fcc warning professional installation instruction - FCC ID
18 juil. 2016 - may lead to the violation of FCC/IC limit and is prohibited. Installation procedure. Please refer to user's manual for the detail. w Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could ...
Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 40cm between the radiator & your body.
Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 40 cm de distance entre la source de rayonnement et votre corps.
14203 Minuteman Drive, Suite 201 Draper, UT 84020-7211 1-801-822-5450
FCC WARNING PROFESSIONAL INSTALLATION INSTRUCTION XWO-BAP1 High Power AC1200 Dual-Band Outdoor Bridging AP Last Update: 07/18/16
Professional installation instruction Installation personal
Instructions d’installation professionnelle
This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting.
Installation
Installation location The product shall be installed at a location where the radiating antenna can be kept 40cm from nearby person in normal operation condition to meet regulatory RF exposure requirement.
External antenna Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/IC limit and is prohibited.
Installation procedure Please refer to user’s manual for the detail.
ww Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. To professional installer: 5.15-5.25G band (UNII band 1) is certified to indoor use only. Installer must disable UNII band 1 by provided proprietary tool when you install this device for outdoor application to comply with FCC requirement.
Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie maitrisant les radiofrequences et les regles s’y rapportant. L’installation et les reglages ne doivent pas etre modifies par l’utilisateur final.
Emplacement d’installation En usage normal, afin de respecter les exigences reglementaires concernant l’exposition aux radiofrequences, ce produit doit etre installe de facon a respecter une distance de 40 cm entre l’antenne emettrice et les personnes.
Antenn externe. Utiliser uniiquement les antennes approuvees par le fabricant. L’utilisation d’autres antennes peut conduire a un niveau de rayonnement essentiel ou non essentiel depassant les niveaux limites definis par FCC/IC, ce qui est interdit.
Procedure d’installation Consulter le manuel d’utilisation.
Avertissement Choisir avec soin la position d’installation et s’assurer que la puissance de sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales.
Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting ...
The power door locks will cycle when you have successfully entered ... If programming has failed, repeat this procedure from the beginning. ... Changes or modifications not expressly approved by Dorman Products Inc. could void the user's ...
Programming Instructions: 1) Turn vehicle ignition key to ON position, without starting engine (Key-On Engine-Off - Position "1"). 2) Insert Programmer into OBD connector DLC port ( - located under steering column, near pedals). Green LED should turn
Make sure the power door locks to confirm you are in the programming mode. 7) Press the LOCK ... button to confirm that the system has accepted the remote.
device, however, is less that the electromagnetic energy emitted by other wireless devices such as mobile phones. The headset operates within the guidelines ...
Do not attempt to charge your headset with anything other than the AC adapter provided. The use of any other types may ... Important: Please refer to the user manual for a description of the charging status indicator lights. Some headsets ..... carga
BATTERY INSTALL : (Fig.D&E)Locate and remove the locking screw on the battery door on the back of the controller with a phillipshead screw driver. Open the cover of battery case, insert 3 AAA batteries in correct polarity. Close the battery cover and
product, as this may cause short circuits which could result in a fire or electric shock. ⢠None of the ... dealers or service centers may open the product. If any parts ...
About the manuals. 1. Instruction Manual (this manual). 2. (Startup Guide). The Startup Guide describes the following: ⢠Basic operating instructions of your WALKMAN®. ⢠How to access useful PC applications websites on the internet. 3. Help Guid
L/A terminal sends continuous output when thermostat is set to EM HEAT mode, .... "A" or "L/A" terminal must be configured for Economizer in the installer setup. These terminals are powered by the cooling transformer. (Rc terminal). Terminal AUX 2 is
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will n
If you have a D0Link Cloud Router, you can take advantage of Zero Configuration Setup. This feature automatically configures your camera,s settings for you and adds it to your mydlink account. If you do not have a D.Link Cloud Router, you can use the
(See APP setup procedure for phone mode settings). * Set up backlight and service reminder when entering the setup mode the second time. Lorsque vous ...
24 avr. 2016 - expressly approved by Master Meter could void warranty and the user's authority to operate the equipment. ... to radio or television reception, which can be determined by turning the equipment off and on, the user is ... The installati
(See APP setup procedure for phone mode settings). * Set up backlight and service reminder when entering the setup mode the second time. Lorsque vous ...
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
If Green LED is not on, you may remove the Programmer and try again. 3) A Buzzer sounds for 1 second Indicating ready state for learning sequence - Press the ...
Programming Instructions: 1) Turn vehicle ignition key to ON position, without starting engine (Key-On Engine-Off - Position "1"). 2) Insert Programmer into OBD ...
19) When last key fob is programmed with the ignition OFF, remove and ... aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
If Green LED is not on, you may remove the Programmer and try again. 3) A Buzzer sounds for 1 second Indicating ready state for learning sequence - Press the ...
