AKRON® STREAMLINE STANDARD EUROPA CONTINENTAL Models 2132A, 2132B, 2132C, 2142A, 2142B, 2142C
AKRON® STREAMLINE EUROPA CONTINENTAL WITH DRAINAGE FACILITY Models 2152A, 2152B, 2152C, 2162A, 2162B, 2162C
SERVICE MANUAL SM ENGLISH 794-062-02
General Maintenance including Gas Strut It is recommended that the following checks and adjustments are carried out at minimum of twice a year and more frequently if the couch is in constant use. 1.
The framework of the couch is of steel construction and coated with an epoxy paint finish. This is resistant to most cleaning substances.
2.
The major pivot points need to be lubricated sparingly with oil. Care should be taken to keep oil away from the upholstery.
3.
All nuts should be checked and tightened where necessary Care should be taken not to over tighten the nuts on the pivot points as this may cause them to bind.
4.
Air tubes should be checked to ensure that they are not pinched.
5.
Disconnect the mains supply and check the following; Note: - all electrical should be carried out by a suitably qualified person. Electric cables and mains plug should be inspected for damage and replaced where necessary. In addition, electrical safety checks for earth continuity (class I equipment only) and earth leakage checks should also be carried out. The correct value fuse of 5 amps and ASTA approved to BS1362 MUST be used.
6.
The upholstered top is manufactured using fire retardant vinyl. This tends to go brittle if oil or grease (including body oils) are left on it. The upholstery should be cleaned with warm soapy water after use. The use of detergents is not recommended although a suitable sterilisation fluid is acceptable. Use of a couch cover or towel will help prolong the life of the upholstery.
7.
Woodscrews, used to secure the upholstery, should be checked and tightened or replaced where necessary.
8.
The hinge pins on the head and foot sections should be checked to ensure that they have not moved within the hinge tubes. Ensure Circlip is located fully in groove in pin. If the Circlip is not located correctly push firmly into groove to secure pin.
9.
Gas strut controls should be checked for a small amount of clearance between the operating flap and the release pin, throughout the range of movement. Should clearance be inadequate, or the top sinks whilst in use, the following adjustments should be made; firmly grasp the body of the strut and rotate in an anti-clockwise direction. Check for clearance and repeat as necessary. Should the gas strut fail to operate, refer to the above adjustment but rotate in a clockwise direction.
1
Manufacturers Details Huntleigh Healthcare Akron Products Division 1 Farthing Road Ipswich Suffolk IP1 5AP England Tel: Fax:
(0) 1473 461042 (0) 1473 462924
Huntleigh Healthcare, Akron Products Division A Member of the Huntleigh Technology PLC Group of Companies © Huntleigh Technology PLC 2007.
Register of Drawings/Revision History
DCN Number
1265 1235
Updated Drawings
Current Issue Status of Drawing
2R11218Z 2R11104Z -
2 2 -
2
