SPORTPLANE BUILDER
Tony Bingelis
PAINTING YOUR HOMEBUILT (Lessons Learned and Relearned) Part 2
Here's why surface preparation is so important.. . Paint will only color the surface to which it is applied. It will not hide: 1. Rivet heads - especially the pop rivet variety 2. The slightest scratch or scuff mark 3. The smallest dent 4. The tiniest of pin holes in a fiberglass component 5. A bump, or any kind of surface roughness I must admit, however, with some chagrin, that I apparently have trouble convincing myself this is truly so. It is only when I carefully examine a freshly painted surface and find small areas where my preparation work wasn't all it should have been that the lesson sinks in. My most persistent fault is in not taking the time to sand away the faint sandpaper marks left by coarser grades of sandpaper. Don't be guilty of making the same mistake. Discipline yourself to sand away all signs of surface roughness and scratches with progressively finer sandpaper. Finish your surface preparation using #350 grit wet/dry sandpaper . . . #400 grit is even better. Neither grade will leave visible sanding marks. Incidentally, using the fine grit sandpaper with water allows it to cut better and keeps the sandpaper from clogging. I say, again, if you want a good paint job, you must remove all the dents, scratches, pin holes, and other imperfections before you pick up the spray gun and shoot the first coat. Unfortunately, pre-paint preparations, up through the primer coat, are quite demanding and entail a lot of hard work. You will find, for example, it takes up to 50 times longer to prepare the surfaces than it does to spray on a color coat. Although each type of aircraft construction may require preparation methods that differ somewhat, they 68 JANUARY 1995
Finish your surface preparations using #350 grit wet/dry sandpaper. #400 grit is even better. However, neither grade will leave telltale (visible) sanding marks which could otherwise show up under the final color coat.
The best masking job results when you use regular heavy duty masking paper not newspapers or plastic sheets.
all have this in common. Each type of construction - be it metal, composite, wood or tube and fabric - requires many more hours to be spent in surface preparation than in painting. Many builders do not realize that the prefabricated polyester fiberglassed components they receive will continue to shrink for months after
manufacture. Consequently, you can generally detect the weave pattern of the glass cloth through the gel coat. This pattern will also show through the finish color coat, especially on your cowling, although it won't be as obvious to the casual observer. If this bothers you, minimize or
eliminate the textured appearance by
giving your fiberglass parts, particularly the wing tips and cowling, a couple of fill coats of a good sandable primer. Sand between each coat using a medium hard rubber sanding block to back up your #350 or #400
wet/dry sandpaper. Incidentally, sanding with straight line strokes is not the best way to do it. You will obtain much faster and more uniform results if you sand in a circular motion. After you have completed all sanding preparations, blow off the sanding dust with an air hose. Poke the nozzle
into all the corners. If you don't, any
Using targe sheets of plastic to supplement the areas properly covered with masking paper is O.K. but be absolutely sure the loose ends of the plastic sheets are taped down to prevent breezes from blowing an unsecured corner up into a freshly painted surface.
entrapped dust will be raised by the spray gun air blast, and some of it will settle in your finish. Finally, examine every square inch
of the newly prepared surfaces. Pay close attention to all the edges. These should be sanded or filed smooth and slightly chamfered. It is along these edges where there may be some overlooked felt pen markings. All marks you find must be completely removed using plenty of thinner. An overlooked ink mark notation, or ink line, will surely bleed through your nice finish and will cause considerable regret later. What To Do About Pesky Pin Holes
Only fiberglass parts are capable of
producing such an obnoxious blight in a finished surface. Pin holes show up
Your Plexiglas™ canopy can't stand much abuse. Keep it and the windshield completely masked . . . both inside and out, while any kind of painting is underway anywhere near i t . . . no matter how small and quick you think the job will be.
