START ENGINE SET BLOWER SPEED CONTROL SWITCH TO ”HI” POSITION SET TEMPERATURE CONTROL SELECTOR TO ”MAX COOL” POSITION PUSH A/C SWITCH RACE ENGINE AT 1,500 RPM
6. (a)
INSPECT PRESSURE SWITCH OPERATION Disconnect the connector.
3.
1 2
3 4
I11230
(b) Low Pressure Side
ON (Continuity) 22.5 kPa (2.3 kgf/cm2, 33 psi)
196 kPa (2.0 kgf/cm2, 28 psi) OFF (No Continuity) High Pressure Side ON (Continuity) 3,140 kPa 2,250 kPa 2, (32.0/kgf·cm 2 (26 kgf/cm , 455 psi) 370 psi) OFF (No Continuity) I08493
Inspect pressure switch continuity (Magnetic Clutch Control). (1) Connect the positive (+) lead from the ohmmeter to terminal 4 and the negative (-) lead to terminal 1. (2) Check continuity between terminals when refrigerant pressure is changed, as shown in the illustration. If continuity is not as specified, replace the pressure switch.
(c)
ON (Continuity) OFF (No Continuity) 1,520 kPa 2 (15.5/kgf/cm , 220 psi) 1,226 kPa 2 (12.5 kgf/cm , 178 psi) I05079
Inspect pressure switch continuity (Condenser Fan Control). (1) Connect the positive (+) lead from the ohmmeter to terminal 2 and the negative (-) lead to terminal 3. (2) Check continuity between terminals when refrigerant pressure is changed, as shown in the illustration. If operation is not as specified, replace the pressure switch.
INSPECT SWITCH CONTINUITY. (a) Using an ohmmeter, check that no continuity exists be- tween the terminal and switch body when the coolant temperature is ...
High-Low pressure switch. If the refrigerant pressure becomes too high (due to blockage), or too low (due to leakage), the A/C triple pressure switch sends a ...
5A at 250VAC; 1A at 50VDC; 0.2A at 250VDC. The electro-hydraulic pressure switch provides an electric signal when the sensed pressure goes above or below.
Sep 12, 2014 - 5. Output Functions. 5.1 Switching Outputs. The EDS 3000 can have 1 or 2 ..... 300 g. Note: FS (Full Scale) = related to the full measuring range ...
Note: This switch does not have an adjustable differential. Check switch operation after resetting. Nota: Este interruptor no tiene un diferencial ajustable.
CIRCUIT DESCRIPTION. The door unlock detection switch is built in the door lock motor assembly. This switch is ON when the door lock knob is in the unlock ...
CIRCUIT DESCRIPTION. The key unlock warning switch goes ON when the ignition key is inserted in the key cylinder and goes OFF when the ignition key is ...
shock and vibrations. The electronics are protected from ... Tube clamp. ⢠Safe mounting with a rugged SCSD-S27 clamp ... Shockproof. Instrument Features ...
Settable final pressure. Characteristics. Reliable/safe. Pressure is captured by a measuring cell with long-term stability. Any functional error is monitored and can ...
When you push the SinkTop Switch⢠button, you switch electrical power between the two outlets on the power module. This feature allows a second appliance ...
(b) Install the coil spring to the shock absorber. HINT: Fit the lower end of the coil spring into the gap of the spring low- er seat. (c) Install the upper insulator with ...
When installing the front seat outer belt, take care that the wiring does not interfere with other parts and is not pinched between other parts. 1. INSTALL FRONT ...
INSTALLATION. 1. INSTALL ELECTRIC COOLING FAN TO RADIATOR. Install the cooling fan with the 3 bolts. Torque: 7.5 N·m (80 kgf·cm, 66 in.·lbf). 2. INSTALL ...
(a) Fasten the front seat belts. (b) Drive the car at 10 mph (16 km/h) and slam on the brakes. Check that the belt locks and cannot be extended at this time. HINT:.