Current Revision of Service Manual
Date
2
15/01/08
1
28/06/07
ITEM QTY 1 1 2 2 3 2 4 1 5 1 6 2 7 4 8 4 4 9 10 4 11 4 12 4 13 1 14 4 15 4 16 4 17 12 18 4 19 4 20 8 21 4 22 4 23 1 24 5 25 1 26 16 27 16 28 4 29 4 30 4 31 1 32 2
THE FRONT AND REAR ACTUATOR MOUNTS 3A10004P (4) AND 3A10005P (5) AND RELATED FIXINGS ARE TO BE LOOSELY ATTACHED TO THE BASE. THESE BRACKETS WILL THEN BE CORRECTLY POSITIONED AND SECURED IN THE CORRECT ORIENTATION DURING THE CREATION OF THE TOP LEVEL PRODUCT
26 26
26
2 26
27 27 18
4
2 28 27
30
26 22
29
11
27 27 27 31
26
26
27
24 20
26
17
12
27
10 19
17
27
26
32
7
26
27
6 17
10
18
20 7 30
14
26
26
1
14
17
11 21
23
11
26
26 27
17
12
19
12
27
10
26
20
14
17
29
30
18
10 29
13
15
8 21
25
9
20 3 32
17
12
20
14 24
24
28
16
5 11
17
20 17
30
19
15
29
3
19
21
18
17
7
Gary Cherrington
8
Digitally signed by Gary Cherrington DN: CN = Gary Cherrington, C = GB, O = Technical Manager Reason: I am approving this document Date: 2007.04.20 12:23:15 +01'00'
7
22
6
16
15
8
SHEET 1 OF 2
9
28
20 21
24
C 16
UNCONTROLLED WHEN PRINTED
22
24
15 20
ISSUE No. DESCRIPTION 2 Retractable Base Frame 0 H Section 1 H Section Link 0 Front Actuator Mounting Bracket 0 Rear Actuator Mount 0 Wheel Cam 1 Wheel Plunger 0 3" Castor 0 M10x20 Socket Head Set screw 0 M10x100mm Hex Bolt 0 3/4 Grey End Cap 0 3/4 Open Starlock 0 M10 Half Nut 0 M10 Benton Lock Nut Z/P 0 M10 Nyloc Nut 0 M10 Spring Washer 0 M10 Washer Flat Form B 0 1/4"x1" Seloc Pin 0 1700x19 Spring Ring 0 M10 White Nut Cap 0 1 1/2"x3/4"x16G Grey Insert 0 40x40 Moulded End Cap 0 40x40x2.5mm Insert 0 40x40x2.5 Grey Insert 0 10mm Foot Adjustment Stud 0 50x25x2.5 Grey Insert 0 Bronze Flanged Bush 1 Nylon Foot Rubber 0 Pedal Rubber 1 Pedal Sticker 0 Akron Products Division Label 0 Streamline 225 Product Label
17
17
28
PART No. 3A10001P 3A10002P 3A10003P 3A10004P 3A10005P 3A10006R 3A10007Z 5H0402A 5J8058R 5J8074A 5L0707L 5L0906Z 5L3319A 5L3319B 5L3319C 5L3351K 5L3362K 5M0408C 5M4296S 5N0057X 5N1107E 5N3737M 5N3737V 5N3744Z 5N3782U 5N3944Z 5P8000Z 5T0028Z 5T3200Z 5U1066Z 5U1109Z 5U1113Z
9
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
G Mullenger
CAD NO
2R11001Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 13/03/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Streamline Retractable Base
Patient Posit ioning Solutions
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS ISSUE
1
2
3
DATE
3/06 1/07 4/07
DCN
1198 1234 1243
ASSEMBLY
2R11001Z
ISSUE
3
ITEM QTY 1 1 2 2 3 2 4 1 5 1 6 2 7 4 8 4 4 9 10 4 11 4 12 4 13 1 14 4 15 4 16 4 17 12 18 4 19 4 20 8 21 4 22 4 23 1 24 5 25 1 26 16 27 16 28 4 29 4 30 4 31 1 32 2
27
UNCONTROLLED WHEN PRINTED
12
10
12 20
11
20
14
11
14 2
27
27
27
10
UPPER CROSS SECTION A-A
2
2 1
20
15
3
27
4
20
3
27
27
27
15
LOWER CROSS SECTION B-B STREAMLINE LIFTING MECHANISM
2 1
REFER TO UPPER H FRAME CROSS SECTION A-A 2
IT IS IMPORTANT TO ENSURE THAT THE INSERT (25) IS POSITIONED CORRECTLY IN THE BASE FRAME. IF THIS IS NOT DONE CORRECTLY THE MECHANISM WILL NOT OPERATE
