Digitac Jazz Ultratab C725 Port de charge de remplacement

Utilisation du spudger, soulever les clips noirs jusqu'à un angle./ 90 degrés.. Tirer les câbles de données une fois que les clips sont à un angle de 90 degrés.
Télécharger le PDF
977KB taille 0 téléchargements 61 vues
commentaire
Report
Digitac Jazz Ultratab C725 Charging Port Replacement

ID de tutoriel : 36643 - Brouillon : 2019-03-26

Digitac Jazz Ultratab C725 Charging Port Replacement How to replace the charging port in the Digitac Jazz Ultratab C725.

Rédigé par: Savannah Brazzeal

© iFixit — CC BY-NC-SA

fr.iFixit.com

Page 1 de 6

Digitac Jazz Ultratab C725 Charging Port Replacement

ID de tutoriel : 36643 - Brouillon : 2019-03-26

INTRODUCTION The following guide will show you how to replace the charging port for the Digitac Jazz Ultratab C725.

OUTILS: Phillips #00 Screwdriver (1) Spudger (1) iFixit Opening Tools (1) Tweezers (1)

© iFixit — CC BY-NC-SA

fr.iFixit.com

Page 2 de 6

Digitac Jazz Ultratab C725 Charging Port Replacement

ID de tutoriel : 36643 - Brouillon : 2019-03-26

Étape 1 — Charging Port



Locate the four 3.5 mm Phillips head screws holding the silver back plate and the screen together. There are 2 screws on the top and another 2 screws on the bottom.



Remove all four screws with the Phillips #00 screwdriver.

 Remove the screws with the least amount of force. The removal of the screw will be more difficult if thread damage occurs.

© iFixit — CC BY-NC-SA

fr.iFixit.com

Page 3 de 6

Digitac Jazz Ultratab C725 Charging Port Replacement

ID de tutoriel : 36643 - Brouillon : 2019-03-26

Étape 2



Flip your device so that the long side without the buttons is facing you.



Insert the plastic opening tool between the silver back plate and the screen. From the corner of the device on either side, pry the seam of the device about 1 inch. 

With the plastic opening tool, pry the screen apart from the back plate.



Keep prying the screen apart from the back plate until they are separated.



With the plastic opening tool, if necessary, pry apart the remaining seams of the device.

 After the screen is loose, pull the screen towards you. Lift it to prevent damage to the buttons.

© iFixit — CC BY-NC-SA

fr.iFixit.com

Page 4 de 6

Digitac Jazz Ultratab C725 Charging Port Replacement

ID de tutoriel : 36643 - Brouillon : 2019-03-26

Étape 3



Locate the 3 black clips on the motherboard that hold the data cables./



Using the Spudger, pry the black clips up to a 90 degree angle./



Pull the data cables out once the clips are up to a 90 degree angle.



Repeat this for all 3 clips.

Étape 4



Locate the two 4.0 mm Phillips head screws that are holding the motherboard in place.



Use the Phillips #00 screwdriver to remove both of the screws.

© iFixit — CC BY-NC-SA

fr.iFixit.com

Page 5 de 6

Digitac Jazz Ultratab C725 Charging Port Replacement

ID de tutoriel : 36643 - Brouillon : 2019-03-26

Étape 5



The motherboard should now be loose.



To gain access to the charging port, flip the motherboard over.



Use the tweezers to pull the charging port off of the motherboard.

To reassemble your device, follow these instructions in reverse order. Ce document a été généré pour la dernière fois le 2019-07-23 07:53:55 AM.

© iFixit — CC BY-NC-SA

fr.iFixit.com

Page 6 de 6