Install PICOPLA Piccopla operates on Windows 98/NT/2000/XP platforms Installing procedure: 1. 2. 3. 4. 5.
Download Picpla.zip file from the Nordic ID web. Extract Picpla.zip. (Winzip, Pkzip, ..) Run setup.exe. Follow instructions of setup program. Run Piccopla from Start->Programs->Piccopla
If version conflict message occurs during setup, press [No to all] button. If sharing violation message occurs during setup, press [Ignore} button. Connecting PiccoLink devices to the PC The hand terminals are connected to the PC with the Desk Top Charger and the base station cable.
The base stations are connected to the PC with base station cable.
Connecting Piccopla
Hand terminal settings When editing values in text boxes, press enter to apply changes. Heading
The hand terminal´s initial display heading text. Max 20 characters.
Extra ID
The hand terminal sends this ID to the HOST (0-255)
Password
Change of password (0-9999)
Sleep timeout
The time in which the hand terminal changes to standby-state. (5-55 seconds).
Volume
Beep level. Three different levels.
Key sounds
Enables/disables key sounds.
Reception time limit
The time limit during which the base station must respond to the hand terminal before the message is sent again.
Resending times
How many times a message is sent to the HOST if no answer is received.
Menu Language
Sets the hand terminal´s menu language.
Enable RECEIVE mode by KB.
Enables/prevents changing the RECEIVE mode in the hand terminal.
Battery type
Select Recharg. if using NiCD or NiMH rechargeable batteries, Alkaline if using normal batteries.
F-key text
Setting function keys F1-F10. You can define a 15-character long text under an F-key. F-keys can be defined in two different ways: to print in the field or to be sent to the HOST.
Use formlock
Formlock feature prevents the problem when the host receives the message from the hand terminal,but the hand terminal does not receive the answer from host. After transaction failure,the user cannot modify the values in the fields before sending again. If the formlock is enabled,a user defined message prompts to hand terminal display.
Use default text
The default message of formlock prompts to hand terminal display instead of user defined.
Base station settings Four different operation modes: Normal
Normal operating with the hand terminals
Relay
The relaying Base Station is giving echo from the PiccoLink communication existing in the air back to the air, and thus increasing the reception area. The echo doubles the existing communication in the air, and thus decreases the transmission of coefficient in the channel.
Site Survey
When estimating how many Base Stations are needed in a certain environment it is advisable to use as a help tool the "Site Survey" Base Station. The "Site Survey" Base Station can be used to estimate a receiving area of one Base Station. "Site Survey" Base Station requires only power supply. It answers automatically a connection quality information to the Hand Held Unit which are: GOOD, AVERAGE or POOR.
Sub Station Modem The SSM mode of the RF600 base station allows for asynchoronous (SSM) transfer of arbitrary data between the host and the SSM base station.
The RF600 SSM mode protocol document
Uploading Firmware files to the hand terminal Update mode: 1. Make sure that batteries on the hand terminal are good. 2. Place the hand terminal to the Desk Top Charger 3. Remove charger power supply if connected. 4. Connect the BS-cable between the PC and the Desk Top Charger 5. Run Piccopla 6. Select COM port and press 'Read Target' 7. Check from FW-version number, is updating necessary?. 8. If FW-file is not loaded on your computer, select 'Downloads' tab and dowload proper FW-file. 9. Select 'FW-update' tab. 10. Select 'Update' radio button. 11. Open FW-file 12. Press 'Start uploading' button. 13. Wait. (Do not work with PC during updating) If an errors occurs during updating, then the device is not programmable by 'update mode' anymore. Then the device must be reprogrammed by 'Boot mode'.
Boot mode: 1. Remove batteries from the Hand Terminal. 2. Connect the 'Boot cable' between the PC and the hand terminal. 3. Run Piccopla. 4. Select COM port. (do not press 'Read Target' button) 5. Select FW-update tab. 6. Select 'boot' radio button. 7. Open the suitable FW-file. 8. Press Start Uploading button. 9. Place batteries back to the hand terminal and click OK. 10. Wait. 11. After uploading, remove batteries from the hand terminal. 12. Remove 'Boot cable'. 13. Place batteries back to the hand terminal. 14. The hand terminal is in use again. Uploading Eeprom and Laser Scanner Settings
The Eeprom settings are variables used by firmware. All user defined values are stored in eeprom memory. Eeprom memory will keep values even if batteries are taken off. Extension of the eeprom settings file is (*.epr) The eeprom setting files are text files which contains specific values for the PiccoLink eeprom. Nordic ID provides an *.epr files. Typically, eeprom settings will be loaded together with new FW. To upload *epr files to PiccoLink device: 1. Select FW-update tab 2. Press 'Open eeprom settings file' button and browse for correct epr file. 3. Press 'Start uploading' button.