PART No. 3A10001P 3A10002P 3A10003P 3A10004P 3A10005P 3A10006R 3A10007Z 5H0402A 5J8058R 5J8074A 5L0707L 5L0906Z 5L3319A 5L3319B 5L3319C 5L3351K 5L3362K 5M0408C 5M4296S 5N0057X 5N1107E 5N3737M 5N3737V 5N3744Z 5N3782U 5N3944Z 5P8000Z 5T0028Z 5T3200Z 5U1066Z 5U1109Z 5U1113Z
ISSUE No. DESCRIPTION 2 Retractable Base Frame 0 H Section 1 H Section Link 0 Front Actuator Mounting Bracket 0 Rear Actuator Mount 0 Wheel Cam 1 Wheel Plunger 0 3" Castor 0 M10x20 Socket Head Set screw 0 M10x100mm Hex Bolt 0 3/4 Grey End Cap 0 3/4 Open Starlock 0 M10 Half Nut 0 M10 Benton Lock Nut Z/P 0 M10 Nyloc Nut 0 M10 Spring Washer 0 M10 Washer Flat Form B 0 1/4"x1" Seloc Pin 0 1700x19 Spring Ring 0 M10 White Nut Cap 0 1 1/2"x3/4"x16G Grey Insert 0 40x40 Moulded End Cap 0 40x40x2.5mm Insert 0 40x40x2.5 Grey Insert 0 10mm Foot Adjustment Stud 0 50x25x2.5 Grey Insert 0 Bronze Flanged Bush 1 Nylon Foot Rubber 0 Pedal Rubber 1 Pedal Sticker 0 Akron Products Division Label 0 Streamline 225 Product Label
29 28
28 18
6
7
22
3
19
19 29 28
29
8
7 22 6
IMPORTANT WHEN FITTING LINK BARS 3A10003P ENSURE THAT THE THREE HOLES ARE POSITIONED AWAY FROM THE RAM END OF THE BASE FRAME REFER TO LOWER LINK BAR CROSS SECTION B-B
SHEET 2 OF 2
7
8
STREAMLINE RETRACTABLE PEDAL MECHANISM
8
19
Gary Cherrington C
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
G Mullenger
CAD NO
2R11001Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 13/03/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Streamline Retractable Base
Digitally signed by Gary Cherrington DN: CN = Gary Cherrington, C = GB, O = Technical Manager Reason: I am approving this document Date: 2007.04.20 12:23:27 +01'00'
Patient Posit ioning Solutions
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS ISSUE
1
2
3
DATE
3/06 1/07 4/07
DCN
1198 1234 1243
ASSEMBLY
2R11001Z
ISSUE
3
ITEM QTY 1 1 2 1 3 1 4 1 5 2 6 1 7 1 8 2 9 2 10 1
19
UNCONTROLLED WHEN PRINTED
29
11 19 8
2
18 7 30
9
14
28
28
25 14
ISSUE No. 7 3 3 3 1 0 1 2 1 1
DESCRIPTION Powered/Manual Mid Frame Left Hand Split Leg Frame Right Hand Split Leg Frame Follow Frame with Gas Strut Mount Short Upholstery Support Right Hand Operating Lever Right Hand Operating Lever Foot Rest Following Bar Foot Rest Trunnion 10x585 Hinge Pin
29
25 15
4
5
24
6 30
19
PART No. 3A01002P 3A01003P 3A01004P 3A01005P 3A01006P 3A01007P 3A01008P 3A01009Z 3A01010Z 3A01012Z
18
17
9
11
18 25
8
19
23
25
18
23 15
30
23
1 26
22
30
29
17 10
23
29
27
26
18
20
23
30
18
18
18
3
30
29
21
29
18
Follow Bar Securing Pin Streamline Europa Continential Top Frame 10x150 Hinge Pin Cover 200N Locking Gas Strut M10x55mm Hex Bolt M12x60mm Hex Bolt M6x40 Pan Head Set Screw 5/8 Capped Starlock M10 Nyloc Nut M10 Washer Flat Form B M12 Nyloc Nut M12 Washer Flat Form B 1/4"x1 3/4" Seloc Pin R Clip 8mm E Clip M10 White Nut Cap 3/8 End Cap 1"x1"x14G Insert 50x25x2.5 Grey Insert Bronze Flanged Bush DESCRIPTION
31
16 12
1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ISSUE No.
18
21
5
24
3A01013Z 3A10060P 3A01011Z 501-22 5G2800Z 5J8065A 5J8266A 5K1241U 5L0303Z 5L3319C 5L3362K 5L3519C 5L3562K 5M0414A 5M0800R 5M3145S 5N0057X 5N0300L 5N0948Z 5N3944Z 5P8000Z PART No.
