Setting Up this Device Connect the cables as detailed in the diagram overleaf, then follow the steps below to complete the setup of the Avaya Scopia XT Camera Switch. For details on how to use the system after setup, see the User Guide for Avaya Scopia XT Series or the Quick Start Guide for Avaya Scopia XT Series.
CAUTION: Make sure all units are switched off whenever connecting or disconnecting devices.
Step 1. System Installation
Step 6.
Place the Avaya Scopia XT Camera Switch on a horizontal surface close to the XT Codec Unit. Maximum supplied cable length is 40cm (0.13ft).
Connect the second camera as follows: 1. Connect the 10-meter VISCA Control cable supplied with the camera kit: a. Attach one end of the VISCA control cable to the IN RS-232C connector on the second camera. b. Attach the other end to the OUT RS-232C connector on the first camera. 2. Connect the DVI-HDMI cable as follows: a. Attach the DVI connector to the DVI socket on the second camera. b. On XT5000, Attach the HDMI connector to the HDMI socket labeled 2 on the Scopia XT Camera Switch. On XT7000, Attach the HDMI connector to the HDMI socket labeled 1 on the Scopia XT Camera Switch. 3. Connect one end of the power supply cable to the DC IN 12V connector on the camera, and the other end into one of the power sockets on the wall.
Step 2. one end of the HDMI cable to the OUTPUT socket on the Scopia XT Camera Switch - On the XT5000 Codec Unit, connect the other end to the available HDMI input. - On XT7000 Codec Unit, connect the other end to the HDMI2 input. 2. Connect one end of the USB cable to the USB socket on the Avaya Scopia XT Camera Switch and the other end to the upper USB connector on the XT Codec Unit. 1. Connect
2
1
HDMI
USB
Second Camera
4 4
3
2
2
3
1
1
1
1 USB
9
12
12
678
DC IN 12V
Step 3. Check that the SYSTEM SELECT switch on the back panel of each camera is set to 7:
SYSTEM SELECT
345
HDMI
2 345
Avaya Scopia XT7000 Codec Unit
1
First Camera
9
Avaya Scopia XT5000 Codec Unit
3
Quick Setup Guide
678
4
Avaya Scopia® XT Camera Switch
IR SELECT 123
IN RS-232C OUT
DVI
DC IN 12V
SYSTEM SELECT
IR SELECT 123
IN RS-232C OUT
DVI
1 XT Camera Switch Connected to XT5000 2 XT Camera Switch Connected to XT7000
345
9
12
678
DC IN 12V
SYSTEM SELECT
IR SELECT 123
IN RS-232C OUT
DVI
Step 4.
Step 7.
Connecting the first camera Insert the three connectors of the camera cable (3 connectors on one side, 2 connectors on the other side) to the sockets on the back of the camera: 1. The DVI connector to the DVI socket. 2. The 8-pin connector to the IN RS232C socket. 3. The power connector to the DC IN 12V socket.
If required, repeat the above step for a third or fourth camera.
Step 8. 1. Switch
12
9
345
678
DC IN 12V
SYSTEM SELECT
IR SELECT 123
IN RS-232C OUT
DVI
Step 5. Attach the two connectors on the other end of the camera cable: 1. On XT5000 Series, connect the On XT7000 Series, connect the HDMI connector to the HDMI first camera directlyto the HDMI1 socket labeled 1 on the Scopia port of the codec, as in single XT Camera Switch. camera setup.
on the Scopia XT5000 or XT7000 unit, the cameras and the XT Camera Switch. 2. Set Configure > General > Show Advanced Settings to Yes 3. Set Configure > Advanced > I/O Connections > Cameras > General > XT Camera Switch detect mode = Yes. (default PIN for Advanced configuration is 1234)
Step 9. 1. Setup
each camera in the GUI section Configure > Advanced > I/O Connections > Cameras as explained in the “Deployment Guide for XT Series”.
345
9
12
678
DC IN 12V
SYSTEM SELECT
IR SELECT 123
IN RS-232C OUT
DVI
1
2. The connector for power and serial control to the socket on the XT Codec Unit.
horizontal
Avaya Scopia XT Camera Switch enables all the endpoints of Avaya Scopia XT5000 and XT7000 series to be connected with up to four HD Cameras or four generic HDMI devices (such as DVD and generic media players). The Avaya Scopia XT Camera Switch is fully powered and controlled from the Avaya Scopia XT endpoint. The switch can be controlled from XT User Interface and Remote Control.
