The device under test is manufactured by the grantee (Continental Corporation) and sold as an OEM product. Per 47 CFR 2.909, 2.927, 2.931, 2.1033, 15.15(b) etc…, the grantee must ensure the end-user has all applicable / appropriate operating instructions. When end-user instructions are required, as in the case of this product, the grantee must notify the OEM to notify the enduser. Continental Corporation will supply this document to the reseller/distributor dictating what must be included in the end user’s manual for the commercial product. INF ORMATION TO BE INCLUDED IN THE END USER'S MANUAL The following information (in blue) must be included in the end product user’s manual to ensure continued FCC and Industry Canada regulatory compliance. The ID numbers must be included in the manual if the device label is not readily accessible to the end user. The compliance paragraphs below must be included in the user's manual. ****************************************************************************** FCC ID: M3N74295202 CAN RSS-Gen/CNR-Gen This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. ******************************************************************************
are required, as in the case of this product, the grantee must notify the OEM to notify the end- user. Continental Corporation will supply this document to the ...
The following information (in blue) must be included in the end product user's manual to ensure continued FCC and Industry Canada regulatory compliance.
ensure continued FCC and Industry Canada regulatory compliance. The ID ... This device complies with Part 15 of the FCC Rules and with Industry Canada.
The ID numbers must be included ... license-exempt RSS standard(s). Operation ... “IC:” before the radio certification number only signifies that Industry Canada.
are extremely well proven designs. They are not flawless, but each engine's spe- cific weakness is well understood, with many fixes available in the aftermarket.
YEAR. 2 of 5. 01. 28. 2003. P.O. Box 90 Mobile Alabama ⢠251-438-3411. SIL 03-1. Prior to operation and/or storage in cold weather, ensure that the engine is ...
Contains Useful Information Pertaining To Your Aircraft Engine ... The following procedure is required for preheating, starting, warm-up, run-up and takeoff. 1.
Thunderbolt with a 2-year, 200-hour war- anty while the Extreme engines boast power boosters such as higher compres- sion, along with a l-year, 100-hour war-.
Connect the CONDENSATE DRAIN, using flexible tubing or PVC pipe into one of the ..... damage, direct, incidental or consequential (including, but not limited to, ...
Mar 9, 1987 - ASCII Octal and Hex Formats, Codes 30 37 and 50 58 . ..... here. Note: Insert the Device List Disk in the PC disk drive, not in the programmer disk drive. ..... Place the Boot Files disk in the programmer disk drive (see page 2 10). Not
Mar 9, 1987 - Page 1 ... Portions of the 2900, 3900, and 3980 Programming Systems are protected under U.S.. Patent numbers ...... that device, including manufacturer, part name, programmer menu name, ... the following safety standards: ... The MatchB
B. Impulse coupling cam assemblies not meeting the criteria of this bulletin ... between the stop pin and flyweight to determine clearance ("X" of Figure 4) while.
which exceed the dimension shown in Figure 1 must be discarded. Oversize counterweight ... interference fit, (see Figure 2). Upon installation, check the ...
In the interest of safety, TCM is recalling and replacing all capacitors P/N 10-349276 with date codes .... corner of the magneto data plate, near the word. "TYPE".
Jul 16, 1990 - Service history of these valves has been excellent and unparalleled in the ... condition has progressed at the time of overhaul to the extreme ...