Input Voltage. (2). Max Input Current. (3). Max Single Cell Full Voltage. (4). Minimum Chargeable Battery Voltage: 1.25V (the charger will indicate if a single.
Li-Polymer Battery Charger, 2-cell to 3-cell: E-Sky EK2-0851 Specifications:
Digital Products Company www.dpcav.com
(1). Input Voltage: DC11.5~13.5V (2). Max Input Current :1500mA (3). Max Single Cell Full Voltage: 4.2V±0.05V (4). Minimum Chargeable Battery Voltage: 1.25V (the charger will indicate if a single cell voltage is lower than this parameter) (5). Defective Battery Detection Time: 3 MIN (LED indicates when the battery is damaged) (6). Typical Charge Current: 750 mA (7). Compatible Battery Voltage: 11.1V 1000mAh / 8.4V 900mAh Li-Polymer battery (8). Full Charge Voltage: 8.4 ±0.1V (2-cells); 12.6V ±0.1V (3-cells)
Charge process: 1. Connect the charger with the power supply. The red power indicator will light up, which indicates that the power connection is normal. 2. Connect the 2-cell or 3-cell Li-polymer battery with the charge ports of charger respectively. The green charging indicator flashes to indicate that the battery is recharging. 3. Green indicator stops flashes shows that the battery is fully charged. Note: Charge time cannot exceed 120 minutes. Charging Precautions: 1. After connecting the power, the red indicator will light. Otherwise, it indicates that the power connection is incorrect. 2. The Green indicator will flash after connecting the battery to the charger, which indicates that battery is charging. If green and red indicators flash simultaneously, it indicates the error with battery; please check whether the battery has been damaged. If the green indicator goes out and the red indicator flashes, it shows that the charger is under protection mode; please disconnect the power for 3 seconds and switch the power on again. 3. Green indicator will be on constantly after the recharge is complete. If the battery has not been unplugged for a long time after a recharge, the battery would be recharged when single battery voltage is lower than 4.15V after self discharge. 4. Keep away from children and take the battery out of the product while charging. 5. Fire or serious injury may result under certain conditions. Please follow the instructions. NEVER leave equipment unattended while charging. 6. Keep the battery charged in a cool and ventilated place. Keep away from heat source, flammable and explosive materials.
If the Lithium Polymer pack is not damaged, discharge it to 1V per cell (2S pack = 2V, 3S pack = 3V). You may use a 150 ohm 2W resistor (from. Radio Shack or ...
Extensive research and development makes the Charger a state- .... settings. The trimmers have a deceleration range of 2,5 cm and 7 cm of acceleration.
Jan 5, 2014 - Battery packs must be able to be disconnected within the Car quickly .... Tianco. ORCA. Infinite. # OB4890P5. Orca. LiPo 2S 7.4v. 35.5 Wh. 90C.
Ecarts de conversion Actif (V) ... Production vendue [biens et services] ..... (5) correspond à la mise en service de gros travaux pour un montant de 4 403 k⬠( les ...
Système de communication mains libres de série avec lecture audio ... les renseignements disponibles au moment de l'autorisation de publication (août 2017).
Jan 5, 2014 - It is strictly NOT ALLOWED, to charge 2S LiPo Batteries to give an output voltage exceeding 8.40v. LiPo 'Sack' must be used when charging .
Jan 5, 2014 - It is essential that batteries on this list are charged using a 2S LiPo ... It is strictly NOT ALLOWED, to charge 2S LiPo Batteries to give an output ...
