Electric cables and mains plug should be inspected for damage and replaced ... In addition, electrical safety checks for earth continuity (class I equipment only).
AKRON® STANDARD HI LO TILT TABLE Models 8622, 8622T, 8631, 8631T, 8632, 8632T
SERVICE MANUAL 794-020
General Maintenance including Gas Strut It is recommended that the following checks and adjustments are carried out at minimum of twice a year and more frequently if the couch is in constant use. 1.
The framework of the couch is of steel construction and coated with an epoxy paint finish. This is resistant to most cleaning substances.
2.
The major pivot points need to be lubricated sparingly with oil. Care should be taken to keep oil away from the upholstery.
3.
All nuts should be checked and tightened where necessary Care should be taken not to over tighten the nuts on the pivot points as this may cause them to bind.
4.
Air tubes should be checked to ensure that they are not pinched.
5.
Disconnect the mains supply and check the following; Note: - all electrical should be carried out by a suitably qualified person. Electric cables and mains plug should be inspected for damage and replaced where necessary. In addition, electrical safety checks for earth continuity (class I equipment only) and earth leakage checks should also be carried out. The correct value fuse of 5 amps and ASTA approved to BS1362 MUST be used.
6.
The upholstered top is manufactured using fire retardant vinyl. This tends to go brittle if oil or grease (including body oils) are left on it. The upholstery should be cleaned with warm soapy water after use. The use of detergents is not recommended although a suitable sterilisation fluid is acceptable. Use of a couch cover or towel will help prolong the life of the upholstery.
7.
Woodscrews, used to secure the upholstery, should be checked and tightened or replaced where necessary.
8.
The hinge pins on the head and foot sections should be checked to ensure that they have not moved within the hinge tubes. Ensure Circlip is located fully in groove in pin. If the Circlip is not located correctly push firmly into groove to secure pin.
9.
Gas strut controls should be checked for a small amount of clearance between the operating flap and the release pin, throughout the range of movement. Should clearance be inadequate, or the top sinks whilst in use, the following adjustments should be made; firmly grasp the body of the strut and rotate in an anti-clockwise direction. Check for clearance and repeat as necessary. Should the gas strut fail to operate, refer to the above adjustment but rotate in a clockwise direction. 1
PARTS LIST HI LO TILT TABLE BASE ASSEMBLY 2G6001Z – Issue 08 Reference Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Description Mid Section Rear H Section Link Arm Base Frame Front H Section M10 x 115mm Bolt 100mm Double Locking Castor M10 x 100mm Hex Bolt M12 x 30mm Hex Set Screw M10 Nyloc Nut M10 Flat Washer M12 Nyloc Nut M12 Spring Washer M12 Flat Washer M10 Nut Cap 1" x 1" x 10-14G Insert 11/2" x 3/4" x 16G Insert 11/2" x 1 1/2" x 10-14G Insert 2" x 1" x 10-14G Insert Bronze Flanged Bush Huntleigh Akron Label
PARTS LIST HI LO TILT TABLE HYDRAULIC/MANUAL KIT 2G6007Z – Issue 13 Reference Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
Description Single Pedal Pump Mounting Bracket Pump Ring Gas Strut Operating Lever Push Rod Push Rod Mounting Rod Pivot Shaft Gas Strut Pin Auxiliary Gas Strut Bracket Gas Strut Shroud Front Mounting Bracket Gas Strut Operating Shaft Nylon Spacer Nylon Spacer Nylon Spacer Hydraulic Ram Gas Strut 500N Locking Gas Strut 800N M6 x 12mm Countersunk Set Screw M6 x 12mm Grub Screw M8 x 10mm Grub Screw M8 x 30mm Hex Bolt M8 x 60mm Hex Bolt M8 x 70mm Hex Bolt M10 x 60mm Hex Bolt M12 x 60mm Hex Bolt 3 /8" Nyloc Nut M6 Shakeproof Washer M8 Full Nut M8 Nyloc Nut M8 Flat Washer M10 Nyloc Nut M10 Flat Washer M12 Nyloc Nut
PARTS LIST HI LO TILT TABLE HYDRAULIC/MANUAL KIT 2G6007Z – Issue 13 Reference Number 36 37 38 39 40 41 42 43 44 45 46
M12 Flat Washer R Clip 8mm x 32mm Spirol Pin M8 Nut Cap M12 Nut Cap 3 /8" End Cap 5 /8" Plummer Block Rod End Adjuster Pedal Rubber Raise/Lower Sticker Serial Number Label
Issue Date D.C.N.
