AKRON® GYNAECOLOGY 3 Model 9932

SERVICE MANUAL 794-027

General Maintenance including Gas Strut It is recommended that the following checks and adjustments are carried out at minimum of twice a year and more frequently if the couch is in constant use. 1.

The framework of the couch is of steel construction and coated with an epoxy paint finish. This is resistant to most cleaning substances.

2.

The major pivot points need to be lubricated sparingly with oil. Care should be taken to keep oil away from the upholstery.

3.

All nuts should be checked and tightened where necessary Care should be taken not to over tighten the nuts on the pivot points as this may cause them to bind.

4.

Air tubes should be checked to ensure that they are not pinched.

5.

Disconnect the mains supply and check the following; Note: - all electrical should be carried out by a suitably qualified person. Electric cables and mains plug should be inspected for damage and replaced where necessary. In addition, electrical safety checks for earth continuity (class I equipment only) and earth leakage checks should also be carried out. The correct value fuse of 5 amps and ASTA approved to BS1362 MUST be used.

6.

The upholstered top is manufactured using fire retardant vinyl. This tends to go brittle if oil or grease (including body oils) are left on it. The upholstery should be cleaned with warm soapy water after use. The use of detergents is not recommended although a suitable sterilisation fluid is acceptable. Use of a couch cover or towel will help prolong the life of the upholstery.

7.

Woodscrews, used to secure the upholstery, should be checked and tightened or replaced where necessary.

8.

The hinge pins on the head and foot sections should be checked to ensure that they have not moved within the hinge tubes. Ensure Circlip is located fully in groove in pin. If the Circlip is not located correctly push firmly into groove to secure pin.

9.

Gas strut controls should be checked for a small amount of clearance between the operating flap and the release pin, throughout the range of movement. Should clearance be inadequate, or the top sinks whilst in use, the following adjustments should be made; firmly grasp the body of the strut and rotate in an anti-clockwise direction. Check for clearance and repeat as necessary. Should the gas strut fail to operate, refer to the above adjustment but rotate in a clockwise direction. 1

Manufacturers Details Huntleigh Healthcare Akron Products Division 1 Farthing Road Ipswich Suffolk IP1 5AP England Tel. (0) 1473 461042 Fax. (0) 1473 462924 Huntleigh Healthcare, Akron Products Division A Member of the Huntleigh Technology PLC Group of Companies © Huntleigh Technology PLC 2003.

Revision History

DOCUMENT

ISSUE

DCN No.

SIGNED

DATE

ALL PAGES

1

936

G. Mullenger

14/06/00

2M3410Z 2M3427Z

2

947/949

J. Barker

08/09/00

2M3420Z

3

951

J. Barker

23/10/00

2M3424Z

4

964

J. Barker

15/01/01

A7309 A7310

5

970

J. Barker

30/03/01

2M3427Z

6

978

J. Barker

05/07/01

2M3410Z

7

980

J. Barker

01/11/01

2M3417Z A7291

8

998

J. Barker

10/05/02

2M3410Z

9

1032

J. Barker

01/11/02

A7292

10

1037

J. Barker

19/11/02

2M3410Z 2M3427Z

11

1043

J. Barker

13/01/03

2M3410Z 2M3417Z

12

1063/1070

J. Barker

03/11/03

2M3417Z

13

1108

J. Barker

10/03/04

2M3417Z 2M3425Z 2M3426Z 2M3427Z

14

1112

J. Barker

10/12/04

2

ITEM QTY 1 1 2 2 3 2 4 1 5 1 6 1 7 2 8 1 9 2 10 2 11 1 12 1 13 3 14 2 15 6 16 4 17 4 18 2 19 2 20 2 21 4 22 4 23 10 24 2 25 2 26 1 27 1 28 1

