insertion loss :
Aug 2, 2010 - 2. REQUIREMENTS. 2.1 Design and Construction g. 2.2 Material. Product shall be of design, construction and physical dimensions specified.
... of our products at any time as part of the company's continuous improvement .... power-up the fixture in order to allow the 0-10V dimming to function properly.
Vérifiez l'absence de conducteurs exposés, de fils lâches ou d'éléments d'isolation coincés. 6. Mettez sous tension. Protection de l'environnement (D.E.E.E.) ...
... vor dem Umbau. Michel Roduit: Mit der Solartechnik hatten ... Zu Besuch bei Josyane und Michel Roduit, ...... Marc Muller, Bereichsleiter Sonnenenergie, BFE.
South Africa. Tel: +27 .... altération et du retrait de l'étiquette de contrôle de qualité, d'une installation dans un environnement mal approprié ou d'une installation ...
Turn power OFF to the fixture. 2. Remove existing T8 4FT fluorescent lamp from the fixture. 3. Inspect the sockets and wiring to ensure they are in proper working ...
While holding reflector cone or baffle in place, align three ... CONSTRUCTION recessed cans, please use the .... wise to release trim ring and reflector cone or.
... should be replaced. • Recycle: For information on how to recycle LED electronic products, ... ▻Keep combustible and other materials that can burn, away from lamp/ lens. ▻Do not ..... Le réfracteur/la lentille doit être lavé(e) dans une solution .
Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov. • These instructions do not purport to cover all details or ...
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION. LEAVE A ... Isolate the mains supply before servicing or installation. FOR DALI ... 2. Connect the mains supply to the LED Driver supplied with the panel as per figure below: 220-240V. Sup
1 janv. 2009 - To stop the search before it has finished, press the ENTERE button with Stop selected. ..... selecting Tools â Switch to Cable (or Switch to Air).
1 janv. 2009 - Samsung Electronique Canada Inc., Service ...... bordures à gauche, à droite et au centre de l'écran, à cause de la différence d'émission de lumière sur ...... À brancher aux prises d'entrée audio de votre amplificateur/chaîne ...
Website: www.auroralighting.com ... of the National Wiring Regulations and taking into consideration the latest Building ... Should this product fail during the warranty period it will be replaced free of charge, this is subject to correct installati
Once all connections are complete, gently push the LED trim into ... LED module, plug connector from the module into the mating connector just installed into the.
iThis luminaire is not suitable for covering with insulation material. INSTALLATION INSTRUCTIONS. 1. Before commencing installation or maintenance ensure ...
... de procéder à tout changement sans notification préalable www.sonia-sa.com espec_461. Imagenes no a escala / Draw not to scale / Echelle non respectée.
Les étiquettes ou marquages existants doivent être retirés et un nouvel étiquetage doit être ajouté au luminaire. •. Lors de l'installation ou du remplacement des ...
Before commencing installation or maintenance, ensure electricity is ... Attach the earth lead to the circuit earth conductor using an approved terminal block. 5.