IMPORTANT SAFETY INSTRUCTIONS MESURES DE SECURITE A RESPECTURE Before assembling your ACCESS LIGHTING fixture, please make sure that you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture configuration are made. Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille d'instructions et de s'y référer lorsque les ajouts ou changements dans la configuration de montage sont faites. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR. CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES CONDUCTEURS DE LA DERIVATION SONT ADEQUATS THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONTSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
COLLECTION
APPLICATION
MODEL NO.
NAUTICUS
Wall or Ceiling
20292LEDDLP
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this manual are not meant to cover all possible conditions and situations that
WHAT WE PROVIDE
WHAT YOU NEED
may occur. It must be understood that common sense, caution and care,
• Crossbar
• Screwdriver
• Mounting Hardware
• Wire Cutters
• Canopy with Socket
• Wiring Supplies as Specified
are factors that can’t be built into any product. These factors must be supplied by the person(s) caring for and operating the fixture. Read all instructions
• 1 x Glass Shade and
Do not install this fixture in hazardous locations.
by Electrical Code
decorative guard
N'installez pas cet appareil dans des emplacements dangereux.
• 1 x A19 E-26 LED
Do not install any fixture assembly closer than 6 inches from any
bulb
curtain or similar combustible material. Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute surface combustible. "WARNING Risk of Fire and Electric Shock." “CAUTION: Risque d’ Incendie et de Choc Electriques.”
GENERAL INFORMATION
STEP BY STEP INSTRUCTIONS
All electrical connections must be in accordance with all ordinances,
Before starting your installation disconnect the Power by turning off the
Local and the U.S. National Electrical Codes (NEC). These fixtures are
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
intended for mounting to a standard 4” metal octagon outlet box.
light off at the light switch is not sufficient to prevent electrical shock.
The box must be directly supported by the building structure and U.L. Recognized.
1
NO. 20292LEDDLP
CERTIFICATION: cULus WET
1
PREPARE FIXTURE If there is an existing fixture remove it. Expose the supply wires from the outlet box. Secure the crossbar to the J-box with the supplied screws. Ensure that the additional screws face downward.
CONNECT THE WIRES
2
Gently pull the supply wires. Connect the black supply wire to the black fixture wire. Secure with the supplied wire nuts. Connect the white supply wire to the white fixture wire. Secure with the supplied wire nuts. Attach the green J-Box wire around green hexagonal head screw or connect it to the green supply grounding wire of the fixture. Secure all wires with U.L. Certified electrical tape (not supplied). Tuck all wires carefully into the J-Box.
3 2
MOUNT THE CANOPY Fit the fixture canopy up to the crossbar. Insert the hanging screws into the designated holes in the canopy. Secure with the supplied thumb screws.
NO. 20292LEDDLP
CERTIFICATION: cULus WET
4 5
INSERT THE BULB Insert the supplied bulb.
DO NOT EXCEED THE MAXIMUM WATTAGE AS STATED ON THE WARNING LABEL.
SECURE THE GLASS SHADE Hold the glass shade and the decorative guard up to the canopy and secure with the supplied screws.
*This fixture is wet location rated. In order to ensure that moisture does not enter the outlet box and cause a short circuit, clear caulking should be used to seal the space between the fixture mounting bracket and the wall. Ensure that a space is left at the bottom to allow the escape of moisture. It is recommended that Indoor/Outdoor Silicon Sealant be used for this purpose**
6
RESTORE THE ELECTRICITY AND CHECK THE OPERATION OF YOUR NEW ACCESS LIGHTING FIXTURE
CAUTION
Please ensure that the fitting is cool and switched off before replacing the bulb. DO NOT use bulbs that might exceed the maximumwattage,statedon cautionlabel.
3 Dimmable fixture - see attached list for compatible dimmer switches.
Example: there is a web-design team in your organisation with 8 people. ... g) X:\imagex /compress maximum /capture d: y:\Windows7.wim âWindows 7 installâ.
May 14, 2003 - Before we start securing Apache, we must specify what functionality ... The server must not offer any network services except HTTP: (80/TCP); .... A different method must be used to create a /chroot/httpd/dev/log device, which is also
spring, they mix it into their soil, test to see what amendments, if any, are needed, and the ...... bodies about one-eighth of an inch long. The larvae live in the soil.
Apr 13, 1999 - Getting Samba . .... It is meant to help you get Samba up and running quickly, promise that you will read all the .... hide dot files = No. [public].
In this lab you will load new configuration files into your pod devices; these files ... your pod number for x and the router number for y in all instructions and ...... configuration you will also see more detail in the crypto pki certificate sectio
relational databases (NoSQL such as MongoDB, Cassandra), R data files, etc. ... Intelligence, Big Data and Analytics technologies such as Hadoop, NoSQL ...
Creating an ADO Query into Active Directory Step-by-Step Exercises . . . . . . . . . . ..... the vast majority of the cases, the solution is a simple VBScript. In Microsoft ...... notice that the query looks exactly like a regular SQL Server query. T
Move / black mark on the inner bar .... Si ocurrió algún daño durante el envÃo, devuelva la unidad completa al lugar de compra para su devolución o reposición.
edge to panel edge. Suggest to keep the distance of 5mm from metal edge to panel edge. Move the black mark to the center position, then tighten the screw “G”.
Remove all wrapping materials, including staples and packaging straps before you start to assemble. ⢠Do not tighten all screws/bolts until pieces are completely assembled. ⢠Keep all hardware parts out of children's reach. ⢠It is recommended
Mar 31, 2018 - Like all the switches we see in this series, this is a two-motion switch. It can make contact ... shaft in steps to the appropriate terminal on that level. At the bottom ..... 6-7-8, but as a contact would be numbered 3, identified by
Mar 31, 2018 - was of course served by a manual telephone switching system. .... 7 Attributed to Alexander E. Keith of the Strowger Company and his two frequent ...... distributing frame (MDF) and the intermediate distributing frame (IDF).
High Table Side Leg Frame 16209. Adjustable .... Coloque todas las partes laminadas sobre una superficie limpia y uniforme (como un tapete o la alfombra).
Jun 20, 2018 - this one) describe in detail (including at the circuit level) the different .... rods (with the nuts seen there). Figure 2. 200-point line finder bank ...
the system but it is also descriptive of the manner in which a call ... control system, on the other hand, interposes a circuit between ..... prevents switches from "plunging in" during ~the time it is ...... fraction of the trunks. ... out trunk is
This trim kit is for use with Quattro Diverter rough. 15930181, Trio Stop Diverter rough 15981181, or Trio Diverter 15984181. The rough valve must be installed, ...