This device may not cause harmful interference, and. 2. This device must accept any ... Contains FCC ID: I28RFID-CPMFS-02. This transmitter complies with ...
This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for Class B Digital Devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the product manuals, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to do one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced RF service technician for help.
The end product must be labeled, in a visible area, with the following: Contains FCC ID: I28RFID-CPMFS-02
Modification Warning The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with fully shielded communication cables.
RF Exposure Statement This transmitter complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter product procedures.
Canadian DOC Compliance Statement Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This Class B digital apparatus complies with Canadian ICES-003.
Industry Canada (IC) Warning Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) This device may not cause interference., 2) This device must accept any interference, including interference that may cause undesired operation of the device. The end product must be labeled, in a visible area, with the following: Contains IC: 3798B-CPMFS02
Approved Antenna information Only Zebra approved antennas are allowed and cannot be user replaceable. Antenna Type: PCB: Gain: -20 dBi
General The Contactless Encoder CPMFS02 radio module has been certified as a LMA. Additional evaluation is required for use in all host devices. The following describes the installation procedures for the various hosts in which the module has been evaluated.
Installation Instructions for Zebra printers The Contactless Encoder radio module is not intended for OEM Integrators or end users. It can only be installed at the grantee manufacturing facility.
light transmission. We provide ... more resolution at a lower cost than their absolute ... Absolute encoders are used in applica- ... determine if the encoder is turning clockwise ... two-channel quadrature input without further ... To measure distan
rating plate is located on the bottom of the control panel, at the far right, .... SIDE VIEW. *Without .... parte inferior del montaje del panel de control, en el extremo.
Los números de productos seguidos de ... without notice, as specified in the Price Book. ..... Debido a la naturaleza de las instalaciones bajo cubierta, Kohler.
... work or if your local electrical code requires professional installation! ..... Allineare i quattro fori per viti sul modulo ottico con i quattro fori del mozzo del ...
flujo en un sistema de ducha existente, verifique la compatibilidad antes de su ducha. No utilice este producto de bajo flujo Kohler con una válvula de ducha ...
Twist ends of stripped wires together as per schematic. ⢠Twist on wire connectors clockwise until secure. ⢠Connect green ground wire to bare wire, and mount to ...
or Bare Copper (Ground Wire) from outlet box. Twist wires together clockwise and secure with wire connector (E). Installer Tip (2): If ground wire is not available in outlet box, then secure Bare Copper (Ground Wire) from fixture to ground screw (F)
when the door is open or through the window of glass door models. GRILLE .... socket, turn the 3/8" hex bolt clockwise to raise the unit or counterclockwise to ...
The oven door must be open to view the rating plate. Refer to the illustration .... produzcan heridas graves o incluso la muerte si no se siguen las precauciones.
Cablofil, the inventor of wire mesh cable tray is a revolutionary cable management system that provides exceptional strength combined with the flexibility to adapt easily to field requirements. installation is easier since wire mesh requires fewer pa
O-ring over the faucet supply hoses and place into the groove in the underside of the faucet body (not shown). For all installations: Feed the faucet supply hoses ...
antenna of a different type or with a gain higher than 2.14 dBi is strictly ... every application using the MGM12P will need to perform the radio EMC tests on the ...
immediately, protect the end connector with tape or other shielding material. ... NOTICE: Do not pinch, nail, wedge, or use undue force when handling the silver crossover ... If additional equipment is to be connected downstream of this device,.
minimum of 69¹âµâââ" (177.6 cm) high, 22¹âââ" (56.0 cm) wide, and. 21â·ââ" (55.5 cm) ... is open air, allow a minimum of 7â·ââ" (20.0 cm) above the refrigerator.
Kohler Co. reserves the right to make revisions in the design of trip levers without notice, as specified within the Price Book. Adjustable. Wrench. 1017838-2-C. 2.
VONN highly recommends to use a qualified, licensed electrician to install the fixture. VONN recommends to install the fixture on its own independent circuit. Do not install the fixture on the same circuit with other appliances, or. HVAC systems. DO
6 On the Notification Service Plugin page, accept the default (1840) or enter a port for the plugin, and .... The BMC Impact Solutions Documentation is a .pdf of all manuals that support the .... mode of the installation program, in this case, silent
design des robinets et ceci sans préavis, comme spécifié dans le catalogue des prix. Clé à molette. Clé à sangle. Joint d'étanchéité pour filetage. Mastic de.
Distance between centerline to holes 12-13/16" (324.65 mm). Distance ... and the floor line with the floor of the cutout. Tape it into ... Floor Line of Cutout Opening.