This cover panel, right, for a 1942 Interstate, was copied directly from an original, left, using a form 'block, top, and a little perspiration.
EVERY CRAFISPERSON APPROACHES
Form Blocks Parti
a task with certain anticipation, acquired skills, and personal insight. After assessing the situation, he or she works up a build plan. Because many choices always offer themselves, sometimes it is only a matter of barometric pressure, in combination with it being a Tuesday evening rather than a Saturday morning, that yields a chosen angle of attack. Parts you can't weld, like wing ribs, are certain to be made using a f o r m i n g method such as form blocks (unless production costs dictate press forming dies). Ideal for the small shop, craftspeople have used form blocks since the 1920s and made them from hard wood, aluminum, epoxy, Fiberglas, plastic, or a combination of any such materials. Detroit car guys are now u s i n g the term " h a m m e r forming" for the same process, but I t h i n k their term needs a little more pizzazz.
Giving metal an unweldable shape KENT WHITE Tools & Materials The tools necessary for the parts I'm making here are common in the small shop: a saber saw with blades and speeds for cutting steel and wood, an oxy-acetylene torch for h e a t i n g and w e l d i n g , f o u r clamps, a hammer, and a few "cocking" tools, such as a driver and a blunt chisel. The needed materials also are common: plastic body filler, paste wax, some 12-inch lengths of light steel angle and strap, some plywood, and the aluminum sheet for the parts to be made.
The Process For these parts that are a little
bit detailed, I'll mold a receiver into which I'll pound the shape. This is analogous to half of a press f o r m i n g operation, where only the female die is made and the male die is s i m p l y a few shaped striking tools you use to whack and drive the metal into the receiver in a carefully organized fashion. Rather than applying 20,000 pounds of force to the male pressing die only once to form the part, we are applying 10 pounds of force 100 times (or so) to "chase" the metal part gradually into shape. From a variety of molding materials available I chose Bondo or polyester plastic body filler, but the stuff must be supported in a die box made of welded steel to prevent shattering of the plastic. I use a small steel welding table for tasks like heating and bending metal, but you don't need to scurry out for the parts to make one of these if you don't have one. Just clamp one end of the steel angle to
j
Sport Aviation
97
Our Firefly, Mark III C l a s s ! c f i d r ||Star, angi Slingshot all feature folding wings for easy storage/l§|D packs with o available..
Craft & Technique
THJENEVy
London, KY 606 • 862 • 9692 www.tnkolbaircraft.com email:
[email protected]
v
AIRCRAFT, CO.
FLIGHT PERFORMANCE RECORDERTM RECORDS entire flight on removable data cards for download and analysis on your PC GRAPHS the results in standard format for your Pilot's Operating Handbook NEW! FLIGHT PLAY BACK now displays flight instruments while replaying your flight path in 3D COMPLETE SYSTEM with sensors, GPS and software $2495. Fuel Flow option $250/$500. SOFTWARE AVAILABLE SEPARATELY
Recorder version with Flight Play Back $199 Manual version with test cards $49.
3D Flight Replay
OSHKOSH AIRVENTURE 2001 BOOTH 4150.
www.flightperformance.com
Pegasus Technotbgy, Inc.
703-250-5991
AIRCRAFT TOOL SUPPLY COMPANY USA and Canada call foil free
1 -800-248-0638 for your 104 page
Free Catalog and place your order
j ^
Online! anytime... from anywhere
www.aircraft-tool.com Over 3500 tools and equipment to choose from: Safety Wire Tools • Penumatic Riveters • GBP Riveters • Huck Riveters • Cherrymax riveting equipment • Cable Tools • RiveNut Tools • Air Drills • Drilling Aids • Rivet Sets • Bucking Bars • Rivet Guns • Riveting Kits • Engine Tools •
Aircraft Jacks • Test Equipment •Timerite • Sheet Metal Tools • Books & Videos
Telephone: 989 -739-1447 Fax: 989 -739-1448 For more information, visit SPORT AVIATION on the Web at www.eaa.org
Curving the steel angle for the die box involves heating and bending to stretch the edge.