Here the wheel pants and spinner are suspended on posts so they can be spray painted completely on all sides . . . at one time.
most in fiberglass layups, and especially in factory made components when some of the gel coat has to be sanded to the bare fiberglass surface. Spraying primer, or paint, over pin holes is futile because the paint merely straddles the tiny holes and the pin holes become even more visible in the final finish. The cure for eliminating pin holes is to fill them by using 3M Spot Putty, or a similar automotive filler (personally, I like "Marine Tex"). You can also brush a sandable primer over the holes and rub the stuff in with your fingers until they disappear (I mean the holes). After the pin hole filler has dried, sand the area smooth. You may find that a second treatment is often necessary after you inspect the sanded results. Unfortunately, pin holes are not easily spotted until the surface has been primed. Even so, you might miss quite a few pin holes that will, to your disgust, show up in the finish coat. SPORT AVIATION 69
cellent for trim striping, and for use against Plexiglas™ windshields and canopies is the 3/4" wide black electrical tape. It is quite inexpensive and, being very thin, can be easily stretched around sharp curves. It, too, leaves nice clean trim lines after the tape is removed.
As soon as you have completed spraying a component - whenever possible try to turn the part to a horizontal attitude to lessen the risk of paint runs.
What can you do when more pin
holes show up in the finish coat?
That's right, you'll have to live with them unless you have the resolve to re-treat and refinish the part. The Art of Masking
If you want a quality paint job you must be willing to use quality products. I believe the tapes best suited
for masking color line separations is 3M's "Fine Line Tape" or a good grade of Mylar filament tape. They produce masked lines so sharp that trim colors rarely bleed under their edges. The tough fine line tape with its polypropylene film backing cannot be torn by hand. It has to be cut with a razor or scissors. The 1/2" width is the most practical to use. Another tape that I find to be ex-
On the other hand, the ordinary 3/4" wide (crepe) masking tape most of us buy because it is inexpensive is not as effective to use for striping because paint will sometimes bleed under its edges and leave a fuzzy looking trim line after it has been removed. As a rule, I never use the ordinary crepe masking tape against a finished surface. Instead, I use that kind of tape primarily for attaching the masking paper to and along the fine line
tape color separation striping.
Both the fine line tapes and the electrical tapes are easy to remove. I can't say as much for the crepe mask-
ing tape which is often difficult to peel off if left on too long. If you have to touch up or refinish
your instrument panel, here is the easiest way to mask it when the instruments are already installed: 1. Cover the glass face of each instrument completely with strips of ordinary masking tape. You can do the job quicker if you use masking tape at least one inch wide. 2. Run your fingernail around the perimeter of the glass face to seat the
edge of the masking tape tightly.
3. Next, using a single edge razor
blade, run its cutting edge around the instrument glass. 4. Peel away the excess masking tape leaving the instrument face completely masked and the panel is ready for painting.
Obviously, it would be much easier to paint the instrument panel
before installing the instruments as
no masking would be necessary. However, during the installation of the instruments and other cockpit work, the day may come when you need to refinish the panel without all the work involved in removing the instruments. No matter how careful I try to be in masking the various components, I
sometimes find a spot or two where
the paint has bled past the masking paper and tape. The blemish is usually a small spot or a triangle of fresh paint that somehow leaked onto the
The critique of your paint job is inevitable as fellow builders are not bashful about selflessly volunteering their comments. 70 JANUARY 1995
primary finish I intended to protect. Unfortunately, the discovery is made only after the masking paper and tape
has been removed. The best way to prevent that sort of thing is to carefully examine every single inch of the masked edges to assure yourself that the masking paper covers everything and that the tape is down tight. Assure yourself, too, that
all overlapping edges are taped tightly. Cut the tape with a razor if necessary to make the tape behave. Your Plexiglas™ canopy can't stand much abuse. Keep it and the windshield completely masked, both inside and out, while any kind of painting job, no matter how small, is being done anywhere near it. This will protect the Plexiglas™ from accidental overspray . . . and save you from a lot of cleaning and polishing later. As you may have noticed, I use a variety of "masking" tapes. 1. The most important is the 1/2"
3M Fine Line Tape. This is the tape
professional painters use to outline
the color separations or trim design. It is affixed directly onto the surface you want to mask. Cheap masking tape is O.K. to use but it must never be used in direct contact with a finished surface. Instead, use it to attach masking paper
Cleaning up after a paint job is not as simple a task as you might have believed, protecting your work surface and hands before you start painting would be a wise move. to the fine line tape already in place.
