INSTALLATION INSTRUCTIONS 709-LED Pendant PD-70913/PD-70925/PD-70937/PD-70945 CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING. Read all instructions before installing. System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations. When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only. Retain installation instructions for future maintenance reference. WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing. MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth. MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer. Lisez toutes les instructions avant l’installation. Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux règlements locaux. Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base. ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées. NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un chiffon humide.

HARDWARE

A

:LUH&RQQHFWRU 4W\SFV([WUD

dweLED.com Phone (800) 526.2588 Fax (800) 526.2585

Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050

B

0RXQWLQJ6FUHZ  4W\ ([WUD

Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122

Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760

dweLED retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Feb 2019

1

INSTALLATION INSTRUCTIONS 709-LED Pendant PD-70913/PD-70925/PD-70937/PD-70945 Junction Box

Fig.1

A

Mounting Back Plate Dimensions

:LUH&RQQHFWRU

Mounting Plate

1 3/4"

1 3/8"

Ø5 1/2" -XQFWLRQ%R[6FUHZ

 B0RXQWLQJ6FUHZ

Cable-gripper

Driver 3 6/8" x 3 6/8"W x 1/2"H Cable-gripper

Push up fi

Fig.3

Purple - Dim+

Fixture Black - Hot

Gray - Dim-

White - Neutral

Red - Fixture+ Black - Fixture-

PREPARATION 1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar. 2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation. CONNECTING THE WIRES (FIG. 2) 3. Remove the mounting screw (B) and back plate from the fixture. 4. Adjust the fixture wire length by pushing the cable-gripper on the canopy and pulling the wire as desired a. Retract the wire close to the desired length within the canopy before securing the fixture in place. NOTE: Using the cable-gripper to adjust more than 18" of wire length is not recommended. WARNING: Shortening the cable without professional help or electronic back ground is not advisable. Any modifications to the fixture will result in voiding the warranty of the product. 5. Secure the mounting back plate to the junction box using the screws provided with the junction box. NOTE: The side of the mounting plate marked "GND" must face out. 6. Connect the driver's input wires with junction box wires as shown (Fig. 2). Make sure that all wire connectors are secure. If your outlet box has a green or bare copper ground wire, connect the fixture's ground wire to it. Otherwise, connect the fixture's ground wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box. 7. Secure the fixture to the mounting back plate using the mounting screws (B). NOTE: This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming wiring information. DIMMING WIRING INSTRUCTIONS (FIG. 3) 9.

To utilize ELV or TRAIC dimming: use black (hot), white (neutral) and bare copper ground wires (ground).

10. To utilize 0-10V dimming: use purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wires (ground).

dweLED.com Phone (800) 526.2588 Fax (800) 526.2585

Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050

Fig.2 Wiring

Fixture Wires Black or Smooth

House Wires Black (Hot)

Fixture Wires White or Ribbed

House Wires White (Neutral)

Fixture Wires Bare wire (Ground)

House Wires Green or Bare Copper (Ground)

Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122

Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760

dweLED retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Feb 2019

2