13
23
29
11 2 12 1 13 2 14 2 15 2 16 4 17 2 18 12 4 19 20 4 21 8 22 2 23 6 24 2 25 4 26 3 27 4 28 2 29 8 30 8 31 4 ITEM QTY
18
18
16 21 31 21 27
16 29
26
20
31 13 30
21
30 21
31
20
21
27
16
27 20 21
C
SHEET 1 OF 2
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11104Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 11/06/2007 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Positioning Solutions
1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com
Streamline Europa Continential Top Assembly
REVISION STATUS
1
ISSUE
2
DATE
6/07 11/07
DCN
1235 1265
ASSEMBLY
2R11104Z
ISSUE
2
ITEM QTY 1 1 2 1 3 1 4 1 5 2 6 1 7 1 8 2 9 2 10 1 11 2 12 1 13 2 14 2 15 2 16 4 17 2 18 12 4 19 20 4 21 8 22 2 23 6 24 2 25 4 26 3 27 4 28 2 29 8 30 8 31 4
PART No. 3A01002P 3A01003P 3A01004P 3A01005P 3A01006P 3A01007P 3A01008P 3A01009Z 3A01010Z 3A01012Z 3A01013Z 3A10060P 3A01011Z 501-22 5G2800Z 5J8065A 5J8266A 5K1241U 5L0303Z 5L3319C 5L3362K 5L3519C 5L3562K 5M0414A 5M0800R 5M3145S 5N0057X 5N0300L 5N0948Z 5N3944Z 5P8000Z
ISSUE No. 7 3 3 3 1 0 1 2 1 1 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DESCRIPTION Powered/Manual Mid Frame Left Hand Split Leg Frame Right Hand Split Leg Frame Follow Frame with Gas Strut Mount Short Upholstery Support Right Hand Operating Lever Right Hand Operating Lever Foot Rest Following Bar Foot Rest Trunnion 10x585 Hinge Pin Follow Bar Securing Pin Streamline Europa Continential Top Frame 10x150 Hinge Pin Cover 200N Locking Gas Strut M10x55mm Hex Bolt M12x60mm Hex Bolt M6x40 Pan Head Set Screw 5/8 Capped Starlock M10 Nyloc Nut M10 Washer Flat Form B M12 Nyloc Nut M12 Washer Flat Form B 1/4"x1 3/4" Seloc Pin R Clip 8mm E Clip M10 White Nut Cap 3/8 End Cap 1"x1"x14G Insert 50x25x2.5 Grey Insert Bronze Flanged Bush
SHEET 2 OF 2
12
16
16 27
27 20
20
31
31
FRONT CONTINENTIAL FIXING MECHANISM
12
12
27
27 16
20
16
20 31
31
FRONT CONTINENTIAL FIXING MECHANISM
REAR CONTINENTIAL FIXING MECHANISM
REAR CONTINENTIAL FIXING MECHASNISM C
UNCONTROLLED WHEN PRINTED
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11104Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 11/06/2007 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Positioning Solutions
1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com
Streamline Europa Continential Top Assembly
REVISION STATUS
1
ISSUE
2
DATE
6/07 11/07
DCN
1235 1265
ASSEMBLY
2R11104Z
ISSUE
2
ITEM QTY 1 1 2 2 3 1 4 1 5 1 6 2 7 1 8 4 4 9 10 2 11 2 12 1 13 2 14 6 15 4 16 2 17 1 18 2 19 1
18
1
6 9 19
9 3
10
11 16
PART No. 3A03245P 3A03249Z 3A03264P 3A09040Z 5G2200Z 5J7665A 5J8266A 5K1241U 5L0362V 5L0803Z 5L2919C 5L3519C 5L3562K 5L3577X 5M3145S 5N0055X 5N0058X 5N0300L 5N2100M
ISSUE No. DESCRIPTION 0 Release Bar Assembly 0 Double Grooved Hinge Pin (10x84) 1 A Head Frame 0 Trunnion 0 200N Locking Gas Strut 0 M6x55 Bolt Hex Ht 0 M12x60mm Hex Bolt 0 M6x40 Pan Head Set Screw 0 1/4 Flat Washer 0 5/8 Capped Starlock 0 M6 Nyloc Nut 0 M12 Nyloc Nut 0 M12 Washer Flat Form B 0 M12 Nylon Washer 0 8mm E Clip 0 M6 White Nut Cap 0 M12 White Nut Cap 0 3/8 End Cap 0 8.5mm Grey Insert
4 8
10
5
18
15
8
2
8 15
7 15
13
8
14 13
14 14
12 15
14
2
14
UNCONTROLLED WHEN PRINTED
14 17
C
STREAMLINE CONNECTIONS
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2N10132Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 15/02/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