3. A third tape I use often is ordinary black electrical tape. It is the only kind of tape I ever use to mask off windshields and canopies. Because its edges are extremely thin and smooth, laying out clean cut
6
Just one loo
curved lines are possible when you use it. It is easy to apply and just as easy to remove without leaving an objectionable residue. Unlike ordinary masking tape it may be left on for a fairly long time (a week or two) without becoming difficult to remove.
VM1OOO Engine Instrumentation Caution Advisory System
"The most advanced engine management system on the market."
> Full Sweep Graphics Fast visual reference lo operating limits and trends
>• 'Autotrack'™ Mode Automatically tracks changes in engine performance during flight
> 'Diamond Graph'™ EGT / CHT Fuji-feature engine analyz-
er plifc digital readout
* Advanced Technology Microprocessor control plus flat panel
high-contrast display
* High Reliability Precision components, craftsmanship and quality control testing
..is all you need. SPORT AVIATION 71
The deed is done and off to the airport it goes ... congratulations!
Masking Paper
The best masking job results when
you use regular heavy duty masking paper, not old newspapers or plastic sheets. Be sure the masking paper you use will not allow the paint to bleed through it. If it does, you will have one big problem, amigo. I don't recommend using large plastic sheets as a substitute for masking paper. You may overlook covering
all the areas you want protected because the plastic is transparent and you may not notice places left unprotected by the plastic. A roll of 14" wide masking paper is not too costly when you consider it may save you from a botched up paint job. Using large sheets of plastic to supplement the areas properly covered with masking paper is O.K. but be absolutely sure the loose end of the large plastic sheets are taped down to prevent breezes from blowing an unsecured corner up into your freshly painted surface. It happened to me once. Consider yourself warned, so don't blame me if it should happen to you, too. Before you paint, go over every inch of the masked line, running the back of your finger nail along the edge to be sure it is down tight against the surface to be painted. 72 JANUARY 1995
Masking paper can be removed in an hour or so after painting. Do it carefully and be sure you don't allow some of the masking paper, or the loosened tape, to accidentally contact the fresh paint. I like to remove the masking tape and paper before the paint dries hard overnight. That kind of delay in removing the masking tape may result in a fuzzy brittle edge between the two colors. Painting Traps Can Be Avoided Failure to read and follow the paint manufacturer's instructions often causes the most grief for the new builder. Follow the manufacturer's mixing recommendations by carefully measuring out the correct amounts of color, reducer, and hardener as instructed.
The most common finishing flaw,
other than runs, is the orange peel appearance of an otherwise nice smooth shiny finish. It is usually an indication that the paint should have had more reducer (thinner) added to allow it to flow out better. The risk, however, is that thinning paint too much (especially in cooler weather) will increase the risk of producing runs. Of course, when temperatures are high, more thinning should be anticipated.
Your last act before pulling the trigger on the spray gun is normally a quick wipe of the surface to be painted
with a tack rag. A tack rag is a very inexpensive, sticky-feeling type of rag especially
treated for a very special purpose . . . to pick up dust.
It is the one sure way to wipe off those last minute dust particles that
may have gathered on your surfaces.
Painting vertical surfaces requires the greatest care as making one pass too many with the spray gun will result in runs or sags . . . especially in corners and at lapped joints, or where
you inadvertently let the spray gun
get too close to the surface. And yet, if you don't give the surface at least three good passes you may not get the flow-out and gloss you want.
