These factors must be supplied by the person(s) caring for and operating the fixture. Read all instructions. Do not install this fixture in hazardous locations. N'installez pas cet appareil dans des emplacements dangereux. Do not install any fixture assembly closer than 6 inches from any curtain or similar combustible material.
INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS MESURES DE SECURITE A RESPECTURE Before assembling your ACCESS LIGHTING fixture, please make sure that you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture configuration are made. Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille d'instructions et de s'y référer lorsque les ajouts ou changements dans la configuration de montage sont faites. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR. CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES CONDUCTEURS DE LA DERIVATION SONT ADEQUATS THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONTSTRUCTION
COLLECTION
APPLICATION
Archie
Wall Fixture
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
MODEL NO. 50177
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHERENTS
WHAT WE PROVIDE
WHAT YOU NEED
NOTE: The important safeguards and instructions that appear in this
•
Crossbar
•
Screwdriver
manual are not meant to cover all possible conditions and situations
•
Mounting Hardware
•
Wire Cutters
care, are factors that can’t be built into any product. These factors must
•
Mounting Plate
•
Wiring Supplies as Specified
be supplied by the person(s) caring for and operating the fixture.
•
Back Plate
Read all instructions
•
3 x Glass Shades
that may occur. It must be understood that common sense, caution and
Do not install this fixture in hazardous locations.
by Electrical Code
•
3 x 60W E26 Medium Base Bulb
N'installez pas cet appareil dans des emplacements dangereux. Do not install any fixture assembly closer than 6 inches from any curtain or similar combustible material. Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute surface combustible. "WARNING Risk of Fire and Electric Shock." “CAUTION: Risque d’ Incendie et de Choc Electriques.”
GENERAL INFORMATION
STEP BY STEP INSTRUCTIONS
All electrical connections must be in accordance with all ordinances,
Before starting your installation disconnect the Power by turning off the
Local and the U.S. National Electrical Codes (NEC). These fixtures are
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
intended for mounting to a standard 4” metal octagon outlet box.
light off at the light switch is not sufficient to prevent electrical shock.
The box must be directly supported by the building structure and U.L. Recognized.
1
CERTIFICATION: cULus DAMP
NO. 50177
1 2
MOUNT BACK PLATE If there is an existing fixture remove it. Expose the supply wires from the j-box. Mount the back plate to the j-box with the supplied screws.
CONNECT THE WIRES Gently pull the supply wires. Connect the black supply wire the black fixture wire. Secure with the supplied wire nuts. Connect the white supply wire to the white fixture wire. Secure with the supplied wire nuts. Attach the green J-Box wire around green hexagonal head screw or connect it to the green supply grounding wire of the fixture. Secure all wires with electrical tape (not supplied). Tuck all wires carefully into the J-Box.
3 2
MOUNT THE CANOPY Fit the fixture canopy over the back plate. Align the screw holes on the top and bottom of the canopy and the back plate. Insert the supplied screws, tighten down and secure.
CERTIFICATION: cULus DAMP
NO. 50177
4
INSERT THE BULBS
5
SECURE THE GLASS SHADES
6
RESTORE THE ELECTRICITY AND
Insert the bulbs. MAXIMUM WATTAGE 60W. DO NOT EXCEED THE MAXIMUM WATTAGE AS STATED ON THE WARNING LABEL AND INSTRUCTION SHEET.
Secure the glass shades to the fixture, by fitting the glass over the socket. Secure the glass by inserting the supplied screws through the designated hole in the glass and the metal post. Tighten down to secure
CHECK THE OPERATION OF YOUR NEW ACCESS LIGHTING FIXTURE
CAUTION
Please ensure that the fitting is cool and switched off before replacing the bulb. DO NOT use bulbs that might exceed the maximum wattage, stated on caution label.
Expose the supply wires from the outlet box. Hold the fixture back plate to the wall and mark with a pencil the location for the additional support. Remove and drill holes in the wall to accommodate the supplied hardware. WHAT WE PROVIDE. â¢. Back P
Before starting your installation disconnect the Power by turning off the. Circuit Breaker or by removing the fuse at the fuse box. Just turning the light off at the light switch is not sufficient to prevent electrical shock. ⢠1 x R7s Base Bulb. (
9 oct. 2011 - Install cover support collar [4] in the floor box opening with the top edge of the collar below the edge of the floor box using retained pan head screws. Tighten to 10 - 15 lbs-in torque [1.1 - 1.7 N·m]. Reinstall concrete cover [2] us
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE. INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONTSTRUCTION. AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ...
Insert the large grease tray all the way under the back edge ..... I Si un conduit de raccordement flexible est utilisé, sa longueur ne doit pas dépasser 4 pi (121,9 ...
All safety messages will follow the safety alert symbol and either the word “DANGER” or ..... F. 6" (15.2 cm) min. clearance from both sides of range to side wall.
ventilation system may cause ignition and combustion problems with this gas ...... Power Spare. RD. WH. BK WH. RD. Reignition. Module. Cooktop. Front View.
any pressure testing of the gas supply piping system at test pressures equal to or ..... Use the following chart to find the exact orifice spud placement. Fully insert ...
that system at test pressures in excess of 1/2 psi (3.5 kPa). Line pressure .... continues until the flame is lit or the knob is turned to OFF. NOTE: The first time ...
These words mean: follow instructions. instructions. DANGER. WARNING. BUILT-IN ..... Connect the 2 yellow-green wires (B) together using a UL listed wire ...
by its side or rear flanges. □. The gas and electric supply should be located as shown in the “Gas and Electric Connection Locations” section so that they are ...
1/2" (13 mm) deep-well socket. 7 mm nut driver. Masking tape. IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking ...
•If you cannot reach your gas supplier, call the fire department. ... Flame spreader (on grill models). □ ...... Test the flame by turning the control from LO to HI,.
Operation of Cooktop Burners” section in the “Complete. Installation” section. 6. .... Remove spring retainer from the cap by pushing against the flat side of the ...
any pressure testing of the gas supply piping system at test pressures equal to .... continues until the flame is lit or the knob is turned to OFF. Check Operation of ...
Outillage et pièces . .... If your washer includes a sound shield, please refer to the instructions included with the sound shield to install it at this time. NOTE: Keep ...
A time-delay fuse or circuit breaker is recommended. □. This range is equipped with a CSA International Certified. Power Cord intended to be plugged into a ...
I Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed. ..... Insert the small grease tray all the way under the front of the.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and ..... †®TEFLON is a registered trademark of Chemours.
Pour toutes cuisinières à gaz Thermador Professional® ... Do not use any phone in your building. .... installed on either side of the hood is 13". A ..... The gas supply connections shall be made by a ..... cuisinière, car ces types d'appareils.T
Failure to follow these instructions can result in death or serious burns to children and adults. Anti-Tip ..... I.D. flexible metal appliance connector may be used.
tableau de commande (Voir REMARQUE.) C. 353/4" (90,8 cm) de hauteur de table de cuisson lors de l'installation des roulettes. D. 30" (76,2 cm) de largeur.
(63.5 cm) countertop; front of oven door protrudes 3" (7.6 cm) beyond 24" (61.0 ..... screw for the left rear, right rear, center rear, and center front burner valves ...
Large flat-blade screwdriver ..... blade screwdriver, turning the regulator cap clockwise. 4. Test the ... Remove the burner base by first removing (2) Tâ20 screws.