Streamline A Head Frame Assembly
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS ISSUE
1
2
DATE
4/06 1/07
DCN
1198 1234
ASSEMBLY
2N10132Z
ISSUE
2
ITEM QTY 1 1 2 2 3 1 4 1 5 1 6 2 7 1 8 4 4 9 10 2 11 2 12 1 13 2 14 6 15 4 16 2 17 1 18 2 19 1
18
1
6 9 19
PART No. 3A03245P 3A03249Z 3A03265P 3A09040Z 5G2000Z 5J7665A 5J8266A 5K1241U 5L0362V 5L0803Z 5L2919C 5L3519C 5L3562K 5L3577X 5M3145S 5N0055X 5N0058X 5N0300L 5N2100M
ISSUE No. DESCRIPTION 0 Release Bar Assembly 0 Double Grooved Hinge Pin (10x84) 1 B Head Frame 0 Trunnion 0 270N Locking Gas Strut 0 M6x55 Bolt Hex Ht 0 M12x60mm Hex Bolt 0 M6x40 Pan Head Set Screw 0 1/4 Flat Washer 0 5/8 Capped Starlock 0 M6 Nyloc Nut 0 M12 Nyloc Nut 0 M12 Washer Flat Form B 0 M12 Nylon Washer 0 8mm E Clip 0 M6 White Nut Cap 0 M12 White Nut Cap 0 3/8 End Cap 0 8.5mm Grey Insert
3 9 10
11 16
4
8
10
15 5
2
8 15
18 8
7 15
13
8
14 13
14 14
12 15
14
2 14 14 17
UNCONTROLLED WHEN PRINTED
C
STREAMLINE CONNECTIONS
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2N10133Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 15/02/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
Streamline B Head Frame Assembly
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS ISSUE
1
2
DATE
4/06 1/07
DCN
1198 1234
ASSEMBLY
2N10133Z
ISSUE
2
ITEM QTY 1 1 2 2 3 1 4 2 5 1 6 1 7 1 8 1 9 2 10 4 11 2 12 1 13 2 14 8 15 4 16 2 17 2 18 6 19 1 20 2 21 6 22 4 23 2 24 1 25 2 26 6 27 1 28 4
12 26
20 22
21 21
6
21
2
21
14
21
STREAMLINE CONNECTIONS 26
8
18 18
9
21
10
20
14 22
4
19 24
10
14 22
28
28
16
PART No. 3A03244P 3A03249Z 3A09040Z 3A09062R 3A10028P 3A10029P 3A10030P 5G2000Z 5G7000Z 5J7663A 5J7665A 5J8266A 5K1136T 5K1241U 5L0362V 5L0803Z 5L2819C 5L2919C 5L3519C 5L3562K 5L3577X 5M3145S 5N0055X 5N0058X 5N0300L 5N0909E 5N2100M 5T2800Z
ISSUE No. 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DESCRIPTION T Bar Release Lever Double Grooved Hinge Pin (10x84) Trunnion Nylon Plunger Right Hand Arm Support Left Hand Arm Support Streamline C Head Frame 270N Locking Gas Strut 11.25 x 29.5 x 1.25 Spring M6x45 Bolt Hex Ht M6x55 Bolt Hex Ht M12x60mm Hex Bolt M5x15 Pan Head Set Screw M6x40 Pan Head Set Screw 1/4 Flat Washer 5/8 Capped Starlock M5 Nyloc Nut M6 Nyloc Nut M12 Nyloc Nut M12 Washer Flat Form B M12 Nylon Washer 8mm E Clip M6 White Nut Cap M12 White Nut Cap 3/8 End Cap 1 x1 x 16G Insert 8.5mm Grey Insert Self Adhesive Film (0.01)
7 3
2
14 16
14
27
22
4 18 14
26
18
17
9 13
11
10
15 11
26
25
13
14
17
15 18
15
28
28
10
23
UNCONTROLLED WHEN PRINTED 14
26
1 15
23 25
18
26
C
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
2N10135Z CAD NO THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 06/04/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Positioning Solutions
Streamline Suspa C Head Frame Assembly
1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com
REVISION STATUS ISSUE
1
DATE
03/07
DCN
1239
ASSEMBLY
2N10135Z
ISSUE
1
HANNING 230V 2
3A10004P FRONT ACTUATOR MOUNTING BARCKET
9
3A10005P REAR ACTUATOR MOUNTING BRACKET 6 2
7
5
5
2
2
10
5
5
5
1
4 8
7
5
3
4
10 5
5 4
8 8
4 11
14
8
12 11 12
9 6 7
UNCONTROLLED WHEN PRINTED
2Z1100Z HANNING MAINS CABLE AND RAM PLUG RUBBER
13
7
3 14 1 13 1 12 2 11 2 10 2 9 2 8 6 7 4 6 2 5 12 4 6 3 2 2 6 1 1 ITEM QTY
S6243 5S0326Z 5S0315Z 5S0307Z 5N2100M 5N0058X 5N0056X 5L3562K 5L3519C 5L3162K 5L3119C 5J8264A 5J7866A 5F0601Z PART No.