your wooden bench with two clamps (so it won't slip under bending loads). Leave the free end in space to be heated and then bent by pushing hard on the end of it. I marked off the curve of the part's major line and used it as a rough reference while bending the 1-by-l-inch 1/8-inch thick steel angle. Heating the steel to a cherry red color is the region of plastic heat, which allows the metal to stretch evenly and easily. Marking again for length, I cut the curved angle and laid it up to the pre-sawn angle for the opposite side, clamped it down, and tack welded. The flat strips are laid up on the angle frame as backing and then tacked as well, using the original part as a guide. When all pieces are in place you have an open-ended box that is ready for welding, though only enough welds for m e d i u m strength and for keeping most of the plastic filler from gooshing out under molding pressure. After welding I remove the loose scale with a wire brush and wax the o r i g i n a l part I wish to copy. Mixing the plastic filler to a 98
SEPTEMBER 2001
The steel die box, right, is made of four pieces welded together, along with two clamping tabs, and matches the original, left, fairly closely.
The waxed original is smooshed into the die box cavity and then clamped until the filler hardens, making the receiver an exact copy of the original.
factoryfive.com At Factory Five Racing we're serious
about engineering excellence. Maybe that's why our cars have so completely dominated the component car industry for the last five years running.
$10,990 Complete All you need to build your car is the running gear from a late model Mustang 5.0 and our pkg. The FFR chassis is engineered specifically to use these tough Ford drivetrain components.
The unique combination of modern running gear and classic design delivers world class performance that dominates at the track, yet is reliable and comfortable on the street.
To find out more, or to receive our free detailed information package, please call 508-291-3443. You can also visit our
website at www.factoryfive.com.
Factory Five Racing, Inc.
factoryfive.com Call 508-291-3443 forFree Brochure
Mustang and Cobra an rrgisteml trademarks. Factory Five Racing, Inc. is not connected lo the holders of these marks. 41300D01 Factory Five Racing, Inc. 18 Kendrick Road Wareham. MA 02571 For more information, visit SPORT AVIATION on the Web at www.eaa.org
Sport Aviation
99
Craft & Technique
Rather than applying 20,000 pounds of force to the male pressing
die only once to form the part, we are applying A sized aluminum blank is first annealed and then clamped tight, using the wood as an upper form to hold the definition of the curve.
smooth consistency is a job for a triangle whipper whirled by a drill motor. You don't need air bubbles mixed into the mold, but we do need a very smooth batch of filler. Glop the filler into the die box and quickly smoosh the original down into the mess. I grab the
preset clamps and cinch 'em tight, making sure to keep the alignment true. After the f i l l e r h a r d e n s , I remove the original part and flip the receiver over to knock off the stalactites and goobers hanging out the back, where my skip welds
10 pounds of force 100 times (or so) to "chase" the metal part gradually
into shape.
All Epoxies Are Not Created Equal! PTM&VV Industries introduces AKROI'OXY. the first cpoxy laminating resin to combine modern non-toxic hardener technology with superior high temperature cured strength. Kasy to use. AKROI'OXY is specially formulated for engine cowlings, wing spars, landing gear legs, and other Quality Materials For High Performance Composite Parts very high performance applications.
Manufactured by PTM&W Industries, Inc. Santa Ke Springs, CA 90670
Call 800-421-1518 For more information, visit SPORT AVIATION on the Web at www.eaa org
1OO
SEPTEMBER 2001
Australian designed and manufactured
left a few gaps. Cleaning up the surface of the plastic is the work of a minute, and then the fresh a l u m i n u m panel is sized, annealed, and clamped in place for the fun part. D i f f e r e n t alloys work d i f f e r ently in this situation, with 5052 requiring many annealings and 1100 requiring none. Because I used 3003, I annealed it once in the beginning and yet had a part plenty hard and stiff enough for service at the end. The clamping tabs are a big help when the receiver begins to walk away in the middle of h a m m e r i n g out the part, so remember to weld them on before adding the plastic. Using a "cocking tool" or "driver" is very helpful and is an old tradition. One spelling has it as a "caulking" tool, but we are not replacing windows. Webster gives the satisfactory definition of cocking as, "to turn up or tilt." So, we turn up the edge by driving the metal down into the receiver with our "cocking" tool. I use a variety of hammers to work the tools and have a fine collection of 8-, 12-, and 16-ounce ball-peen hammers for this purpose. I do prefer a nice 2, 3, or 4x pneumatic hammer with the air carefully set for rapid work, however, and teach many satisfying techniques for this in workshops. This particular method is called "flow forming" and dates back to the 1930s aircraft environment. When you f i r s t see the metal move really fast with this technique, you know exactly why it is called flow forming. You must proceed with caution, as any heavy hit can tear the metal, especially down in the corners where 1 use a blunt chisel for the details. After working all of the metal down into the receiver, I go over it carefully to make a s m o o t h i n g or f i n i s h pass. Any sanding at this point endangers the thin metal, so I rely on planishing for a cleanup. Sport Aviation
101
Jabiru Aircraft ' Purpose designed aircraft engine. > Direct drive & air cooled. . World's lightest | 80 & 120hp, 4-stroke, 4, 6 & very shortly | an 8 cylinder engine 180-200 hp. i Proven safe & reliable with nearly 1,500
In Loving Memory of Ethel 7/27/14-4/27/97
engines sold into 50
AIRCRAFT ALUMINUM
country's and into 75 aircraft types.