23 23 1

23 23 23

23 2

2

23

22 19

16

23 17

23

ISSUE No. DESCRIPTION 4 H Section 0 Link Bar 0 Linking Lug 3 Short Large Wheel Base 2 Short Wheel Linking Bar 1 Hexagonal Cam 0 40x40x2.5mm Drilled Insert 2 437mm Pivot Pin 1 22mm Spacer Sleeve 0 40.5mm Spacer Sleeve 1 Short Hexagonal Cam 0 125mm Tente Directional Castor 0 125mm Tente Braking Castor 0 M6x20 Hex Set Screw 0 1/4 Flat Washer 0 3/4 Grey End Cap 0 3/4 Open Starlock 0 M6 Nyloc Nut 0 12mm Open Starlock 0 1/4"x1" Seloc Pin 0 8.5mm Grey Insert 0 40x40x2.5 Grey Insert 0 50x25x2.5 Grey Insert 1 Nylon Foot Rubber 0 Pedal Rubber 2 Huntleigh Akron Label 1 Pedal Sticker 1 Pedal Sticker

27

9 13

PART No. 3A2081Z 3A2085Z 3A3263Z 3A3675Z 3A3677Z 3F3251Z 3F3253Z 3G2089Z 3G2092Z 3G3213Z 3H3253Z 5H1204E 5H1212E 5J7658N 5L0362V 5L0707L 5L0906Z 5L2919C 5L3506Z 5M0408C 5N2100M 5N3744Z 5N3944Z 5T0028Z 5T3200Z 5U1006Z 5U1065Z 5U1066Z

25

23

5 10 11

24

21

14

21

9 16

3 17

13

17 8

20

16

18

15

7

15

26

10

15

21

19 17 22

13

21

LINKING LUG FIXING ASSEMBLY

16

22

22

6

NOTE: POSITION OF LINKING LUG (ITEM 3) IN RELATION TO WHEEL LINKING BAR (ITEM 5) IN MAIN ASSEMBLY

5 28

12 24 C

25 7 20

COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2002

DRAWN

GMullenger

CAD NO

2M3410Z

THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 18/10/2002 WRITTE N CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE

Short Large Wheel Base Assembly

Patient Positioning Solutions

1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com

REVISION STATUS ISSUE

4

5

6

7

DATE

8/01 10/02 11/02 6/03

DCN

980 1032 1043 10631070

ASSEMBLY

2M3410Z

ISSUE

7

ITEM QTY 1 2 2 1 3 1 4 1 5 1 6 1 7 1 8 2 9 2 10 1 11 2 12 1 13 2 14 2 15 2 16 4 17 4 18 4 19 6 20 6 21 2 22 2 23 4 24 16 25 10 26 1 27 4

3 17

24

26

24 17

24 24

1

24

24

24

22

23

17

24

19 17

25

20 25

1

22 24

13

5 16

24

23 4

25

PART No. 3A3181Z 3A3602Z 3A3678Z 3A3681Z 3A3682Z 3F3684Z 3G2090Z 3G2091Z 3G2092Z 3G3211Z 3G3212Z 3G3604Z 3G3605Z 3G3686Z 5J7666A 5K1238U 5K1241U 5L0362V 5L0707L 5L0906Z 5L2919C 5M0300R 5N0948Z 5N2100M 5N3944Z 5T7900Z 796.237

ISSUE No. DESCRIPTION 2 Hinge Pin 7 Mid Frame Assembly 1 Electric Back Rest 1 Gynae 2/3 Tilt Frame 1 Sliding Debris Tray Holder 0 Gynae 2/3 ABS Guard 2 335mm Pivot Pin 0 161.5mm Spacer Sleeve 1 22mm Spacer Sleeve 2 306mm H Section Pivot Pin 1 10.5mm Spacer Sleeve 2 369mm Pivot Pin 0 42mm Spacer Sleeve 0 21mm ABS Guard Spacer 0 M6x60 Hex Ht Bolt 0 M6x25 Pan Head Set Screw 0 M6x40 Pan Head Set Screw 0 1/4 Flat Washer 0 3/4 Grey End Cap 0 3/4 Open Starlock 0 M6 Nyloc Nut 0 1/4 R Clip 0 1"x1"x14G Insert 0 8.5mm Grey Insert 0 50x25x2.5 Grey Insert 0 Debris Tray 0 Bush