0 0 0 0 0 0 0 0 0 0 0 0 0 0 ISSUE No.
Cable Gland (Bell End Split) Curly Wrap RS227-974 Cable Tie RS543-428 Cable Tie Base RS227-996 8.5mm Grey Insert M12 White Nut Cap M8 White Nut Cap M12 Washer Flat Form B M12 Nyloc Nut M8 Washer Flat Form B M8 Nyloc Nut M12x50mm Hex Bolt M8x60 Hex Ht Bolt 230v Hanning Ram (Type V) DESCRIPTION
SHEET 1 OF 2 C
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11202Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 06/09/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
230v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 1/07
DCN
1198 1234
ASSEMBLY
2R11202Z
ISSUE
2
HANNING 230V
IMPORTANT. ENSURE THAT THE REAR ACTUATOR MOUNT 3A10004P ATTACHED TO THE BASE FRAME IS INSTALLED IN THE CORRECT UPPER POSITION AND ORIENTATION FOR INSTALLATION OF HANNING RAM
ENSURE MAINS LEAD PASSES THROUGH AND IS SECURED BY THE CABLE GLAND TO REMOVE ANY STRAIN RELIEF ON THE MAINS CABLE ENSURE CURLY WRAP IS POSITIONED HIGH ENOUGH TO CLEAR THE LINK BARS WHEN IN OPERATION
ALL ACTUATOR RAM BRACKETS WILL BE REFERENCED TO THE RETRACTABLE AND LARGE WHEEL BASE ASSEMBLIES TO WHICH THESE PARTS WILL BE ATTACHED.
ENSURE HANNING AIR PIPE TO HAND/FOOTSWITCH IS SECURED AND FOLLOWS THE MAINS LEAD THROUGH THE CURLY WRAP IMPORTANT. WHEN REPLACING OR INSTALLING THE ACTUATOR ENSURE THAT THE ROD END OF THE RAM IS BOLTED TO THE MOUNTING BRACKET 3A10004P BEFORE THE BRACKET IS RAISED INTO POSITION AND SECURED TO THE UNDERSIDE OF THE LINK BARS.
IMPORTANT. ENSURE THAT THE FRONT ACTUATOR MOUNT ATTACHED TO THE BASE ASSEMBLY IS POSITIONED IN THE FIRST TWO HOLES TOWARDS THE PUMP END OF THE BASE TO ENSURE CORRECT STROKE IS ACHIEVED ON THE ACTUATOR
IMPORTANT ENSURE THAT THE HANNING RAM IS INSTALLED TO THE RIGHT HAND PLATE OF THE REAR ACTUATOR MOUNTING BRACKET
UNCONTROLLED WHEN PRINTED
C
SHEET 2 OF 2
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11202Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 06/09/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
230v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 1/07
DCN
1198 1234
ASSEMBLY
2R11202Z
ISSUE
2
HANNING 115V 2
3A10004P FRONT ACTUATOR MOUNTING BARCKET
9
3A10005P REAR ACTUATOR MOUNTING BRACKET 6 2
7
5
5
2
2
10
5
5
5
1
4 8
7
5
3
4
10 5
5 4
8 8
4 11
14
8
12 11 12
9 6 7
UNCONTROLLED WHEN PRINTED
2Z1100Z HANNING MAINS CABLE AND RAM PLUG RUBBER
13
7
3 14 1 13 1 12 2 11 2 10 2 9 2 8 6 7 4 6 2 5 12 4 6 3 2 2 6 1 1 ITEM QTY
S6243 5S0326Z 5S0315Z 5S0307Z 5N2100M 5N0058X 5N0056X 5L3562K 5L3519C 5L3162K 5L3119C 5J8264A 5J7866A 5F0502Z PART No.