Package Content: • Avaya Scopia XT Camera Switch • Cable USB 40cm • Cable HDMI M/M, 40cm
Avaya Scopia XT Camera Switch Quick Hardware Setup
6
4
9
CAUTION: the mains cable is used as a disconnecting device, use therefore an easily accessible outlet located near the device for the power supply connection. Never remove the mains plug while the device is connected.
CAUTION: the mains cable is used as a disconnecting device, use therefore an easily accessible outlet located near the device for the power supply connection. Never remove the mains plug while the device is connected.
IR SELECT 123
IN RS-232C OUT
DVI
DC IN 12V
SYSTEM SELECT
9
IR SELECT 123
IN RS-232C OUT
DVI
DC IN 12V
SYSTEM SELECT
IR SELECT 123
IN RS-232C OUT
DVI
DC IN 12V
SYSTEM SELECT
4
12
IR SELECT 123
IN RS-232C OUT
DVI
DC IN 12V
678
8 8
6
12
12 9
9
9
678
SYSTEM SELECT
678
DC IN 12V
First Camera
345
DVI
9
345
IN RS-232C OUT
6
345
IR SELECT 123
345
9
12
345
345
SYSTEM SELECT
9
678
CAUTION: the mains cable is used as a disconnecting device, use therefore an easily accessible outlet located near the device for the power supply connection. Never remove the mains plug while the device is connected.
12
12
DC IN 12V
6
Second Camera
9
9
Third Camera
678
6
Fourth Camera
678
9
First Camera
CAUTION: the mains cable is used as a disconnecting device, use therefore an easily accessible outlet located near the device for the power supply connection. Never remove the mains plug while the device is connected.
Second Camera
CAUTION: the mains cable is used as a disconnecting device, use therefore an easily accessible outlet located near the device for the power supply connection. Never remove the mains plug while the device is connected.
Third Camera
SYSTEM SELECT
IR SELECT 123
IN RS-232C OUT
DVI
8
8
8 7
678
5
7
345
9
12
7
7
DC IN 12V
SYSTEM SELECT
IR SELECT 123
IN RS-232C OUT
DVI
7 11
11 5
RS-232
RS-232 INPUT
10
2
INPUT
10
1
DVD/Blu-ray Player
4
OUTPUT
3
1
1
Media Player
Avaya Scopia XT Camera switch
3
Avaya Scopia XT Camera switch
3
2
connect cable 2 to USB2 (upper USB connector)
XT Camera Switch unit
Avaya Optional – Not Included Accessories*: Optional Camera
USB-USB cable
VISCA cross cable
HDMI-HDMI Cable
DVI – HDMI Cable Power supply
Avaya Accessories Included in Avaya Scopia XT5000/XT7000 box: First Camera Triple Cable
2
connect cable 2 to USB2 (upper USB connector)
Avaya Scopia XT5000 Codec Unit
Package Content:
1
Avaya Scopia XT7000 Codec Unit
* All cables needed for video, power and control are available separately when purchasing optional camera (Premium or Advanced). ** Note: The Codec Unit is HDCP compliant, but media will not be displayed for legal reasons.
CAUTION: Make sure all units are switched off whenever connecting or disconnecting devices.
*** If multiple cameras are cascaded using VISCA daisy chain, all must be the same model (all Premium Cameras or all Advanced Cameras). Cascading different camera models with VISCA daisy chain may yield wrong camera behavior.
Non-Avaya: Media player or Blu-ray device** HDMI-HDMI cable.
© 2000-2015 Avaya Inc. All intellectual property rights in this publication are owned by Avaya Inc. and are protected by United States copyright laws, other applicable copyright laws and international treaty provisions. Avaya Inc. retains all rights not expressly granted.All product and company names herein may be trademarks of their registered owners. This publication is Avaya Inc. Confidential & Proprietary. Use pursuant to your signed agreement or Avaya policy. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Avaya Inc. No representation of warranties for fitness for any purpose other than what is specifically mentioned in this guide is made either by Avaya Inc. or its agents. Avaya Inc. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. Avaya Inc may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to locate a copy, please contact Avaya Inc and a copy will be provided to you. Unless otherwise indicated, Avaya registered trademarks are registered in the United States and other territories. All registered trademarks recognized. For further information contact Avaya or your local distributor or reseller. Quick Setup Guide for Avaya Scopia® XT Camera Switch Version 8.3, March, 2015. http://www.avaya.com
rev. A02
Media Player
2
62111-02025
OUTPUT
3
P/N
DVD/Blu-ray Player
4
