Caution:this plane is not a toy! Before use ,please carefully read this
Use two screws of each sides to ensure the wings fixed upto the fuselage. Repeat the above steps on the other side of the fuselage. Fix up the wheel to the.
Caution:this plane is not a toy! Before use ,please carefully read this manual.
Wing Span:80in/2030mm;
Flying Weight:5200-5900g;
Wing area:79sq.dm;
Radio:4channels 6servos;
Length:70.8in/1800mm;
Engine:50-60cc Gas;
Cut away covering film for the servo.
Attach the aileron to the main wing with AB glue.
Screw the servo to the wing. Put the servo extension through the wing and pull through the wing root rib.
Link the servo and tri-horns with pushrod and straper.
Find out the holes on each sides and cut off the film of fuselage.
Connect the main wings and the fuselage with joiner. Also pull the extension into the fuselage.
Use two screws of each sides to ensure the wings fixed upto the fuselage.
Repeat the above steps on the other side of the fuselage.
Fix up the wheel to the screw by two collars.
Screw the wheel to the landing gear. Be assured that the screw is fixed up.
Install the wheel cover, and fix it up to landing gear with two TP screws.
Bolt landing gear strut to fuse with 4 bolts and washers.Ensure tapered edge of the gear strut is facing toward the rear.
Measure the right position and remove the film from the stabilizer.
Glue the stablilizer to the fuselage.
Connect the aileron and the stabilizer by hinges, and glue them.
Connect the rudder to the fuselage by hinges by AB glue.
Link the elevator servo to the elevator with pushrod.
Repeat the above step on the other side .
Insert rudder cable through the brass swage tube,then through the threaded coupler hole,and back through the brass swage tube as shown.
Loop the cable back through the brass swage tube as shown.
Attach a metal threaded RC link to each threaded coupler.Attach the RC links to the rudder servo arm and then attach the servo arm to the rudder servo as shown.
Fix the tri-horns to the fuselage as shown.
Attach straper to rudder control horn on both sides of the rudder.
Attach the tail wheel to the tail landing gear as shown.
Mount the tail wheel struts and springs using four TP screws.
Mount the tail wheel steering tiller using two TP screws.
Attach the steering springs on both sides of the tail wheel to the rudder tiller and tail wheel tiller. Center the springs between both tillers.
Drill the engine mounting holes as the board provided.
Insert the bolts through flat fender washers,the firewall and into the engine stand offs. Tighten firmly.
Engine final assembly is completed.
Install the linkage servo as shown.
Fixup the canopy with TP screw on each side of the canopy.
Aug 23, 2005 - Line Plans ... We think Skytex is the best all around package available. ..... The glider is laid out on its top surface, the lines are untangled and ...
most efficacious equipment in their struggle for survival, are embedded in ..... We would perceive motions, but neither buying nor selling, nor prices, wage rates,.
Suivant le type d'impact, unaccident, mémeatres faible vitesse, peut entrainer unrisque de ... N'utilisez pas de détergents ou de produits dérivés d'ammoniaque ...
This preventive maintenance program is designed to ensure that all critical ...... Be sure the exhaust pipe and muffler are cool before cleaning the spark arrester.
Power draw MCM10. W. 5. Rated voltage BUS. DC ⦠V. 15. Internal appliance fuse, heating pump output. Amp. 5 AF, ceramic, filled with sand. Measuring range ...
Engine: D21B. D28M. Type: Rear Exhaust Without Pull-start. Rear Exhaust With Pull-start. Cylinder ... STS engine is designed and manufactured for high level of.
Use your Quest regularly to help reduce your weekly vacuuming ..... To reduce potential radio interference to other users, the antenna type and its gain should ...
Jul 29, 2011 - China delays Harry Potter release in favour of Communist party epic ... released on 4 August; Transformers: Dark of the Moon on Thursday ...
Wait at least 10 minutes after removing electrical or vacuum power from the aircraft and/or gyro before removing gyro. DO NOT remove a gyro while it is running.
Wait at least 10 minutes after removing electrical or vacuum power from the aircraft and/or gyro before removing gyro. DO NOT remove a gyro while it is running.
supplier or your fire service. Leaking gas may cause a fire or explosion, which can cause serious bodily injury or death, or damage to property. INFORMATION ...
A Do not add charcoal starter fluid or charcoal impregnated with charcoal lighter fluid to hot or warm .... securing the gas line and orifice into the burner tube is.
In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed ...... so that they do not move during the following steps. ...... The next maneuver is somewhat more tricky than it looks.
to the Cessna 182 ARF visit the Top Flite web site at ... We use the Robart Super Stand II. (ROBP1402) .... recommend Great Planes Pro⢠CA and Epoxy glue.
Instead, use a drip pan to catch drippings from meat when cooking ..... CharBin" storage container holds a bag of charcoal with a maximum weight of 30.
A WARNING-secure UMBRELLA CANOPY to the CO-SLEEPER brand bedside bassinet or playard by fastening all Velcro' tabs. (Umbrella Canopy is an optional accessory) ...
Extinguish any open flames. 3. ... A Do not use petrol, liquid fire starter or alcohol on the charcoal at any time. ... A Do not use a flame to check for gas leaks.
Contact the AMA for a rule book with full details. IMAA .... Great Planes Pro Threadlocker⢠(GPMR6060). â Heat shrink ... Here is a list of optional tools mentioned in the manual that will help you .... 90 100 110 120 130 140 150 160 170 180.
Rashi comments (ibid. 12) in the name of an aggadic Midrash, based ... âKelalosâ minus two (in Parshas Ki Savo), besides the forty- nine in Torat Kohanim ... Acts as a Barrier between the Curses and Rosh HaShanah ... After hearing the âtochacha
A relocatable power tap provided with auxiliary lighting features is not for permanent installation. Do not permanently mount or remove the plug for permanent connection to the electrical system. ⢠Caution marking and rating plate are located at re