Put the glass shade (G) over the socket (I) and secure it with ring (F) and socket ring (E). 7. Install the light bulb in accordance with fixture's specifications.
INSTALLATION INSTRUCTION FOR FIXTURE 3722-PL READ AND SAVE THESE INSTRUCTIONS WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER . AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR. MOUNTING THE FIXTURE
1. Shut off the power supply at the fuse box or circuit Wiring (See fig.2) 1. Connect the electrical wires as follows. Connect the breaker box(avertissement! couper le courant au black wire from the fixture to the black (HOT) house niveau des fusibles ou du disjoncteur).Remove the old wire. Connect the white wire from the fixture to the fixture from wall. Including the old cross bar. white (Neutral) house wire. Make sure all the wire 2. Carefully unpack your new fixture and lay out all the nuts were secured. You may wrap the connections parts in a clear area. Take care not to lose any small with electrical tape. If your outlet box has a ground parts necessary for installation. wire (Green or Bare Copper) connect fixture’s 3. Attach the mounting plate (A) to the outlet box using ground wire to it. Other wise attach the bare copper the outlet box screws (B). The side of the mounting fixture wire to the green ground screw on the plate (A) marked “GND” must face out. mounting plate. 4. Follow the wiring instructions carefully (See Fig.2). 2. Tuck the wire connections neatly into the wall 5. Attach the fixture back plate (D) over the mounting junction box. plate (A) well, and secure with 2 steel screws (C) what are locked by the screw tool (H). 6. Put the glass shade (G) over the socket (I) and secure Fig.2 it with ring (F) and socket ring (E). 7. Install the light bulb in accordance with fixture’s specifications. DO NOT EXCEED THE MAXMUM WATTAGE RATING(ne pas depasser la puissance nominale maximale!)! The color correlated Temperature (CCT) for replacing the enclosed lamp is (2700K). 8. This fixture is rated for a minimum start temperature of -17° Celsius. 9. The ballast and lamp are combined, to replace or install, twist pins into socket as shown on Fig.3. Your installation is now complete. Return power to the junction box and test the fixture.
Fig. 1
Fig.3 BULB(INCLUDED) SOCKET RING(E)
SOCKET(I)
Contains Mercury (Hg) Dispose of according to Local, State and Federal Law. (www.epa.gov/bulbrecycling)
Step 3: Screw from underside of cabinet into block of wood (see fig. 1). Screws not provided. Paso 3: Introduzca un tornillo desde la parte inferior del armario al ...
bolt (I) of latch enters the strike hole. Reposition strike plate if required. Install strike plate (G). Minor loose door fit may be reduced by adjusting tang (H).
common nail, from inside. 2-1/8" (54mm) hole, through pilot hole until nail makes indentation in door jamb (E). 6. Drill 1" (25mm) diameter hole in door jamb (E).
that the slant of latch bolt faces in the direction that the ... see figure 5 and proceed with the following: (1) With ... For product with a lever with hidden screws, see.
courbe de la tige demi- ronde devrait correspondre ...... lame de torsion plus courte, 4) remplacer par la lame de torsion plus longue, 5) remettre le clip en place.
hole until nail makes indentation in door jamb (E). 6. Drill 1" (25mm) diameter hole in door jamb (E). Drill hole 5/8" (16mm) deep. 7. For latch with face plate (F),.
The sport of sailing carries a risk of personal injury. Spinlock accept no liability whatsoever for any .... ( pas de cable, ni de corde). ⢠Ne pas utiliser de bloqueur ...
courbe de la tige demi- ronde devrait correspon- dre à l'ouverture de votre ..... lame de torsion plus longue,. 5) remettre le clip en place. Utiliser les vis longues.
Similar situations exist for the roughly 40 isotopes currently in use ..... reactor with an integrated heat exchanger, according to an embodiment of the ...... counter, and for select samples, beta activity was measured with a liquid scintillator.
Footbridge for crack's inspection control method (Hamel and Mahony, 2000; Shell and Dickmanns, 1994). A typical vision system will include an off-the-shelf ...
Selecting the recirculation settings. Only to be used after the appliance is installed in a recirculation application. Sélection des paramètres de recirculation.