0 0 0 0 0 0 0 0 0 0 0 0 0 0 ISSUE No.
Cable Gland (Bell End Split) Curly Wrap RS227-974 Cable Tie RS543-428 Cable Tie Base RS227-996 8.5mm Grey Insert M12 White Nut Cap M8 White Nut Cap M12 Washer Flat Form B M12 Nyloc Nut M8 Washer Flat Form B M8 Nyloc Nut M12x50mm Hex Bolt M8x60 Hex Ht Bolt 115v Hanning Ram (Type V) DESCRIPTION
SHEET 1 OF 2 C
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11203Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 06/09/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
115v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 01/07
DCN
1198 1234
ASSEMBLY
2R11203Z
ISSUE
2
HANNING 115V
IMPORTANT. ENSURE THAT THE REAR ACTUATOR MOUNT 3A10004P ATTACHED TO THE BASE FRAME IS INSTALLED IN THE CORRECT UPPER POSITION AND ORIENTATION FOR INSTALLATION OF HANNING RAM
ENSURE MAINS LEAD PASSES THROUGH AND IS SECURED BY THE CABLE GLAND TO REMOVE ANY STRAIN RELIEF ON THE MAINS CABLE ENSURE CURLY WRAP IS POSITIONED HIGH ENOUGH TO CLEAR THE LINK BARS WHEN IN OPERATION
ALL ACTUATOR RAM BRACKETS WILL BE REFERENCED TO THE RETRACTABLE AND LARGE WHEEL BASE ASSEMBLIES TO WHICH THESE PARTS WILL BE ATTACHED.
ENSURE HANNING AIR PIPE TO HAND/FOOTSWITCH IS SECURED AND FOLLOWS THE MAINS LEAD THROUGH THE CURLY WRAP IMPORTANT. WHEN REPLACING OR INSTALLING THE ACTUATOR ENSURE THAT THE ROD END OF THE RAM IS BOLTED TO THE MOUNTING BRACKET 3A10004P BEFORE THE BRACKET IS RAISED INTO POSITION AND SECURED TO THE UNDERSIDE OF THE LINK BARS.
IMPORTANT. ENSURE THAT THE FRONT ACTUATOR MOUNT ATTACHED TO THE BASE ASSEMBLY IS POSITIONED IN THE FIRST TWO HOLES TOWARDS THE PUMP END OF THE BASE TO ENSURE CORRECT STROKE IS ACHIEVED ON THE ACTUATOR
IMPORTANT ENSURE THAT THE HANNING RAM IS INSTALLED TO THE RIGHT HAND PLATE OF THE REAR ACTUATOR MOUNTING BRACKET
UNCONTROLLED WHEN PRINTED
C
SHEET 2 OF 2
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11203Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 06/09/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
115v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 01/07
DCN
1198 1234
ASSEMBLY
2R11203Z
ISSUE
2
HANNING 100V 2
3A10004P FRONT ACTUATOR MOUNTING BARCKET
9
3A10005P REAR ACTUATOR MOUNTING BRACKET 6 2
7
5
5
2
2
10
5
5
5
1
4 8
7
5
3
4
10 5
5 4
8 8
4 11
14
8
12 11 12
9 6 7
UNCONTROLLED WHEN PRINTED
2Z1100Z HANNING MAINS CABLE AND RAM PLUG RUBBER
13
7
3 14 1 13 1 12 2 11 2 10 2 9 2 8 6 7 4 6 2 5 12 4 6 3 2 2 6 1 1 ITEM QTY
S6243 5S0326Z 5S0315Z 5S0307Z 5N2100M 5N0058X 5N0056X 5L3562K 5L3519C 5L3162K 5L3119C 5J8264A 5J7866A 5F1211Z PART No.
0 0 0 0 0 0 0 0 0 0 0 0 0 0 ISSUE No.
