VAR: name of the variable which will be tested. VALUE: value to compare the variable with. OPER: one of the allowed operands. LESS: true if the variable is less ...
Library : tlUtils.dll Attributes : None. Content : Any command. Role : Body of the scenario (launcher, responder, traffic agent), encloses all the other commands. SEQ anchor should start every test sheet. Example : Hello World Result: Hello World
2.
EXEC
Library : tlUtils.dll Attributes : FILE : filename of the test sheet (plain text, usually ends with .xml), in global or relative format (if no directory, will assume the test sheet is located together with the caller test sheet. Content : None. Role : Execute a test sheet within the current execution scope (global variables). If the test sheet was compiled together with the tulip.xml file, it will also use the same constants. Example : 4
Result: File ABODR.XML will be executed as if the commands were part of the caller test sheet. In case the file des not exists, there is a non blocking error message.
5
3.
SPAWN_AGENT
Library : tlUtils.dll Attributes : SELECTOR: name of the test agent parameter used as the selection criteria. VALUE: value of the selector used. Content : Any command. Role : Starts concurrents thread to the current one, each dedicated to a traffic agent. The attributes provide a flexible way to select which traffic agent to start. The agents will execute in loop,depending on SCHEDULER parameters in tulip.xml. The fields selected are the agent attributes as defined in tulip.xml file. From that time, all agent attributes can be accessed as normal variables. Example : URI of caller traffic agent is ~URI~ Result: URI of caller traffic agent is test1 URI of caller traffic agent is test2 URI of caller traffic agent is test3
6
4.
STATE
Library : tlUtils.dll Attributes : NUM: index of the current state. Content : None. Role : Works as a label for the current agent status. This is used for test result analysis, as it is kept in log each time an error occurs. The state label is global to the agent in execution, each time it is set it will not change until set again or if the agent loops back. By default it is equal to 0. The STATE is an agent attribute, it can be obtained anytime like any variable Example :
This manual describes the AT commands for PCTEL modems. AT Command Format .... N1. Enable auto-mode. The modem will connect at the highest available line speed and ignore any ... Result codes will be sent in numeric form. (See the ... 7. AT Command G
ATDmn will dial a phone number where m is a modifier: L, W, ,, ;, @, !, or S. It will dial the telephone ...... . Microphone Gain Parameter. 0. 0 dB. 1. 6 dB gain (default). 2. 9.5 dB gain. 3 .... This command sets the audio codec-sampling rate.Missi
Pierre Paulin RDI / Design 1965 - Reintroduction 2003. Little Tulip. Little Tulip. Elegantie ten top. Sierlijk ... Altijd even charmant. Prachtig aan een eettafel,.
About This Manual. This reference guide provides descriptions of the AT commands that are ...... Table 1â17 lists the pos- ... proper training sequence in the selected mode, followed by a constant series ..... Reserved for future standardization.
2 Depending on the source of your command-line program files, do one of the ... 1 Open a standard MS-DOS or Windows text editor, then type the following ... Removing the software leaves your computer unprotected against virus attack. .... Response an
Numéro de Socket Pour jouer sur un réseau local IPX (voir Partie Multijoueurs). Ne pas demander ensuite (Don't ask again): Permet de ne plus activer l'écran.
May 18, 2006 - Command List. An application example ..... This command will display a list of the available general commands. The list .... 0 Invalid Fix. 1 2D fix.
statements provided in this manual should not be interpreted as such. .... db2logsforrfwd - List Logs Required for ... Command Line Processor Return Codes .
01215 (Oeuf rouge-gorge). 1 balle. Une paire d'aig 4.5 mm (U.S. 7) ou la grosseur requise pour obtenir la tension. TENSION. 20 m et 26 r = 4 po [10 cm] en point ...
Figure 1-2 shows a block diagram of the RN52 with Bluetooth audio and .... After pairing with the device is successful, the module can now connect to the device.
As Commander of an elite division of XT-87 attack vehicles, you must penetrate their defenses, and triumph despite the enemy's valiant, suicidal last stand.
features Hive Fleet Kraken and its many tendrils as they invade the Ultima Segmentum of Imperial space during. 992.M41 and later. However, even though this ...
Jan 9, 2007 - Chapter 17. âEViews Programming,â on page 593 describes the basics of using pro- ...... Specifies whether and how to draw the individual coeffi- ...... computes scores in the same fashion, but only saves factors 1 and 2. ...... PDF
Configuring a RADIUS Server to Download Per-User Access Control List Names 20-14 ...... This guide includes the chapters and appendixes described in Table 1. ..... periodic checks to perform on remote Microsoft Windows computers. Cisco.
Nov 28, 2005 - The studio that published the content. Cast/Creators ..... Poland. PT. Portugal. PR. Puerto Rico. QA. Qatar. RE. Reunion. RO. Romania. RU.
Applications. • Secteur de l'hébergement. • Secteur de la santé. • Secteur de l'éducation. • Gouvernement. • Magasins de détail. • Enceintes de biosécurité (ESB).
Aug 12, 2014 - Each instruction set contains four types of AT commands. Type. Instruction Format. Description. Test. AT+=? Query the Set command or ...