INSTRUCTION ORDER NO. 122 GENERAL DESCRIPTION The coax arm is 24" long and is designed to keep coax cables, rotator cables, etc. from being damaged while the crank-up towers are being raised or lowered. Each arm is clamped at the top of each tower section by a U-bolt. This allows the coax arm to be used on tower legs up to 11/a" in diameter and will fit all Hy-Gain towers as well as many other models. 1t is recommended that one coax arm be used for each tower section. INSTALLATION AND ASSEMBLY The most important thing to remember is to stagger the placement of all arms around the tower structure. DO NOT install the coax arms directly over each other. This staggering method will allow the coax to loop easier without damage.
Figure 1 Overall Installation
Figure 2 Proper Placement
Attach the coax arm to the smallest tower section as shown in Figure 2. Each remaining coax arm is attached the same way. Make sure the end of the arm does not extend into the tower sections. This will prevent the tower sections from extending properly and may damage your system. Refer to Figure 2 for proper installation. The coax should be run through the loop at the end of the coax arm.
Measure each tower section and add 18 to 24 inches to the coax before tying the coax fast to each coax arm. There should be a loop of coax in each section. Refer to Figure 3. Allow the coax to loop around its top of the tower. There should be just enough coax to allow the rotator to turn the antenna one and one half turns in any one direction. See Figure 4. Inspect coax monthly for cuts or nicks in the insulating jacket.
3 The canopy used in this assembly is the 4.8 m Aeroconical® (U.S. Patent ... Practice climbing out of your aircraft with your parachute on whilst on the ground. ..... 3.1 Attach the 64 mm (2.5 in) cord loop attached round the apex lines over the ..
(Figure 1.) b. With the cap vent pointing left, slightly lift the manifold cap, making sure that it is separated from the diaphragm. Then carefully rotate it until cap vent ...
pump with a rotating driven impeller shaft in place of an older pump with a pinned ... into groups that are identified by using engine crankshaft rotation, magneto ...
It will be the sole responsibility of the altering agent to attach the necessary service parts information along with FAA Form 337, or its equivalent, to the ...
Read and Save Ebook la citadelle du temps suivi de no contact order as PDF for free at Online Ebook Library. Get la citadelle du temps suivi de no contact order ...
mA. W. W. °C. °C. Characteristic. Symbol. Test Conditions. Min. Max. Unit. Collector Emitter Sustaining Voltage. Collector Cutoff Current. Collector Cutoff Current.
Jul 7, 2004 - Dimensions: 314 x 363 x 30 mm. ..... function of f-1 a straight line should result with the ... average value of v which you found in Exercise 1.
The following chart shows the established time between overhaul (TBO) for ... be overhauled at 1500-hour intervals or at recommended TBO, whichever is lower.
18 avr. 2016 - Ces listes peuvent être sous format numérique. ..... le fichier vidéo de l'épreuve (format AVI) qui peut être lu par l'intermédiaire d'un logiciel ...
To use the charts on the following pages, first determine the spark plug reach and ... The table below provides a quick reference for locating a chart that lists a ...
... en maintenance comporte une gâche en plastique, celle-ci doit être remplacée par une gâche métallique et le joint d'étanchéité doit également être remplacé.
Transfer tech sheet (and bag) over to new single metal access panel. Place new panel on dishwasher and align holes in panel with holes in clips. 4. Secure single metal access panel to dishwasher using the. 2 screws supplied. 5. Replace all parts and
Siga el ajuste de la prueba de tensión de CA. 8. .... A menos que mida tensión o corriente, apague y bloquee el suministro ..... O.L. » en cas de polarisation.