24 24 21

25

8 13

14

24

20 19

18 18

16 24

15 23

16

25

14

23

18

24

25

16

24

12

6

18

25

2

15

21

25 9 7 8

27

19

27

27

20

27

CHECKLIST 19

9

DCL181

20

20 11 19

10 11

C 25

19 20

25

COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2004

DRAWN

GMullenger

2M3417Z THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 01/06/2004 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE

CAD NO

Gynae 2/3 Top Frame Assembly

Patient Positioning Solutions

1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com

REVISION STATUS ISSUE

3

4

5

6

DATE

3/02 7/03 3/04 6/04

DCN

998

ASSEMBLY

2M3417Z

1070 1108 1112 ISSUE

6

26

5 5 RAM LEADS RUNNING BACK TO CONTROL BOX ARE TO BE SECURED USING 3 OFF 5S0315Z CABLE TIES (ITEM 31), 2 OFF 5S0318Z PUSH MOUNTED CABLE TIES (ITEM 32), 1 OFF LENGTH OF SMALL CURLY WRAP 5S0326Z (ITEM 33) AND 1 OFF LENGTH OF LARGE CURLY WRAP 5S0327Z. (ITEM 34).OBJECTS NOT SHOWN

35

10

12 17 19 7

14

24 23

21

24 5

19

5

4

28 23

3

25 21

12

21

24 36

28

5 28

17

27

20 27

21

4 17

19

28

21 20

27 27

9

15

23

23

16

25

24 5

27

PART No. 3A2088Z 3A3375Z 3A3376Z 3A3377Z 3G3378Z 3G9437Z 5F0907Z 5F0924Z 5F0926Z 5F0927Z 5J7866A 5J7870A 5J8264A 5J8266A 5J8267A 5K0407X 5K1137N 5L2855K 5L2865K 5L3119C 5L3162K 5L3503Z 5L3519C 5L3562K 5L5719B 5M3145S 5N0056X 5N0058X 5S0216Z 5S0315Z 5S0318Z 5S0326Z 5S0327Z 5S0335Z 713.91 760.43 S6615

ISSUE No. DESCRIPTION 0 H Section Fixing Pin Motor Mounting Bracket 0 0 Control Box Support 0 Control Box Plate 0 5mm UVPC Spacer 0 20mm UVPC Spacer 0 Linak CB12-03-AT-24 240v Control Box 0 LA343100+0X20004X Actuator 0 LA311700+1010004X Actuator 0 LA311800+1010004X Actuator 0 M8x60 Hex Ht Bolt 0 M8x80 Hex Ht Bolt 0 M12x50mm Hex Bolt 0 M12x60mm Hex Bolt 0 M12x65mm Hex Bolt 0 No10x1/2 Pan Head Set Screw 0 M5x20 Pan Head Set Screw 0 5mm Shakeproof Washer 0 M5 Flat Washer 0 M8 Nyloc Nut 0 M8 Washer Flat Form B 0 12mm Starlock Capped 0 M12 Nyloc Nut 0 M12 Washer Flat Form B 0 6BA Nut 0 8mm E Clip 0 M8 White Nut Cap 0 M12 White Nut Cap 0 1.5mm Earth Wire 0 Cable Tie 0 Push Mounted Cable Tie 0 Small Curly Wrap (0.6m) 0 Large Curly Wrap (0.7m) 0 5mm Crimped Eyelet 0 12mm Clevis Pin 1 Serial Number Label 0 Linak Mains Cable

5 20

20

24

24 18

3

5

24

29

19 3

21

13

34

ITEM QTY 1 1 2 1 3 4 4 2 5 8 6 2 7 1 8 1 9 1 10 1 11 2 12 4 13 1 14 1 15 2 16 1 17 4 18 2 19 8 20 6 21 12 22 2 23 4 24 8 25 4 26 1 27 6 28 4 29 1 30 3 31 2 32 1 33 1 34 2 35 1 36 1 37 1

