in a safe direction and fire several times to be sure there are no balls left ... Pneumatics Service ... 260/749-6022 ⢠800/533-4831 ⢠FAX: 260/749-6619 ⢠3518 Adams Center Road ⢠Fort Wayne, IN 46806 ⢠INTERNET: www.tippmann.com ... A-5 Flatline Barrel System Schematic. Cap screw to the left. Front. Sight. Cap. Screw.
A-5 FLATLINE BARREL SYSTEM INSTALLATION INSTRUCTIONS
TIPPMANN
For Free Installation contact Tippmann Pneumatics Service Department at 260-749-6022
PNEUMATICS, INC.
WARNING: DO NOT field strip or otherwise disassemble this gun while it is pressurized with gas. Disassembling the receiver while under gas pressure will cause personal injury & / or damage to the gun. Remove CO 2 cylinder or CO 2 cartridge before doing any disassembly.
INSTALLING THE A-5 FLATLINE BARREL SYSTEM READ EACH STEP COMPLETELY BEFORE PERFORMING STEP
WARNING: DO NOT OPERATE THIS MARKER WITH PARTS MISSING OR DAMAGED. If during the course of this installation, a part is lost or found to be damaged, obtain a replacement part before continuing reassembly. The Flatline Barrel System Kit Contains: 1-Flatline Barrel System; 1- Flatline Barrel Plug; 1- Flatline Barrel Squeegie Set up a table with plenty of space to work. Tools You Will Need: 1/8" allen wrench & 3/16” allen wrench. (Both allen wrenches were included in your A-5 accessory pack)
Step 1: Prepare Marker for Flatline Kit Installation To do so, you must: (1- unload your marker; (2- remove CO2 source; and (3- uncock marker before further disassembly. 1) Unload your marker: first remove the hopper. Then, point your marker in a safe direction and fire several times to be sure there are no balls left in the feeder or lodged in the chamber. 2) Remove tank: To remove a charged CO2 cylinder, turn the cylinder approximately 3/4 of a turn counterclockwise or out. This allows the tank pin valve to close so that no CO2 will enter the marker. Point the marker in a safe direction and fire the remaining CO2 in the marker by pulling the trigger until the marker stops firing. (This may take 4-5 shots) If your marker keeps firing after you have turned the tank 3/4 of a turn, the tank pin valve has not closed yet and you may have to turn the tank counterclockwise a little further. If you turn the tank 3/4 of a turn and it begins to leak before you pull the trigger you have turned it too far and may have damaged the tank o-ring. 3) Put the marker in the uncocked position: hold the bolt cocking handle back - then pull the trigger and release handle forward to un-cock the marker.
Step 2: Remove A-5 Stock Barrel & Barrel Adapter 1) To remove stock barrel & barrel adapter as one unit, turn barrel to the right to tighten it into stock adapter.
Receiver Reference
Front Sight
Stock Barrel
A
Feeder Housing
Upper Receiver
Step 3:
Step 4:
Position Barrel Adapter cap screw facing the left toward feeder housing and insert into receiver.
Turn Barrel Assembly 1/4 turn to the right until the adapter cap screw aligns with the front sight. Front Sight
Feeder Housing
Cap Screw
Cap screw to the left
Step5: While keeping screw and front sight aligned, tighten the 3 receiver screws A, B & C to complete the installation. Barrel at top
Proper screw position
Proper screw position
Properly installed barrel will look like this.
A
B C
A-5 Flatline Barrel System Schematic It is not necessary to disassemble the Barrel System to install it. If it is ever taken apart, be sure barrel and adapter alignment marks are aligned when reassembling. Cap screw
Barrel Adapter
Adapter Set Screw
Barrel Shroud Shroud Cap
B C
2) Loosen 3 receiver bolts (A, B & C) then turn barrel/adapter to left and remove as one piece from upper receiver. Store removed barrel / barrel adapter, old squeegie and old barrel plug in a safe place. (WARNING: Do not use old barrel plug in Flatline barrel. Old barrel plug is not designed for use with Flatline barrel and may shoot out causing injury.)
Alignment Barrel Marks Adapter
Cap Screw Barrel
Note: Eye protection designed for paintball use must be worn at all times when handling this marker by the user and any person within range.
260/749-6022 • 800/533-4831 • FAX: 260/749-6619 • 3518 Adams Center Road • Fort Wayne, IN 46806 • INTERNET: www.tippmann.com
to give an.over-running effect after the engine starts to prevent the engine from driving ... starting. Not until the engine is running will the gear release. (approx.
La petite vie de Ci 2017 - Personal use only. OCTOBER. S M T. T F S. W. 1. 3 4 5. 2. 6 7. 8. 15 16. 9. 17 18 19 20 21. 24 25 26 27 28. 10 11 12 13 14. 22 23.
Jul 17, 2006 - artefacts well above the audio band. They are then .... number of tracks available on the CD, and total playing time. .... book CDDA standard.
cycling when riding in public traffic. Please be remin- ded that your child needs some time to get used to his/her new bike. In addition children are allowed to.
Utilisation en usine alimentaire : Ãviter la contamination des aliments durant l'utilisation ou l'entreposage. La batterie ou les ustensiles de cuisine et les autres.
Durée de conservation 1 an. Solubilité dans l'eau. Complète. Densité. 1,011. Rappel des consignes de sécurité. Veuillez vous assurer que vos employés lisent ...
Gluck : 3 airs extraits de Orphée et Euridice. Mozart : 2 airs tirés des Noces de Figaro, 1 air de Cosi fan tutte. Berlioz : air tiré de Béatrice et Bénédicte. Delibes ...
Ne remonter jamais la tige de selle et la potence au delà de la marque. Dans quel cas, la connection pourrait lâcher et causer une grave chute. Contrôlez que ...
En regardant de l'arrière de la carabine, retirez les deux 10 mm vis cruciformes qui maintiennent le bouchon orange pour la crosse du fusil.. Retirez le ...
parent test of pelagic animals, open at both ends and shaped by the amphipod. ..... Since no attempt to test cluster separation is intended, these deviations from.