Jan 19, 2009 - Water Bottle and its Support ................................................................................................................... 3. Step 1: Water Bottle Geometry: Curve ...
Version 5 Release 19 January 2009 EDU-CAT-EN-DL1-FS-V5R19
CATIA Developed Shapes
Detailed Steps
Table of Contents Water Bottle and its Support ................................................................................................................... 3 Step 1: Water Bottle Geometry: Curve Development ......................................................................... 3 Step 2: Water Bottle Geometry: Create the Reinforcements .............................................................. 4 Step 3: Water Bottle and its Support: Insert a New Part ..................................................................... 6 Step 4: Support Geometry: Create Three Holes and Unfold............................................................... 7 Step 5: Support Geometry: Create an Opening ................................................................................ 10 Step 6: Support Geometry: Unfold the Geometry ............................................................................. 12
COPYRIGHT DASSAULT SYSTEMES
2
CATIA Developed Shapes
Detailed Steps
Water Bottle and its Support Step 1: Water Bottle Geometry: Curve Development • Load Water_bottle_step_01.CATProduct • Double click on Bottle step 01 to activate the CATPart • Click on Develop icon • Configure the option as follow:
COPYRIGHT DASSAULT SYSTEMES
3
CATIA Developed Shapes
Detailed Steps
Step 2: Water Bottle Geometry: Create the Reinforcements • Load Water_bottle_step_02.CATProduct • Create sweep by clicking the sweep icon
• Click on rectangular pattern to duplicate vertically the sweep
Click Reverse if necessary
• Join the Rectangular Pattern and the sweep COPYRIGHT DASSAULT SYSTEMES
4
CATIA Developed Shapes
Detailed Steps
• Trim this join with the revolute
Choose the right side to keep
• Use edge fillet to have the final shape
COPYRIGHT DASSAULT SYSTEMES
5
CATIA Developed Shapes
Detailed Steps
Step 3: Water Bottle and its Support: Insert a New Part • Load Water_bottle_step_03.CATProduct • Load Bottle_support_start.CATPart • Drag and drop the CATPart into the CATProduct.
COPYRIGHT DASSAULT SYSTEMES
6
CATIA Developed Shapes
Detailed Steps
Step 4: Support Geometry: Create Three Holes and Unfold • Load Water_bottle_step_04.CATProduct • Create the sketch on zx plane
and extrude it
• Split the cylinder with this extrusion
• Create the tearing line in a sketch with plane.4 as support
COPYRIGHT DASSAULT SYSTEMES
7
CATIA Developed Shapes
Detailed Steps
• Project the sketch on the surface as a nearest solution.
• Unfold the geometry on plane.2
COPYRIGHT DASSAULT SYSTEMES
8
CATIA Developed Shapes
COPYRIGHT DASSAULT SYSTEMES
Detailed Steps
9
CATIA Developed Shapes
Detailed Steps
Step 5: Support Geometry: Create an Opening • Load Water_bottle_step_05.CATProduct • Create a sketck on yz plane
• Extrude it
• Split the cylinder with the extruded shape
• Create a Parallel Curve. COPYRIGHT DASSAULT SYSTEMES
10
CATIA Developed Shapes
Detailed Steps
• Create a plane.5 offset to Plane.2.
COPYRIGHT DASSAULT SYSTEMES
11
CATIA Developed Shapes
Detailed Steps
Step 6: Support Geometry: Unfold the Geometry • Load Water_bottle_step_06.CATProduct • Unfold the geometry on plane.5 • Select Surface Type as ‘All’.
• Click ‘NO’ for following warning.
COPYRIGHT DASSAULT SYSTEMES
12
CATIA Developed Shapes
Detailed Steps
• Transfer the Parallel.1 on unfolded surface. • Here the ‘Unfolded Surface’ will automatically get selected upon selecting the ‘Surface to unfold’.
Jan 19, 2009 - Developed Shapes. CATIA V5 Training .... a New Part. 5 min. In this step, you will use ASD functionalities to insert a new part in the assembly.
Jan 19, 2009 - Develop wires and points onto a revolution surface. Targeted ... Develop Wires: Concept Definition. 15 ..... options to position the result ...
Jan 19, 2009 - Right click on them, choose âDeactivateâ. ⢠Click âRotation Mesher â icon. ⢠Select the tetrahedron filler mesh for the meshpart. ⢠Select the ...
Academy of Graphic Arts and Book Design (HGB), was ... Latin Extended. 1 Jan Nave, Miss ... This specimen pdf is intended for evaluation purposes only.
works a flat sheet into a completely finished ... mensions to the flat sheet. To allow for slippage cut .... man or woman, to contact him in re- gard to preserving the ...
This software is intended to the children at the first and medium levels of the nursery school, as they are getting familiar with shapes, sizes and colors.
Jan 19, 2009 - parts and assemblies designed in CATIA. This course focuses .... and post-process the part or assembly in the case study. Each step contains ...
Each case study contains a set of model requirements, known as the design intent. The first case study does not contain a design intent because you are not ...Missing:
Aug 19, 2008 - August 2008 .... Individual case studies are used as building blocks towards the completion of a final .... CATIA V5 is specifically designed for the Windows operating environment, and ..... The documentation may also be installed on a
Sep 19, 2008 - Housing part as there is NO conflict between the geometrical and assembly constraint. ...... Calculated in Clash, Clearance, Contact. Yes. No.
Jan 19, 2009 - Select new Product in the specification tree (orange highlight) ... Page 5 ... Select in the dialog box the design table icon corresponding to ...
Aug 19, 2008 - To create spline or a polyline, you only need points. And to create a circle, you only .... Important: the curve is deformed and you control the maximum deviation ...... And stress the fact that it requires a lot of work. This is far f
Sep 19, 2008 - Use an image as a background or as a basis for design. - Import an .... wireframe elements like points and curves in FreeStyle workbench.
Sep 19, 2008 - EXERCISE BOOK. Copyright DASSAULT ... CATIA Freestyle ... In this exercise you will create sketches which represent the side and top views.
photocopying, recording or otherwise, without the express prior written permission of DASSAULT SYSTEMES. This courseware may only be used with explicit.
Aug 19, 2008 - Select this edge to be filleted and key in a 3mm radius value: 3.7 - You are going to create a multi-edge fillet on the previous surface: ⢠Click on ...
Jan 19, 2009 - Macros Options Interface. 34 ..... This kind of applications can be developed in: ..... It is possible to develop an application in Visual Basic, then.
20 min. Modify spline control points. Modify a surface profile sketch. Modify a surface fillet radius. Button and Mouse Exercises. Topics covered: Mouse Exercises ...
Sep 19, 2008 - Students attending this course should have knowledge of CATIA ... Common Knowledge Tools Exercises ...... project's design specifications.
Sep 19, 2008 - CATIA Product Design Expert ... First load all the components from Companion into CATIA V5 and save them ... following assembly constraints:.
Sep 19, 2008 - Create two Arcs of Radius 70 mm in Sketch.4 on YZ plane. Create a ...... manual coupling with definition of the coupling curve(s). Automatic ...
Jan 19, 2009 - create simple parts in CATIA V5 and understand how to create a structured part, understand how to manage parts in the context of an assembly ...