24

21

18

15

21 27

8 20

1

11 6

21

22 6

22

2 21

CHECKLIST

11

DCL185

37

C

COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2004

DRAWN

GMullenger

2M3425Z THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 07/06/2004 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE

CAD NO

Patient Positioning Solutions

230v Triple Linak Ram Kit For Shrouded Base

1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com

REVISION STATUS ISSUE

1

2

3

4

DATE

9/99 12/99 3/00 6/04

DCN

908

ASSEMBLY

2M3425Z

911

930 1112 ISSUE

4

26

5 RAM LEADS RUNNING BACK TO CONTROL BOX ARE TO BE SECURED USING 3 OFF 5S0315Z CABLE TIES (ITEM 31), 2 OFF 5S0318Z PUSH MOUNTED CABLE TIES (ITEM 32), 1 OFF LENGTH OF SMALL CURLY WRAP 5S0326Z (ITEM 33) AND 1 OFF LENGTH OF LARGE CURLY WRAP 5S0327Z. (ITEM 34).OBJECTS NOT SHOWN

5 35

10

12 17 19 7

14

24 23

21

24 5

19

5

4

28 23

3

25 21

12

24 28

5

21 28

27

17

20 27

21

4 17 19

3 19 3

24

5 36

24

24 18

21

13

34 29 28

9

15

23

23

16

25

24 5

27

20 20 27 27

PART No. 3A2088Z 3A3375Z 3A3376Z 3A3377Z 3G3378Z 3G9437Z 5F0909Z 5F0924Z 5F0926Z 5F0927Z 5J7866A 5J7870A 5J8264A 5J8266A 5J8267A 5K0407X 5K1137N 5L2855K 5L2865K 5L3119C 5L3162K 5L3503Z 5L3519C 5L3562K 5L5719B 5M3145S 5N0056X 5N0058X 5S0216Z 5S0315Z 5S0318Z 5S0326Z 5S0327Z 5S0335Z 713.91 760.49 S6615

ISSUE No. DESCRIPTION 0 H Section Fixing Pin Motor Mounting Bracket 0 0 Control Box Support 0 Control Box Plate 0 5mm UVPC Spacer 0 20mm UVPC Spacer 0 Linak CB12-03-AT-24 115v Control Box 0 LA343100+0X20004X Actuator 0 LA311700+1010004X Actuator 0 LA311800+1010004X Actuator 0 M8x60 Hex Ht Bolt 0 M8x80 Hex Ht Bolt 0 M12x50mm Hex Bolt 0 M12x60mm Hex Bolt 0 M12x65mm Hex Bolt 0 No10x1/2 Pan Head Set Screw 0 M5x20 Pan Head Set Screw 0 5mm Shakeproof Washer 0 M5 Flat Washer 0 M8 Nyloc Nut 0 M8 Washer Flat Form B 0 12mm Starlock Capped 0 M12 Nyloc Nut 0 M12 Washer Flat Form B 0 6BA Nut 0 8mm E Clip 0 M8 White Nut Cap 0 M12 White Nut Cap 0 1.5mm Earth Wire 0 Cable Tie 0 Push Mounted Cable Tie 0 Small Curly Wrap (0.6m) 0 Large Curly Wrap (0.7m) 0 5mm Crimped Eyelet 0 12mm Clevis Pin 1 Serial Number Label 0 Linak Mains Cable

5

20 21

ITEM QTY 1 1 2 1 3 4 4 2 5 8 6 2 7 1 8 1 9 1 10 1 11 2 12 4 13 1 14 1 15 2 16 1 17 4 18 2 19 8 20 6 21 12 22 2 23 4 24 8 25 4 26 1 27 6 28 4 29 1 30 3 31 2 32 1 33 1 34 2 35 1 36 1 37 1

