1. INSTALL STABILIZER BAR Install the stabilizer bar, 2 bushings, brackets and 4 bolts. Torque: 19 N·m (190 kgf·cm, 14 ft·lbf) HINT: Install the bushings to the outside of the each paint line.
F08672
2. (a)
SST
(b)
INSTALL SUSPENSION MEMBER Using SST, align the holes of the suspension member and body. SST 09670-00010 Employ the same manner described above to the other side.
F08808
(c)
A A
B B
F08469
Install the suspension member with the 4 bolts. Torque: Bolt A: 70 N·m (715 kgf·cm, 52 ft·lbf) Bolt B: 116 N·m (1,185 kgf·cm, 86 ft·lbf) 3. Power steering: CONNECT TUBE CLAMP Connect the tube clamp with the bolt. Torque: 7.8 N·m (80 kgf·cm, 69 in.·lbf) 4. Power steering: CONNECT PRESSURE FEED AND RETURN TUBES (See page SR-61 ) 5. CONNECT SLIDING YOKE (See page SR-20 )
6. CONNECT ENGINE REAR MOUNT Connect the engine rear mount with the bolt and 2 nuts. Torque: 80 N·m (810 kgf·cm, 59 ft·lbf) 7. DISENGAGE ENGINE SLING DEVICE 8. INSTALL ENGINE HOOD (See page BO-6 )
Bolt
Nut F08675
2002 ECHO (RM884U)
Author:
Date:
999
SA-40 SUSPENSION AND AXLE
-
FRONT STABILIZER BAR
9.
CONNECT LOWER SUSPENSION ARMS TO STEERING KNUCKLES (a) Connect the lower suspension arm to the steering knuckle with the nut. Torque: 98 N·m (1,000 kgf·cm, 72 ft·lbf) (b) Install a new clip. If the holes for the clip are not aligned, tighten the nut further up to 60°. (c) Employ the same manner described above to the other side. 10. CONNECT TIE ROD ENDS TO STEERING KNUCKLES (a) Connect the tie rod end to the steering knuckle with the nut. Torque: 49 N·m (500 kgf·cm, 36 ft·lbf) (b) Install a new cotter pin. If the holes for the cotter pin are not aligned, tighten the nut further up to 60°. (c) Employ the same manner described above to the other side. 11. (a)
(b) 12.
INSTALL STABILIZER BAR LINKS Install the stabilizer bar link, 4 cushions and 5 retainers with the 2 nuts. Torque: 18 N·m (180 kgf·cm, 13 ft·lbf) Employ the same manner described above to the other side. INSTALL FRONT WHEELS Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
When installing the front seat outer belt, take care that the wiring does not interfere with other parts and is not pinched between other parts. 1. INSTALL FRONT ...
INSTALLATION. 1. INSTALL ELECTRIC COOLING FAN TO RADIATOR. Install the cooling fan with the 3 bolts. Torque: 7.5 N·m (80 kgf·cm, 66 in.·lbf). 2. INSTALL ...
(a) Install the floor shift assembly with the 4 bolts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf). (b) Install the wire harness clamps to the shift lever plate. (c) Shift the shift ...
INSTALLATION. 1. INSTALL STARTER. (a) Install the 2 bolts and starter. (b) Connect the starter wire, and install the nut. (c) Connect the starter connector. 2.
(b) Install the coil spring to the shock absorber. HINT: Fit the lower end of the coil spring into the gap of the spring low- er seat. (c) Install the upper insulator with ...
(a) Fasten the front seat belts. (b) Drive the car at 10 mph (16 km/h) and slam on the brakes. Check that the belt locks and cannot be extended at this time. HINT:.
NOTICE: Be careful not to damage the serrations. (c) Install the spacer. (d) Coat a new oil seal lip with molybdenum disulfide lithium base grease. (e) Using SST ...
75.000 - 75.013 mm (2.95275 - 2.95326 in.) Maximum diameter: 75.013 mm (2.95326 in.) If the diameter is greater than maximum, replace the cylinder block. 6.
(a) Remove the door inside handle in order A, B as shown in the illustration. (b) Disconnect the door lock cable from the door inside han- dle. 8. REMOVE PULL ...
INSTALL NEW O-RINGS AND TANKS. (a) After checking that there are no foreign objects in the lock plate groove, install the new O-ring without twisting it. HINT:.
Try to rotate the clutch pinion gear counter- clockwise and check that it locks. If necessary, replace the starter clutch. 13. INSPECT MAGNETIC SWITCH.
Conditions (a), (b) and (c) continue 10 sec. or more with engine speed 900 rpm or less: (2 trip detection logic). (a) Throttle valve fully closed. (b) Mass air flow ...
Alarming time. 60 seconds. Alarming output. Continuous 0.4 secs.: (ON). 0.4 secs.: (OFF). HINT: In the arming condition when either of doors is unlocked with.