Installation and Wiring Manual Manuel pour l ... - Amre Supply
United States 10048 Industrial Blvd. ⢠Lenexa, KS 66215 ⢠1.800.747.1762 ⢠www.fantech.net. Canada 50 Kanalfiakt Way ⢠Bouctouche, NB E4S 3M5 ⢠1.800.565.3548 ⢠www.fantech.net. Fantech, reserves the right to modify, at any time and without notice, any or all of its products' features, designs, components and.
Installation and Wiring Manual Manuel pour l'Installation et le Câblage
Item #: 401285 Rev Date: 2015-05-12
RTS2
Ventilation Control System – 20 minute timer Système de contrôle de ventilation – minuterie de 20 minutes Product # / n° du produit: 40164 Operation modes of the RTS2 The Fantech RTS2 is compatible with Fantech SHR, VHR and SER series models. This button activates the system on high speed ventilation mode for 20 minutes, it then returns to the predetermined setting. To cancel this operation, simply press the button a second time.
Modes de fonctionnement du RTS2
Push
Le RTS2 de Fantech est compatible avec les séries SHR, VHR et SER de Fantech. Cette minuterie démarre le système en mode de ventilation en vitesse maximale pendant 20 minutes. Il retourne ensuite au réglage choisi. L’opération peut être annulée en poussant le bouton une deuxième fois.
Wiring of the RTS2 Insert the stripped end of the wire into the terminal connection on the HRV or ERV marked T+ and T– or TIMER+ and TIMER –, near the power cord. Using a pen-type screwdriver, tighten the screws. Run the wires to the RTS2. With the polarity respected, insert the stripped end of the wires into the electrical connections marked “+“ and “ – “ . Using a pen-type screwdriver, tighten the screws. Up to 5 timers can be installed in parallel.
Câblage du RTS2 Insérer les raccords femelles dans les raccords T+ et T– ou TIMER+ et TIMER –, situés près de la prise de courant du VRC ou VRE. Déplacer le fil jusqu’au RTS2. En respectant la polarité, inserer les bouts de fils dénudés dans les raccords "+" et "-". Serrer les vis à l’aide d’un tournevis mince. Jusqu'à 5 minuteries peuvent être installés en parallèle.
RTS2
or/ou
+T –T
Installation of the RTS2 Screw the control mounting plate to the box then screw the cover over the mounting plate.
Installation du RTS2 Visser la plaque de montage à la boite électrique puis visser le couvert à la plaque de montage.
United States 10048 Industrial Blvd. • Lenexa, KS 66215 • 1.800.747.1762 • www.fantech.net Canada 50 Kanalflakt Way • Bouctouche, NB E4S 3M5 • 1.800.565.3548 • www.fantech.net Fantech, reserves the right to modify, at any time and without notice, any or all of its products’ features, designs, components and specifications to maintain their technological leadership position. Fantech se réserve le droit de modifier partiellement ou entièrement, en tout temps et sans préavis, les caractéristiques, la conception, les composantes et les spécifications de ces produits afin de conserver sa position de leader en matière de technologie.
4 janv. 2013 - jonction en utilisant la visserie fournie ou des vis tire-fond. Utilisez n'importe quelle combinaison de boîtes de jonction pour un montage.
4 mai 2013 - ... a problem not covered sufficiently for user's purpose, please contact ..... CECI CRÉERA UN JOINT IMPERMÉABLE ENTRE LA SURFACE DE ... mastic d'étanchéité ou du ruban Téflon (non fournis) sur le raccord ... REMARQUE: Les spécifications
Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after installation. Filter Bypass Plug. You must use ...
American Society for Heating, Refrigeration, and Air Conditioning. Engineers (ASHRAE), and the local code authorities. c) When cutting or drilling into wall or ...
The depth of the pit should be at least 12” above the surface .... The manufacturer assumes no responsibility for damage or injury due to disassembly in the field.
7000 Apple Tree Avenue ..... Liberty Pumps, Inc. warrants that pumps of its manufacture are free from all ... Liberty Pumps, Inc. shall not be liable for any loss,.
... pit making sure the switch has adequate clearance and will not hang-up on the pit wall. ... For added protection, consider the addition of a back-up pump such as .... Electrical Service and Operation. DON'T! Fig. 1 Piggyback plug installation.
If your original motor had the pluggable motor switch (See Figures 2B and 2C), replace .... Switch connection #6 is the centrifugal switch normally open contact. 4. Switch connections #1 and #2 are the normally open heater contacts. 5. Switch ...
P1951M. 400. 260. II. PM390. 390. 260. I. PM500. 500. 290. I. RM51000. 370. 260. I. RM52000. 370. 260. I. RM53000. 370. 260. I. RM65000. 450. 275. II. RMP1.
The electrical connections and wiring for a pump installation should only be made by qualified personnel. ... thinner or other chemicals down drains, as they can chemically attack and ..... the gate valve to prevent the back flow of liquid or gas.
and performance. Note: 25AUB-Z3 or LF25AUB-Z3 valves are suitable for accessible outdoor or pit installations. Installation Instructions. Series 25AUB-Z3.
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not ...
partir de la fecha de embarque original, que sus productos están libres de defectos en materiales y mano de obra ... Algunos Estados no permiten limitaciones en la duración de una garantÃa implÃcita y algunos Estados no permiten la exclusión o l
7/16. (11). 1-1/2. (38). 1/4 (6) DIA. 3 (76). M18353. Fig. 3. LP914A wall model mounting bracket. ... Use the template provided and drill a large center hole.
COVER FASTENER. BEFORE INSTALLATION. This normally-open, single-seated, straight-through, pneumatic valve provides two-position or proportional control .... 35 Dynamic Drive. Golden Valley, MN 55422. Scarborough, Ontario. M1V 4Z9. 95-5544EFâ1 B.B.
Limited Warranty: Watts Regulator Co. (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a ...
qroduct to make sure the product is suitable for your ?pplication. 3. Installer must be a trained, experienced service technician. 4. After installation is complete, ...
The wire colored brown must be connected to the terminal which is marked with the letter L or ..... removes algae and slime. Step 1 Remove the front door to ...