24

21 18

15

21

27

8 20

1

11 6

21

22 6

22

2 21

CHECKLIST 11

DCL185

37

C

COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2004

DRAWN

GMullenger

2M3426Z THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 07/06/2004 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE

CAD NO

Patient Positioning Solutions

115v Triple Linak Ram Kit For Shrouded Base

1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com

REVISION STATUS ISSUE

1

2

3

4

DATE

9/99 12/99 3/00 6/04

DCN

908

ASSEMBLY

2M3426Z

911

930 1112 ISSUE

4

ITEM QTY 1 1 4 2 3 12 4 12 5 2 6 2 7 1 8 1 9 1 10 1 11 1

10 4

PART No. 3F3255Z 5N1900M 5T0100Z 5T0200Z 5T0300Z 5T0400Z 5X4001Z 5X4002Z 5X4003Z 5X4006Z 5X4007Z

ISSUE No. DESCRIPTION 1 Extended Hexagonal Cam 0 4.5mm Grey End Cap 0 50mm Self Adhesive Hook Velcro 0 50mm Self Adhesive Loop Velcro 0 200mm Self Adhesive Hook Velcro 0 200mm Self Adhesive Loop Velcro 1 Base Cover Shroud 0 H Section Cover Shroud 0 Mid Section Front Panel Cover Shroud 1 Top Mid Section Cover Shroud 0 Mid Section Cover Shroud

5 4

6 3

8 3 6 5

3 4

4 3 2 2

1

3

3

11

4 4

2

4 4

2

3

3

3

9 4

3

7

4

CHECKLIST

DCL193 DEGREASE SHROUDING BEFORE APPLYING VELCRO STRIPS

C

COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2004

DRAWN

GMullenger

2M3427Z THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 24/06/2004 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE

CAD NO

Positive Shrouding Kit

Patient Positioning Solutions

1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com

REVISION STATUS ISSUE

4

5

6

7

DATE

7/01 10/01 11/02 6/04

DCN

0978 0981 1043 1112

ASSEMBLY

2M3427Z

ISSUE

7

PARTS LIST 2M3422Z A7303 SEAT EXTENSION 2M3422Z – Issue 03 Reference Number 1 2 3 4 5 6

Description Seat Section Loop M10x42 Brass Stud M6x40 Pan Head Set Screw M10 Half Nut 1”x1”x16G Rounded Insert 2 ¼”xM10 Knob (Red)

Issue Date E.C.N.

1 9/99 908

2 3/00 927

3 6/00 936

Quantity 1 1 4 1 2 1

Part Number 3A3683Z 3G4431Z 5K1241U 5L3319A 5N0909M 5N1560N

Issue Status 1 0 0 0 0 0

PARTS LIST A7302 SHELF ASSEMBLY 2M3423Z – Issue 04 Reference Number 1 2 3 4 5

Description Shelf Bar M5x12 Pan Head Set Screw R Clip 3/4" x 16G Grey Insert Gynae Shelf

Issue Date E.C.N.

1 9/99 908

2 12/99 911

3 3/00 927

Quantity 1 6 2 2 1

4 6/00 936

Part Number 3A3697Z 5K1135T 5M0800R 5N9251M 5U1600Z

Issue Status 0 0 0 0 0

PARTS LIST A7301 SINGLE ADJUSTABLE ARM SUPPORT 2M3424Z – Issue 04 Reference Number 1 2 3 4 5 6 7 8 9 10

Description Leg Support Assembly Arm Support Pivot Plate M12x60 Steel Stud M6x6 Grub Screw No 10x1" CSK Set Screw M12 Half Nut Tee Handle 1347 Black Ball Joint Joint Nut Arm Rest Moulding

Issue Date E.C.N.