At any rate, as soon as you have completed spraying a component, whenever possible try to turn the part you have just painted to a horizontal attitude to lessen the risk of paint runs. I hate to say it again but paint runs are prone to occur when the paint is
thinned or reduced too much. And yet, if it isn't thinned enough you may get that "orange peel" appearance in the finish. Don't be in too great a h u r r y to wipe away a small paint sag or run. It might level itself and become inoffen-
sive after the paint cures . . . especially if the surface can be turned
level immediately after it has been painted. Inspect the Finish For Flaws
6. Felt pen or "Sharpie" ink marks
that you overlooked removing completely.
You didn't find any? Congratulations!
Source Information
Marine Tex is an excellent two part spot filler that will not shrink. Most marine and boat sales outlets carry it.
After you have finished painting,
inspect your work closely. Hopefully, you won't find any, but here are some flaws to look for: 1. Small areas that didn't get painted, or didn't get enough paint. 2. Places where the paint leaked past the masking paper or masking tape . . . usually where there is a gap between parts or where there is a lap joint. 3. A place where you may have, ina d v e r t e n t l y , brushed against the freshly painted surface with the spray gun, the hose, or your sleeve. 4. Spots or small areas where the paint just seemed to separate and refused to cover. Most likely that particular area was contaminated by oily fingerprints, or wasn't properly cleaned and "degreased." 5. Any localized runs, curtains and sags that you didn't notice before. These occur most frequently in corners, joint laps and on edges.
BOOKS BY TONY The following books by Tony
Bingelis are available from the EAA Aviation Foundation, EAA Aviation Center, Box 3086, Oshkosh, WI 54903-3086, 1-800/843-3612. Major credit cards accepted.
If you wish to contact the author of this column for additional information, please send a SASE to: Tony Bingelis 8509 Greenflint Ln. Austin, TX 78759
KITFOX VOTED #1
At Oshkosh '94 SkyStar was voted the Manufacturer of the Year by LAMA, a peer group of manufacturers and EAA Chapters nationwide. The award described SkyStar as: "bringing business
Kitfox Serie5 5 Vixen
If you're looking for a fast and
fun to build, fun to fly, folding wing, STOL performance aircraft, act now and request
more information on the best selling KITFOX.
Kitfox Classic IV on optional floats
integrity, innovation, and high quality to the amateur-built aircraft community" and as "a creative manufacturer who provides What can truly be said to be the light aircraft of grass roots aviation." We appreciate the confidence and recognition of our peers and customers in the industry. Over the past 10 years, our company has helped over 2,400 pilots around the world become successful homebuilders with the versatile and fun loving Kitfox.
Choose from three high performance designs and a wide variety of options. •h
Kitfox Series 5 Talldragger
-Sportplane Builders (Aircraft Construction Methods, 320 pages) - $19.95 -Firewall Forward (Engine Installation Methods, 304 pages) $19.95. -Sportplane Construction Techniques (A Builder's Handbook,
350 pages) - $20.95.
Add $2.40 postage and handling for each publication ordered... or order all three for $52.97 plus $6.95 postage and handling. Wisconsin residents add 5% sales tax.
Informative literature is available in English, French, German, Italian, or Spanish. • Full Color Info Pack-$15 • Award winning 30 min. VHSVideo(NTSCorPAL)-$15 • Both Info Pack and Video - $25 • Add $5 overseas. :, ;J To request additional information, an Info Pack or Video, call our
New 24-Hour Hotline.
VISA and Mastercard Accepted.
1^800-5-KITFOX
Dream It, Build It, Fly It! To speak with a Factory Representative call our office near you:
CORPORATION
100-A N. Kings Rd. Nampa ID 83687
Tel: 208-466-1711 Fax: 208-466-8703
A-La Verrerie Basse F-81140 Vaour France
Tel: (33) 63.56.31.81 Fax: (33) 63.56.31.50
SPORT AVIATION 73
