Automatic. Standard ready (output). Disk change. A1 to A2. External. (InputâDensity). Hiâ2M. Lowâ1M. None. A1 to A2, E1 to F1. External. Hiâ2M. Lowâ1M.
Disk change (output) Standard ready (output) Disk change (output)
None
A1 to A2, E3 to F3, E1 to F1 A1 to A2, E3 to F3 A1 to A2, E3 to F3, E1 to E2 A1 to A2, E3 to F3, F1 to F2 A1 to A2, E3 to F3, E2 to F2 A1 to A2, E3 to F3, E1 to E2, F1 to F2
Automatic Automatic
None Standard ready (continued on next page)
3
Table 2 (Cont.) Jumper Descriptions for Mitsubishi Drive Jumpers
Disk change None Disk change Standard ready None Disk change Standard ready
Installing the Drive
To install your drive, perform the following steps: 1. Set the correct drive jumper settings. See the previous sections for configuration information. 2. Turn off your computer and disconnect the power cord. 3. Remove the computer cover and locate the drive bay. See the computer user information for instructions. Note
Depending on the layout of your computer, you may find it easier to connect the cables (step 4) before you mount the drive in the bay. 4. Mount the drive in a drive bay. See the computer user information for drive mounting instructions.
LED on: DRIVE SELECT *Ready. | Disable for auto-chucking. Enable for auto-recalibration. Short between FDD frame and DC OV. D$13. DS2. Strap post layout.
1.3 HA: Automatic density setting by HD Hole. 12. Other function setting ... HD OUT Automatic from FDD by ... *HI2 | Density set by HD IN on pin 2. *H02 HD OUT ...
DSO and D$1 Straps. (1) In the multiplex control, these straps designate the address of the FDD. (2) By the combination with the DRIVE SELECT O and I signals, ...
This manual has been provided for the use of authorized Yamaha Retailers and their service ... DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC ..... [ 140b]: Bind Head Tapping Screw-P 4.0X12 ZMC2Y (EP640110).
High Reliability Floppy Disk Drives by the employment of a direct-drive motor. ... 686 m/s2. ï¼70 Gï¼11ms half sine. W/R. Standby. Error rate. MTBF. MTTR. Soft.
101 (Disk ejected). 51 more. 9020.3. 6010.3. 10-13 tapped holes for. (Bottom x4, each side x3) installation then. E' OF08 we. - are are more some non are sono.
This manual has been provided for the use of authorized Yamaha Retailers and their service ... may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black .... 16 CELESTA 20 DRAWIA ORG 3 AASWC GTR 57 PICK BASA 71 SITA
Density set automatically. Density set by HD IN on pin 2. HD OUT output on pin 2. LED on: DRIVE SELECT * Ready. Disable for auto-chucking. Enable for auto- ...
teen. 91 - EN en. E-BN 0-. N en Car W. WNI BI-ER APEM Ces votos. L-ar ca ..... 7438. TLO82 (1/2)-2 wlo 10-or. Wo116 -on wions. WIATI -an. WIDTCT-ori C-ON.
Check that replaced wires do not contact sharp edged ..... Since the parts shown in Parts List of Preliminary Service Manual may have been the ... El-324536.
Reliability Specifications. ..... MTBF. Mean Time Between Failures. MTTR. Mean Time to Repair. PCB. Printed Circuit Board. PM. Preventive Maintenance. P-P.
be less than 0.5 mA rms AC. The resistance .... SP (Service Parts) Classification ... FUSE ICP.N1S SOV 0.6A. FUSE. ICP.N25 SOV 1.0A. FUSE SETT 250V 1.00A.
Floppy drive technology has continued to march on since this article was written in ... single-sided drive that came with most Mirage models with a more standard double- ... reversible) will likely void any warranty you have on your instrument. ... t