1 9/99 908

2 03/00 927

3 06/00 936

Quantity 1 1 1 1 4 1 1 1 1 1

4 1/01 964

Part Number 3A3688Z 3A3696Z 3A9415Z 5J7653Z 5K0411Z 5L3519C 5N1630Q 5T0051Z 5T0053Z 5T0066Z

Issue Status 0 0 0 0 0 0 0 0 0 0

ITEM QTY 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 3 9 2 10 2

PART No. 3A3630Z 3F3632Z 3F3633Z 3G3620Z 3G3631Z 3G3634Z 5G4400Z 5K1238U 5S0333Z S5020

ISSUE No. 1 0 0 0 0 0 0 0 0 0

DESCRIPTION Paper Roll Holder Frame 7/8 End Cap with 12.7mm Hole 7/8 End Cap with 15.875mm Hole 15.5mm UVPC Spacer Sprung Paper Roll Tube Sprung Paper Roll Holder Sleeve 40x8.5x0.8 Spring M6x25 Pan Head Set Screw Low Shrink Temperature 7/16x16-18 Rubber Grommet

4

10 8

1

2

7 9

10

8

6 8

5

9 3

C

COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2002

DRAWN

GMullenger

CAD NO

A7292

THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 07/11/2002 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE

Paper Roll Holder

Patient Positioning Solutions

1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com

REVISION STATUS

1

ISSUE DATE

2

3

11/96 10/97 11/02

DCN ASSEMBLY

A7292

-

848 1037 ISSUE

3

PARTS LIST LEG SUPPORT A7309 – Issue 02 Reference Number 1 2 3 4 5 6 7

Issue Date E.C.N.

Description Leg Support Assembly M12x60 Steel Stud M12 Half Nut Tee Handle 1347 Black Ball Joint Joint Nut Leg Rest Moulding

1 03/00 927

2 03/01 970

Quantity 2 2 2 2 2 2 2

Part Number 3A3688Z 3A9415Z 5L3519C 5N1630Q 5T0051Z 5T0053Z 5T0067Z

Issue Status 0 0 0 0 0 0 0

PARTS LIST ARM LOOPS A7310 – Issue 02 Reference Number 1 2 3

Issue Date E.C.N.

Description Arm Rest Support Bracket M6x20 Cap Head Screw Arm Rest Loop

1 03/00 927

2 03/01 970

Quantity 2 4 2

Part Number 3A3690Z 5J7658R 5T0062Z

Issue Status 0 0 0

PARTS LIST SINGLE DIN RAIL ASSEMBLY A7311 – Issue 01 Reference Number 1 2 3 4

Issue Date E.C.N.

Description Din Rail Spacer Din Rail Din Rail Plate M8x40 CSK Allen Screw

1 03/00 927

Quantity 2 1 2 2

Part Number 3A3692Z 3F3691Z 3F3693Z 5J7862U

Issue Status 0 0 0 0

PARTS LIST Magnetic 3 Channel Footswitch Assembly A7314 – Issue 01 Reference Number 1 2

Issue Date E.C.N.

Description Magnetic 3 Channel Foot Switch Push in Rubber Foot

1 02/00 928

Quantity 1 12

Part Number 5F9105Z 5T4400Z

Issue Status 0 0

ITEM QTY 1 2 2 4 3 4 4 8 5 12 6 8 7 1 8 1

PART No. 3F2096Z 5J7862A 5J7863A 5L3119C 5L3162K 5N0028X 5T0015Z 5T0016Z

ISSUE No. 2 0 0 0 0 0 0 0

DESCRIPTION Arm Rest Mounting Plate M8x40 Hex Ht Bolt M8x45 Hex Ht Bolt M8 Nyloc Nut M8 Washer Flat Form B M8 Nut Cap Left Hand 100mm Arm Rest Right Hand 100mm Arm Rest

7

7

2

1 5 4

8 6 6 4 5 1

3 8

5 5 4 6

6 4 2

5 5 3

C

COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2002

DRAWN

GMullenger

CAD NO

A7291

THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 28/02/02 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE

Fold Down Arm Rest Module

1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com

REVISION STATUS

1

ISSUE DATE

2

09/96 02/02

DCN ASSEMBLY

A7291

-

998 ISSUE

2