For container part OP-093/01 (Student 01). For container part OP-087 (MarS I). For container part OP-103 (Real-X). For container part OP-095 T (MarS-T).
Procedure for setting the reserve closing loop Designed for packing and closing the container part of reserve parachute - without Automatic activation device AAD - with Automatic activation device AAD: m2, CYPRES, VIGIL For container part OP-093/01 (Student 01) For container part OP-087 (MarS I) For container part OP-103 (Real-X) For container part OP-095 T (MarS-T)
1. edition
In Jevíčko 01/2013
1
Page: 2
1. Pre-stretching the reserve closing loop of the reserve parachute (hereinafter referred to as the closing loop) Perform the pre-stretching of the closing loop by attaching the reverse side of the closing loop by means of suitable method (e.g. clove hitch) to suitable aid tool and manually pre-stretch the closing loop with approx 300 N force of the applied closing loop.
2. Procedure for threading the closing loop of the reserve parachute to the mat a) Without Automatic activation device AAD Insert the pre-stretched closing loop to the mat attached by usual way. b) With Automatic activation device AAD Insert the pre-stretched closing loop to the mat attached to the applied device using a method specified in the device manual.
3. Installation of the closing loop to the reserve parachute container part Install the closing loop by means of specified method to the reserve parachute container part.
4. Applied tools for packing and closing the reserve parachute container part: Additionally to the basic packing tools (packing bar, auxiliary packing needle, tool for threading the auxiliary packing cord through the pilot chute) it is permitted to use auxiliary packing tools (e.g. packing pin) for simpler closing of the container part flaps of the reserve parachute.
5. Packing of the reserve ram air canopy to the reserve parachute container part Place the webbings of the reserve parachute and folded reserve canopy placed in the free back by means of the specified method to the container part of the reserve parachute. Use the packing line to thread the closing loop the through the grommets in the free bag and through the container part flaps of the reserve parachute number 1 and 2. Secure the closing loop by means of auxiliary packing needle. Thread the auxiliary packing line through the applied pilot chute. Place the free bag connecting binding by means of specified method and place the pilot chute to the specified location.
2
Page: 3
6. Placing the round reserve canopy to the reserve parachute container part Place the webbings of the reserve parachute and folded reserve canopy by means of the specified method to the container part of the reserve parachute. Use the packing line to thread the closing loop between the folds of the folded round reserve canopy and container part flaps of the reserve parachute number 1 and 2. Secure the closing loop by means of auxiliary packing needle. Thread the auxiliary packing line through the applied pilot chute. Use the pilot chute to thread the auxiliary packing needle and place the pilot chute to the specified location.
7. Placing the pilot chute to the reserve parachute container part Press the pilot chute, release the pilot chute canopy material and secure the compressed pilot chute in the specified position by means of auxiliary packing needle. Place the released material of the pilot chute canopy by means of specified method on the pilot chute periphery. Secure the auxiliary packing cord and the pilot chute with the packing part of the reserve parachute by means of suitable method on the packing mat.
The photo of the packing mat Pre-stretch the auxiliary packing line by force approx 220 ÷ 240 N and measure the distance between the upper grommet end of the applied pilot chute and the closing loop top. If the container is packed: a) Without Automatic activation device AAD Measured distance should be between 17 mm and 22 mm. b) With Automatic activation device AAD Measured distance should be between 25 mm and 30 mm. If it is out of this range, adjust the closing loop length! Close the container part in accordance with the instructions manual. After closing the container part, perform the force inspection required for shifting the closing needle of manual ripcord pin of the reserve parachute. If the force is over 45 N, extend the length of the closing loop. The resulting force required for threading the needle must be between 32 ÷ 45 N, which ensures that upon pulling the manual ripcord pin of the reserve parachute, the force specified by the standards will not be exceeded.
Apr 15, 2009 - 2. Cut a piece of nylon thread approximately. 20â (50 cm) long. ... Before we get into loop lengths, let's assume bulk management, has been ...
TIP: The deeper and wider that you can get the. ânestâ the easier it will be to match the suggested loop lengths. Canopy Size. Loop Length. PDR 106. 3.00â +/- ¼â.
drogue riser at one end and to the main top flap at the other end. ⢠A 2nd grommet is inserted into the top flap in line with the existing grommet. ⢠An extension ...
Click on Login. Enter username (Default username = admin). Enter password (Default password = admin or blank for Optus configured modems). Click OK ...
Icon Sizing Chart for the SmartLPV Reserve. Icon Size. I1. I2. I3. I4. I5. I6. I7. S7. S8. S9. Smart Size. 99. Easy Fit. 110. Standard Fit. Easy Fit. 120. Tight Fit.
Source: Calculated by authors, from data from World Bank 2017, PIK 2017, and GCF 2018d. 0%. 10 .... share” frameworks for international climate finance (see,.
les résultats scolaires des enfants d'immigrés et réfléchir aux actions qui ... et de moindres chances de fréquenter des établissements d'enseignement ...
questions and explain their answers as part of the process of constructing a ...... Audits ensure that various accounting rules and investment regulations are followed. .... As an investor in the 21st century, you have an array of investment choices
Any numeric variable in the output data set can be used to specify the ... A cluster containing at least two objects but not all of them is a branch. ... The TREE procedure creates tree diagrams from a SAS data set containing the tree ... In the foll
Output 41.1 on page 1319 shows a default univariate analysis for student exam ..... PROC UNIVARIATE uses order statistics (ranks) to compute the confidence.
The program for this plot is in Example 4 on page 839. For more .... In addition, regression lines and confidence limits will represent only part of the original data.
The PRINT=FREQ option displays output in the appropriate raw or natural units. ...... sq RsD. -1 c B squared cosines. Supplementary column diag(sq Cs -1r.
1. Listed by Town, Amount, Account Number. Account. Obs. Company. Town ..... The data set ACCOUNT contains the name of each business that owes money, ...
Page 1 ... Given a data set with p numeric variables, you can compute p principal ...... 20 through 30 (there is a missing rank in one of the variables, WashPost).
Mesh topology (â quadrature nodes) is changing in time reconstructing point values at ..... CWENO on triangular unstructured meshes. Thanks to M. Dumbser!
Source: Fisher (1936) Iris Data'; footnote2 j=r 'GR29N05(b) ';. Generate the plot. NONEEDLE suppresses the line drawn from the x-y plane to the plot point.
968. Chapter 24. The CORRESP Procedure. The CORRESP Procedure ..... r PD. -1 c . In all of the preceding pairs, distances between row and column points ...... The correct bibliographic citation for this manual is as follows: SAS Institute Inc.,.
control the graphics appearance with PLOT statement options and with ...... The goal is to develop an equation to predict fitness based on the exercise.
By default, the PLOT statement scales the axes to include the maximum and minimum data values and displays a ... Plots with two vertical axes have a right vertical axis that can. 3 display the same ...... Appointment Book' j=r 'GR21N08(a) ';.
of explanatory variables and p = Pr Y = 1 | x is the response probability to be modeled ..... The variable Freq represents the frequency of occurrence of each com-.