The builtin Laser Scanner can be configure by the users settings. Programming manual of the scanner provides the programming codes. Extension of the scanner setting file is *.lsr which contains several commands to the laser scanner engine. lsr file example: //Laser settings file //Format is L::Comment L:ZA:Set Factory defaults L:HD:CTS mode Low to transmit. Required by PiccoLink L:PB:Enabled interleaved 2 of 5 without check digit. L:PD02:Set min length for int 2 of 5
L:PE32:Set max length for int 2 of 5 L:BH30:Scanning timeout. x*100ms Downloading PiccoLink softwares from web
Piccopla connects to Nordic ID web site and provides: • • •
Dec 29, 2013 - A VPN(virtual private network) allows us to connect directly to our home private network over ... private networks by creating a tunnel between the client in a ... secure your pfSense web interface ASAP to prevent from snooping ...
Cisco Secure VPN Client Solutions Guide. OL-0259-01. Configuring and .... Generate the public and the private keys. The crypto key generate rsa-usage ...
Nov 30, 2016 - To complement our solution we've added IP SLA tracking so that R1 will continuously monitor the Linux proxy to ensure it has ... R1(config-ip-sla)# ip sla schedule 1 life forever start-time now .... Cisco Password Crack (/cisco-.
Yes. 12-hour format with leading zeros and lowercase am/pm. â08:00pmâ. PHP date format âh:iaâ. 1.4 Set meta-tag to stop robots crawling. JEvents creates a lot ...
Console and vty access: username: ccna, password: cisco. ⢠enable secret: .... Examine the state of the port-channel 1 interface on your switch. PxSW#show ...
Dec 30, 2012 - Windows Server 2012 as required by one of the practice exercises in this chapter. â¢. You will ..... private cloud. For more information on Microsoft private-cloud solutions, see ..... These include WMI, Active Directory Domain Servic
Topic 1, Installing Windows XP Professional (22 questions) . ...... Explanation: There is not a parameter for specifying the mini-Setup Wizard answer file.
The most common initial deployment of MSTP and RSTP is in the backbone and .... If the superior information received on the port causes the port to become a ...
For example, ssh admin@ipt-1. Direct Connection. From a direct connection, you automatically receive this prompt: ipt-1 login: where ipt-1 represents the host ...
The UCC3895EVMâ001 evaluation module (EVM) is an isolated 48-V input ... OUTB signals must first transition through a signal transformer before being fed ...
Standard shipment of Z91N come with thermal compound applied to the heat sink already. Remove the foil which protects the compound. Carefully put back the ...
May 27, 1999 - infrared. ⢠USB. Initial Installation of Windows NT Server 4.0: We strongly recommended that you install the Windows NT operating system with ...
Jul 27, 2012 - VPN red, and both have the same private IP address 192.168.1.0/24. Because the clients have the same IP address, the DHCP relay agent and ...
Information About a Load-Balancing Scheme, page 2. ⢠How to .... If the bulk of the data passing through parallel links is for a single pair, per-destination load.
Recovering Server Roles and Configuring High Availability . . . . . . . . . 719 ...... Ultimate on your network, but this is not essential. The client ..... There are two different types of functional level in Windows Server 2003: the domain ...... a
Groove, Internet Explorer, Outlook, PowerPoint, SharePoint, SQL Server, Windows, ...... The following software is required to complete the practice exercises: ... Format (PDF), and you can view it by using Adobe Acrobat or Adobe Reader. .... and deve
Copy the file plugins/jevents/customfields/templates/fieldssample16.xml to plugins/jevents/customfields/templates/fields.xml. If you are using Joomla 1.5.
noip.com is one of the few dynamic DNS free services that are reliable to use. If you have, like in my situation, a. RaspberryPi connected to your home DSL and ...
Sep 26, 2016 - SQL Server servers module and how to. Objectives completing. SQL. SQL post-installation ... enterprise significant issue. might ... Windows designed for server. Module 2: Installing and Configuring SQL Server 2014 ..... involve. To per
