Dec 4, 2014 - 8. PIN. 9. 9. PIN. 10. 10. PIN. 11. 11. PIN 12. 12. PIN 13. 13. PIN 14. 14 ... PIN 69. 69. PIN 70. 70. PIN 71. 71. PIN 72. 72. PIN 73. 73. PIN 74. 74.

Mar 3, 2014 - PIN 26. 26. PIN 27. 27. PIN 28. 28. PIN 29. 29. PIN 32. 32. PIN 30. 30. PIN 31. 31. PIN 33. 33. PIN 34. 34. PIN 35. 35. PIN 36. 36. PIN 37. 37.

140. Title. ADP-A TF1504/8 for HiLO ALLxx. Size. Number. Revision. Date: File: 4/9/2014. C:\HiLo\ADP-ATF1508. SchDoc. SchDoc. Sheet of. Drawn By: Sheet.

Feb 26, 2018 - PIN 26. 26. PIN 27. 27. PIN 28. 28. PIN 29. 29. PIN 32. 32. PIN 30. 30. PIN 31. 31. PIN 33. 33. PIN 34. 34. PIN 35. 35. PIN 36. 36. PIN 37. 37.

Aug 4, 2014 - PIN 26. 26. PIN 27. 27. PIN 28. 28. PIN 29. 29. PIN 32. 32. PIN 30. 30. PIN 31. 31. PIN 33. 33. PIN 34. 34. PIN 35. 35. PIN 36. 36. PIN 37. 37.

Revision. Size. B. Date: 3/3/2014. Sheet of. File: C:\HiLo\ADP-CY37xxx.SchDoc. Drawn By: ADC-CY37xxx for HiLo ALLxx tinhead@eevblog. PIN 1. 1. PIN 2. 2.

A N E O O 2o N o. Title. * A. ADP-ATF1500 for HiLo ALLxx. VPP. Size. Number. Revision. Date: File: 4/8/2014. C:AHÄ°Lo\ADP-ATF1500.SchDoc. Sheet of.

Title. ADP-A TF1502/4 for HiLO ALLxx. Size. Number. Revision. Date: File: 4/9/2014. C:\HiLo\ADP-ATF1504.SchDoc. Sheet of. Drawn By: tinhead@eevblog.

Title. ADP-PZ5000 for HiLo ALLXX. Size. Number. Revision. Date: File: 4/12/2014. C:\HiLo\ADP-PZ5000.SchDoc. Sheet of. Drawn By: tinhead@eevblog. 6.

Empty Test. Pre-program Bit Test ... Section 6. 6.1. 6.2. Interface. Setting the Interface Parameters. Input/Output Operation. (Revision .... 272512..ace.. ZF0D..11.

PROGRAM. The was to ... Memory Device Programming. Sections 28 ... previously selected device to be reinstated and the main systern ment were revision ...

2. Which Devices Are Supported? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Online Device List . ... Bulletin Board Service (BBS) . .... 24. LabSite User Manual iii ...

4 or 8 pieces at a time in DIP or PLCC packaging in PC-based or stand-alone modes. Using the latest in pin driver technology 4 or 8 pieces of 27CO10 devices ...

change current serial port settings, or to quit the application. If communication ... status area, the menu bar, the toolbar, the response window and the status bar.

This manual provides the instructions for using the ChipWriter Gang ...... For technical assistance, repair or warranty service, contact your local Data I/O ... Online help files provide more information about the BBS and its capabilities. Before you

March 2001 - PC Based Programmer Manual Ver.3.0 ...... Both device programming algorithms and system operating software for this ...... for security purposes, or because the on-chip security features have been enabled when programming. .... program c

Apr 1, 2003 - and other Hitachi brand names are mentioned in the document, these ... logo and corporate statement, no changes whatsoever have been ...

ProLinea is a trademark of Compaq Computer Corporation. Microsoft ..... o Setup password prevents unauthorized changes to the system configuration. Chapter ...

These are also used when calculating the check sum and CBC, and can be .... If the charge level ... Invert unit and place face down on clean, smooth sun'ace.

Fast programming algorithme were introduced almost imediately with switched ... The introduction of the 27256 necessatated the addition of the 12 5v Vpp .... "System Mode"); * switch programmer off, hold down the two oursor/arrow keys.

Depress the AC power pushbutton at the left rear of the programmer. This is .... point of the error, an error code is displayed, and the ..... ADDRESS amor .. RAM.

A block need not be defined to use the block editing functions (INVERT, SHIFT, ..... Calculate the checksum of the complete PROM or a specified RAM block. ..... the input handshake lines CTS and DSR, (pins 5 & 6) must taken to a high level (>.

List of Devices and Device Codes. 3.3 ... Error Reporting on Input/Output. Section. 12 .... The mainframe software revision can now be ascertained prior to the.

ST62,63 Programming Manual. 2/43 ... into a deep LIFO stacking area. On the return from .... The op- code specifies the bit to be tested, the byte follow-.