2024 T 3 ALCLAD 48" WIDE ALL PRICES PER RUNNING FOOT
.016- $9.20 .020-$10.95
.025-$12.10
.032—$13.75 .040-$18.50
> Installation packages available in most popular kitplanes.
.050-$23.50 .063-$29.10
.080-$34.95
A dream come true that's ready to install. For more info please contact a dealer
.090 —$40.70 .125-$56.50
near you.
ALSO ALLOYS OF VARIOUS TYPES: 3003 H 14 ... 5052 H 32 ... 6061 T 6 ... 2024-0 CALL FOR PRICES ON ...
4130 Steel Tubing & Plate, Reamers, Rotary Files, Drill Bits, Hydraulic Hose, Crimpers, Air Duct, Rod Ends, Tie Downs, Nuts, Bolts, Rivets, Extruded Aluminum, Quick Release Pins, Counter Sinks, Safety Wire, Sheet Metal, Wire Strippers, Aluminum Tubing and Bar Stock. MANY MANY MORE ITEMS . . . JUST CALL ! ! ! Free Catalog Available
Jabiru USA Flight Center, LLC Peter Krotje— 1091 Stillmeadow Ln, Menasha Wl 54944 Ph: V800-JABIRU1 Fax: + 19207577711
Email:
[email protected] Web:
Suncoast Sportplanes, Inc
AIRPARTS, INC.
Andy Silvester & Karl Geng 2003 Mainsail Dve, Naples, FL 34114
2400 MERRIAM LANE KANSAS CITY, KS 66106 913/831-1780 FAX 913/831-6797
1-800/800-3229 www.airpartsinc.com
www.usjabiru.com
Ph: + 1 941 389 2027 Fax: + 1 941 430 2063 Email:
[email protected] Web:
wwwsunroastjabiru.com
The 4-plac& aiut&fk kh which starts at just $23,500.
Imagine building and flying your own plane, able to make 1240 NM cross country trips, carrying four adults with luggage in comfort - at speeds over 200 mph! Choose from seven models, with a wide range of available options. Sleek, fast, stable and efficient...the perfect description for Velocity sport aircraft.
^^ ^^W^W^^(MBM^BIi^^ ^^H^»^^ ^^\^^^fp
velocityaircraft.com
30 min Video & Info Pak $29.50 US & Canada $39.50 International (Visa/MC/Check/US$ Money Order)
200 W Airport Drive, Sebastian FL 32958 • (56!) 589-1 860 For more information, visit SPORT AVIATION on the Web at www.eaa.org
Craft & Technique The schnooble I've chosen to drive the metal Into the receiver is plastic over steel.
••IHIIII
CENTER
T »I1K A l l
c^ 5T 1 i
This blunt chisel Is a "cocking" tool, and it is used to define a corner and other details.
£5.6 VS&ttBO '>K I \'
N. »
AUTOTXACK '
A final t r i m , and the part is
I •i zI, . Ui-U
ready for fit and hole drilling. If I
^x.^v.jT '15 M—
_CC
—. I?
7 ."! vf/ as ^ ?SC
i-R-IX
•i •» -'IS ^ ^% *ir
... te