Sony Reader Touch Edition PRS-600 Plastic Casing Covering the Screen Replacement
Sony Reader Touch Edition PRS-600 Plastic Casing Covering the Screen Replacement This guide will show how to replace the plastic casing that covers the screen.
Sony Reader Touch Edition PRS-600 Plastic Casing Covering the Screen Replacement
Étape 11
Pull the panel away from the device. You may have to use the flat end of the spudger to remove the side portion of the panel because it will be glued in place.
Using a Phillips head screwdriver, remove the one 1.4 mm screw holding in the motherboard.
Page 8 de 14
Sony Reader Touch Edition PRS-600 Plastic Casing Covering the Screen Replacement
Étape 13
Using the flat end of the spudger, flip up the 4 latches holding down the thin, orange strips that connect the motherboard to the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports.
To disconnect the the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports pull each orange slip away from their corresponding latch.
Étape 14
Lift the end of the motherboard closest to the memory cards and pull out.
Using the Phillips head screwdriver, remove the two 1.4 mm screws in the screen at the bottom of the device that are usually covered by the power switch panel.
Page 10 de 14
Sony Reader Touch Edition PRS-600 Plastic Casing Covering the Screen Replacement
Étape 17
Using the same screwdriver, remove the 1.4 mm screw at the bottom of the device that is usually covered by the bottom and side panel.
Remove the four 1.4 mm screws that are located on the side of the device that are usually covered by the bottom and side panel.
bottom right corner of the device.. Using the pointed end of the spudger, push out the white plug that is connected to the battery from its beige base.
Products with electronic ballasts must not be installed on the same electrical circuits as products with inductive loads, for example ... BARE, OR GREEN.
was discovered in 1997, and is essentially a big floating soup of plastic garbage and bits of rubbish ... entire week, which is fantastic. Kate: Oh that sounds great, ...
welding metal. If it's at all reassuring to those of you who don't weld metal because .... surface-bonding strength; is ready to sand in about 15 minutes; and has a ...
Holding the part up to the light should reveal any hidden crack damage. Subsurface stress cracks look like lighter-colored lines or patches of lines and should be ...
Mar 1, 2009 - The CREATE USB Interface (or CUI board) is made and produced by Dan Overholt (AAU, DK). It is IMO a good alternative to the more famous ...
Designing with composites opens door to new shapes and performance those. By Neal ... The students of Akaflieg. Stuttgart built the first all-compos- ite sailplane, the FS-24 Phönix, in. 1957. .... Page 5 .... single ply is also about 9 ounces per .
ash catcher and could ignite, resulting in a fire below the bowl. Remove any starting fluid from the ash catcher before lighting charcoal. A - Asche entfernen B ...
Couper les pièces de tissu suivantes pour votre sac: une pièce de 18" x 20" (45.72 x 50.8 cm); une pièce de 13" x 20" (33.02 x 50.8 cm); deux pièces de 2" x 20" ...
Please write your model # on your sales receipt or below. Le n˚ de modèle est indiqué près du code-barre. inscrire le n de modèle sur la facture d'achat, ou ci- ...
In metal ships, too, virtually all cables, engine grounds, shield wires, and ignition grounds are bonded to the conductive airframe. As opposed to plastic airplanes ...
4 mars 2014 - If multiple cards are waved simultaneously, proper reading will not be ... System integrators must include the FCC ID on the end product.
Use a zigzag or overlock stitch to finish the raw edges. 3. ... Use a safety pin to thread the ties through the casing at each end of the bag. 9. ... ouverte et à plat.