main board spread a thin film of Thermal Joint Compound on the surface which contacts the chip tabs. Be sure to use screws (4-40 x 3/16â) that do not protrude.
Mounting the LX200 Main board 1. Examine the reverse side of the main printed circuit board (PCB) to ensure the 4 Nylon insulating washers and the 2 Nylon stand offs are firmly in place as shown in Fig 3. 2. If mounting the Aluminum Heat Sink to the motor driver chips U17 and U18 on the main board spread a thin film of Thermal Joint Compound on the surface which contacts the chip tabs. Be sure to use screws (4-40 x 3/16”) that do not protrude through the heat sink and contact the wires or electronic components underneath. 3. Set the PCB in place and install the 4 Allen head mounting screws. (Fig1 1,2,3,4) 4. Spread thermal joint compound (Thermal Grease) on the bottom of the two 8.2 Ohm 10Watt Motor Resistors Mount the Resistors by attaching the clip against the side of the base using double sided sticky tape and RTV adhesive (Silicone also works well). 5. Plug the RA Motor connector onto the PCB 7 pin jack J2. 6. Plug the 34 Conductor Ribbon cable connector onto the double row header J1. Be very careful the cable aligns with the header as any misconnection will harm the electronics when powered up. DOUBLE CHECK THIS CONNECTION. 7. Spread a thin film of thermal joint compound (Thermal Grease) on the surface of the Aluminum Heat Sink which attaches to the base plate as shown in Fig 2. 8. Double check all connections and make sure the mounting screws are tight.
Fig 1 Main PCB Mounted in base
Fig 2
Fig 3 Main PCB Reverse Side
W1 – W4 Nylon Insulating Washers .312 OD x .140 ID x .032 H S1 – S2
Jan 15, 2005 - U18 Pin 1 to 3 = 19K Ohm - No Motor. R9 is 2 Ohm older boards. R9 is 8 Ohm 10W with wire leads mounted off board. R4 is 8 Ohm 10W with ...
write to me by E-mail:[email protected] to the get lastest distinguishing messages. ...... address. Perform any required initialization before the Coprocessor test next.
999 records - Download the HyperTerminal configuration file (for MegaSquirt) by clicking on the link. (then go to step D.), ..... MSD 6A: depends on trigger type,.
The leading edge features "Shark's Teeth" which enhance the flight characteristics and allow for soft, on-heading openings. Lightly loaded this canopy is suitable ...
Install the left and right adjustable mounting brackets to the ... Note: lower round security rings on the mounting ... center on the video wall frame left to right and.
acheter des boulons longs 4 x 65 mm pour remplacer les boulons 4 x 60 mm fournis. Ceci permet de s'assurer que l'on a un engagement sur le filetage d'au moins 12 mm. Phone: +61 (0)2 4271 8244. Email: [email protected]. Web: www.barkbusters.net. Ma
Schablone / Template. 7. Copyright by. SW-MOTECH GmbH & Co. KG & BAGS-CONNECTION GmbH & Co. KG. Irrtümer und Ãnderungen vorbehalten. Technische und Design-Ãnderungen vorbehalten. Errors and omissions expected. Technical and design-modifications ar
I x1 x1 x1 x2 x4. 5 mm. 3 mm x2 x3 x2 x4. I. 5 mm. 5 mm. 3 mm. Focal-JMlab® - BP 374 - 108, rue de l'Avenir - 42353 La Talaudière cedex - France - www.focal.com - Tel. (+33) 04 77 43 57 00 - Fax (+33) 04 77 43 57 04. SCEB-140410/1 - codo1463. • Acces
This mirror includes four D-rings on the back for mounting to a wall in either orientation ... fabriqués à partir de béton, de brique ou de plâtre, veuillez ... Le matériel de montage est conçu pour être fixé à une cloison sèche ou à un poteau mural.
dificilmente. y no puede utilizar el cable electrico como medio de soporte. EI accesorio no se puede armar en un techo con caler radiante. Fluorescent Fixture ...
up from finished floor level. (Height ... flanged fitting and inlet seal to back of inlet. 5. Replace ... Guide excess wire back through the hole in inlet bracket and.
Si vous avez des questions pour poser ou les préoccupations pour exprimer, connecter au 1-800-664-0042 de 8H00 à 16H30 (Heure centrale) (Opérateurs de ...
Rev. 2: 07/09. For questions or concerns, please call the Safco Consumer Hot Line 1-800-664-0042 available Monday-Friday 8:00 AM to 4:30 PM (Central Time) ...
TamoSoft: Network Tools & Security Software // Download // Main Downloads. Your Cart ... Operating Systems. Download ... Manuals in PDF format and help.
