Installation Instructions Model E 21362-61BK 1. Turn breaker off for circuit on outlet where fixture is to be installed. 1. Désactiver le disjoncteur correspondant au circuit sur lequel le modèle va être monté. 2. Install mounting bracket to electrical box. 2. Installer le support de montage à la boîte électrique. 3. Wire fixture to wires in outlet box. Green wire is for Ground. 3. Fixer entre eux les fils du plafond à ceux du modèle. Vert est pour la terre. 4. Install fixture to bracket and tighten 2 nuts so that fixture meets the ceiling. 4. Installer le dispositif de fixation sur le support et faire deux noeuds afin que le dispositif touche le plafond. 5. If additional fixtures are to be installed then mount in desired pattern andrun cord from additional through knockout provided to main fixture on outlet 5. Si plusieurs dispositifs doivent être installés , montez les selon le modéle désiré et faire passer les fils supplémentaires à travers la roulette d’expulsion fournie avec le dispositif principal. 6. Wire all fixtures together. Maximum 8 fixtures on one circuit. 6. Fixer tous les fils ensembles. Maximum 8 fils par circuit. These fixtures contain dimmable drivers and can be dimmed using any triac dimmer. We recommend Lutron CL series dimmers for maximum performance. Ces modèles contiennent des pilotes à intensité réglable, n’importe quel graduateur triac peut être utilisé. Nous recommandons la série Lutron CL pour un maximum d’efficacité.
The transformer for this light engine is not dimmable. Do not use a dimmer on this fixture or it will damage the transformer. Using a dimmer voids the warranty of ...
Wire all fixtures together. Maximum 8 fixtures on one circuit. 6. Fixer tous les fils ensembles. Maximum 8 fils par circuit. These fixtures contain dimmable drivers ...
visto por otros] y tuberÃa de drenaje) para desa- lojar el condensado. 3.Fije el ventilador al soporte de montaje mediante los tornillos de hojalata suministrados.
Blue. Green/Yellow. Blue. Black. Brown. L1. L2. 115 Volt single Phase fans. 230 Volt single Phase fans. CA. E. D dimensions and Wiring (Models FKD 12XL, 14, ...
5 nov. 2010 - Route the fixture wire to the low voltage trunk line. 1. Afloje el tornillo de bloqueo de cabeza hexagonal, gire la horquilla en la posición que se ...
READ THESE INSTRUCTIONS. & SAVE FOR FUTURE REFERENCE! Instructions pour l'installation modèle RVF. LIRE CES INSTRUCTIONS. ET CONCERVER POUR RÃFÃRENCE FUTURE! Instrucciones de instalacion modelo RVF. LEA ESTAS INSTRUCCIONES. Y GUARDE PARA REFERANCI
like a cutter knife, be careful not to damage the components ... Ensure that you have all required contents for complete ... CAUTION: Xenon bulbs get very hot.
Insert the large grease tray all the way under the back edge ..... I Si un conduit de raccordement flexible est utilisé, sa longueur ne doit pas dépasser 4 pi (121,9 ...
All safety messages will follow the safety alert symbol and either the word “DANGER” or ..... F. 6" (15.2 cm) min. clearance from both sides of range to side wall.
ventilation system may cause ignition and combustion problems with this gas ...... Power Spare. RD. WH. BK WH. RD. Reignition. Module. Cooktop. Front View.
any pressure testing of the gas supply piping system at test pressures equal to or ..... Use the following chart to find the exact orifice spud placement. Fully insert ...
that system at test pressures in excess of 1/2 psi (3.5 kPa). Line pressure .... continues until the flame is lit or the knob is turned to OFF. NOTE: The first time ...
These words mean: follow instructions. instructions. DANGER. WARNING. BUILT-IN ..... Connect the 2 yellow-green wires (B) together using a UL listed wire ...
by its side or rear flanges. □. The gas and electric supply should be located as shown in the “Gas and Electric Connection Locations” section so that they are ...
1/2" (13 mm) deep-well socket. 7 mm nut driver. Masking tape. IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking ...
•If you cannot reach your gas supplier, call the fire department. ... Flame spreader (on grill models). □ ...... Test the flame by turning the control from LO to HI,.
Operation of Cooktop Burners” section in the “Complete. Installation” section. 6. .... Remove spring retainer from the cap by pushing against the flat side of the ...
any pressure testing of the gas supply piping system at test pressures equal to .... continues until the flame is lit or the knob is turned to OFF. Check Operation of ...
