1. INSPECT INJECTOR INSPECTION CAUTION: Keep injector clear of sparks during the test.
SST (Clamp) Fuel Pipe (On vehicle)
Injector
B00066
(a) Fuel Tube Connector
Purchase the new fuel tube and take out the fuel tube connector from its pipe. Part No. 23901-22010
S05359
(b)
Connect SST (hose) and fuel tube connector to the fuel pipe. SST 09268-41047 CAUTION: Perform connecting operations of the fuel tube connector (quick type) after observing the precautions.
SST (Hose) Fuel Tube Connector Fuel Pipe B00067
SST (Hose)
(c) (d)
SST (Union) O-Ring SST (Clamp) Vinyl Tube
Install the grommet and O-ring to the injector. Connect SST (union and hose) to the injector, and hold the injector to prevent gasoline from splashing out. SST 09268-41047 Put the injector into a graduated cylinder.
(e) HINT: Install a suitable vinyl tube onto the injector to prevent gasoline from splashing out.
B00068
TOYOTA Hand-Held Tester
DLC3
D08002
(f) (g)
Connect the TOYOTA hand-held tester to the DLC3. Turn the ignition switch ON and TOYOTA hand-held tester main switch ON. NOTICE: Do not start the engine. (h) Select the active test mode on the TOYOTA hand-held tester. (i) Please refer to the TOYOTA hand-held tester operator’s manual for further details.
2002 ECHO (RM884U)
Author:
Date:
731
SF-22 SFI
(j)
-
INJECTOR
If you have no TOYOTA hand-held tester, connect the positive (+) and negative (-) leads from the battery to the fuel pump connector. (See page SF-18 )
(k)
SST (Wire)
Battery
B00416
Connect SST (wire) to the injector and battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times. SST 09842-30080 Volume: 47 - 58 cm3 (2.7 - 3.3 cu in.) per 15 sec. Difference between each injector: 10 cm3 (0.6 cu in.) or less If the injection volume is not as specified, replace the injector. 2. (a)
B00069
INSPECT LEAKAGE In the condition above, disconnect the test probes of SST (wire) from the battery and check the fuel leakage from the injector. SST 09842-30080 Fuel drop: 1 drop or less per 12 minutes (b) Turn the ignition switch to LOCK. (c) Disconnect the negative (-) terminal cable from the battery. (d) Remove the SST and fuel tube connector. SST 09268-41047 CAUTION: Perform disconnecting operations of the fuel tube connector (quick type) after observing the precautions. As there is retained pressure in the fuel pipe line, prevent it from splashing inside the engine compartment. (e) Disconnect the TOYOTA hand- held tester from the DLC3.
Try to rotate the clutch pinion gear counter- clockwise and check that it locks. If necessary, replace the starter clutch. 13. INSPECT MAGNETIC SWITCH.
75.000 - 75.013 mm (2.95275 - 2.95326 in.) Maximum diameter: 75.013 mm (2.95326 in.) If the diameter is greater than maximum, replace the cylinder block. 6.
(a) Fasten the front seat belts. (b) Drive the car at 10 mph (16 km/h) and slam on the brakes. Check that the belt locks and cannot be extended at this time. HINT:.
CIRCUIT DESCRIPTION. The vehicle speed sensor outputs a 4-pulse signal for every revolution of the transaxle output shaft. After this signal is converted into a ...
When all the component parts, wire harnesses and con- nectors of each circuit except the ECU are found to be normal in troubleshooting, then it is determined ...
AC Form 8050-2, Aircraft Bill of. Sale (kit aircraft only) ... Purchase a logbook for the air- frame, engine, and ... FAA Order 8130.2, "Airworthiness. Certification of ...
Other types include hinged doors in ply-covered structures or .... George C. Prill, Director of the FAA's Flight Stan- dards Service, said the data is needed to evaluate and plan the maintenance airman certification and surveillance pro- gram.
fumes are poisonous and can cause loss of consciousness and death in a short time. Never drain the float bowl when the engine is hot. Severe burns may result.
(b) Install the coil spring to the shock absorber. HINT: Fit the lower end of the coil spring into the gap of the spring low- er seat. (c) Install the upper insulator with ...
When installing the front seat outer belt, take care that the wiring does not interfere with other parts and is not pinched between other parts. 1. INSTALL FRONT ...
INSTALLATION. 1. INSTALL ELECTRIC COOLING FAN TO RADIATOR. Install the cooling fan with the 3 bolts. Torque: 7.5 N·m (80 kgf·cm, 66 in.·lbf). 2. INSTALL ...
NOTICE: Be careful not to damage the serrations. (c) Install the spacer. (d) Coat a new oil seal lip with molybdenum disulfide lithium base grease. (e) Using SST ...