10 2/99 897
Description
11 5/00 941
12 9/02 1024
Quantity 6 2 1 5 1 2 2 1 1 1 1
13 4/04 1109
Part Number 5L3562K 5M0800R 5M3110E 5N0028X 5N0030X 5N0300L 5P7808Z 5P8100Z 5T3200Z 5U1095Z 760.40
Issue Status 0 0 0 0 0 0 0 0 0 0 1
PARTS LIST HI LO TILT TABLE ELECTRIC/MANUAL 115V RAM KIT 2G6010Z – Issue 07
PARTS LIST HI LO TILT TABLE ELECTRIC/MANUAL 115V RAM KIT UL SPECIFICATION 2G6013Z – Issue 01
Reference Number 34 35 36 37 38 39 40
Description R Clip M8 Nut Cap M12 Nut Cap 3 /8" End Cap 5 /8" Plummer Block Rod End Adjuster Serial Number Label
Issue Date E.C.N.
1 2/01 967
Quantity 2 5 2 2 2 1 1
Part Number 5M0800R 5N0028X 5N0030X 5N0300L 5P7808Z 5P8100Z 760.52
Issue Status 0 0 0 0 0 0 1
PARTS LIST TILT TABLE ACCESSORY TABLE 2G6027Z – Issue 02 Reference Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Description Pivot Bar Wood Insert Fixing Frame M16 x 120mm Stud Worktable Nylon Spacer No.8 x 3/8" Flange Head Posidrive Screw No.10 x 11/2" Woodscrew M10 Flat Washer 5 /16" End Cap 21/4" x M10 Knob 16mm Handwheel 5 /8" x 16G Insert Cleat 20KG Maximum Load Label
\\MAIN_SERVER\WORKDOCS\P-LIST\2G6027Z.DOC
Quantity 1 1 1 1 1 1 5 5 2 1 2 1 4 5 1
Part Number 3A6830Z 3A9570Z 3A9640Z 3F6829Z 3F9571Z 3G9513Z 5K0305R 5K0413A 5L3362K 5N0200L 5N1582N 5N2749P 5N9206M 5T2500Z 5U1031Z
Particular care being taken to the position of the customer controls. Failure to ..... R101. ERJ6GEYJ101. 0.1W. 5%. 100. S.M.CARB. R103. ERJ6GEYJ272. 0.1W.
Jul 2, 1997 - To raise the safety side, first lift the side of the shower tray, folding the corners on the outside against the head and foot. Swing the safety side ...
Electrical Isolation. Always disconnect the board under test ..... Locate the line selector links adjacent to the power transformer and remove using suitable pliers.
If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for ..... power cord into a properly wi
Jul 2, 2000 - shown in the parts list of Service manual may cause shock, fire, or other hazards. 4. ... Some model's power circuit is partly different in the GND. ... SENSOR ..... SCREW TAPPTITE. TT2 RND 3X10 MFZN. I702. 1AT24C08PC. IC ..... POINT IN
Before replacing any of these components, read the parts list in this manual carefully. The use of substitutes .... text lines ( Packet 8/30 format 1 ). If such a code ...
Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground ...
New chassis design enable use of an interactive on screen control. ⢠The TELETEXT ... (3) Plug the power cord into the wall outlet and switch the power on.
Jul 2, 1997 - 746-38-2. This manual is intended to be used by Huntleigh Nesbit Evans approved service technicians. ..... link (04-6) out of the frame just far enough to clear the castor stem. c) Bend the ...... springs or oil in household refuse.
Service Manual. Colour Television .... When servicing, observe the original lead dress in the high .... case a measurement is outside the limits specified, there is a ...... C1840. ECUV1C104KBX. S.M.CAP. 16V 0.10mF. C1843. ECUV1H104ZFX.
NOTE : This service manual should be used in conjunction .... case a measurement is outside the limits specified, there ...... C1840 ECUV1C104KBX S.M.CAP.
To reduce the risk of electric shock, fire or injuly, do not perform any servicing other than that ... LES RÃGLAGES DE CIRCUIT DONT ...... Using the RGB IN/OUT connector on INPUT B as a ..... Remote Commander and the remoter control detector on the
It is advisable to insert an isolation transformer in the AC .... The remote control is used for entering and storing adjustments, with the ...... R2379 ERD25TJ271.
Never solder directly to the cells. Perform the soldering as ...... TR1. Transistor. 2SC3326 A,B TE85R. 01. TR2. Transistor. 2SA1162 O,Y. 01. TR3. Transistor.
... your home. The RLM Display Unit can be purchased separately for this washer. ... Spinning does not proceed until the water in the tub drains to a certain level. 2-4. ..... CABINET & CONTROL PANEL ASSEMBLY. 10. EXPLODED VIEW. A160.
9 - 1 VR-A BOARD . ..... with a 1st LO signal at the 1st mixer circuit (Q220, Q221) to ... 1st LO. B1LO. 2nd mixer. Q11. AF signals to. AF selector circuit. (IC452).