Cable Gland (Bell End Split) Curly Wrap RS227-974 Cable Tie RS543-428 Cable Tie Base RS227-996 8.5mm Grey Insert M12 White Nut Cap M8 White Nut Cap M12 Washer Flat Form B M12 Nyloc Nut M8 Washer Flat Form B M8 Nyloc Nut M12x50mm Hex Bolt M8x60 Hex Ht Bolt 100v Hanning Ram (Type V) DESCRIPTION
SHEET 1 OF 2 C
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11212Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 06/09/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
100v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 01/07
DCN
1198 1234
ASSEMBLY
2R11212Z
ISSUE
2
HANNING 100V
IMPORTANT. ENSURE THAT THE REAR ACTUATOR MOUNT 3A10004P ATTACHED TO THE BASE FRAME IS INSTALLED IN THE CORRECT UPPER POSITION AND ORIENTATION FOR INSTALLATION OF HANNING RAM
ENSURE MAINS LEAD PASSES THROUGH AND IS SECURED BY THE CABLE GLAND TO REMOVE ANY STRAIN RELIEF ON THE MAINS CABLE ENSURE CURLY WRAP IS POSITIONED HIGH ENOUGH TO CLEAR THE LINK BARS WHEN IN OPERATION
ALL ACTUATOR RAM BRACKETS WILL BE REFERENCED TO THE RETRACTABLE AND LARGE WHEEL BASE ASSEMBLIES TO WHICH THESE PARTS WILL BE ATTACHED.
ENSURE HANNING AIR PIPE TO HAND/FOOTSWITCH IS SECURED AND FOLLOWS THE MAINS LEAD THROUGH THE CURLY WRAP IMPORTANT. WHEN REPLACING OR INSTALLING THE ACTUATOR ENSURE THAT THE ROD END OF THE RAM IS BOLTED TO THE MOUNTING BRACKET 3A10004P BEFORE THE BRACKET IS RAISED INTO POSITION AND SECURED TO THE UNDERSIDE OF THE LINK BARS.
IMPORTANT. ENSURE THAT THE FRONT ACTUATOR MOUNT ATTACHED TO THE BASE ASSEMBLY IS POSITIONED IN THE FIRST TWO HOLES TOWARDS THE PUMP END OF THE BASE TO ENSURE CORRECT STROKE IS ACHIEVED ON THE ACTUATOR
IMPORTANT ENSURE THAT THE HANNING RAM IS INSTALLED TO THE RIGHT HAND PLATE OF THE REAR ACTUATOR MOUNTING BRACKET
UNCONTROLLED WHEN PRINTED
C
SHEET 2 OF 2
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11212Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 06/09/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
100v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 01/07
DCN
1198 1234
ASSEMBLY
2R11212Z
ISSUE
2
ITEM QTY 1 1 2 3 3 6 4 1
PART No. 2Z5000Z 5K0304R 5L2755K 5U1121Z
ISSUE No. DESCRIPTION 1 A1048 Streamline UL Junction Box 0 No.8 x 5/16 PH Self-Tap 0 4mm Sakeproof Washer 0 Earth Label
1
45 1
(46) 3 HOLES DRILLED n3.7 THRO ONE FACE ONLY
20
3 3
4
2
3 3
3
2
3 2 1
C
UNCONTROLLED WHEN PRINTED
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11210Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 11/08/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
Streamline Junction Box Positioning
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS ISSUE
1
DATE
1/07
DCN
1198
ASSEMBLY
2R11210Z
ISSUE
1
ITEM QTY 1 2 2 1 3 2 4 1 5 1 6 2 7 1 8 1 9 2 10 4 11 2 12 2 13 4 14 4 15 8 16 4 17 4 18 1 19 6
PART No. 3A00230Z 3A00231P 3A00232P 3A10020P 3A10021P 5F2100Z 5F7000Z 5F7200Z 5G6000Z 5J7653Z 5J7855Z 5J7859N 5L3119B 5L3119C 5L3162K 5N0056X 5N9208M 5T0047Z 5U1095Z
ISSUE No. 0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DESCRIPTION Adjusting Stud FBS Mechanism Holder Assembly Sleeve Pivot Mount Bracket RH Streamline FBS Push/Pull Bar LH Streamline FBS Push/Pull Bar Hanning Single Handswitch Hanning Round Air Pipe (0.7M) Air Tube Connector Mechanism Spring M6x6 Grub Screw M8x10 Grub Screw M8x25 Hex Ht Bolt M8 Full Nut M8 Nyloc Nut M8 Washer Flat Form B M8 White Nut Cap 7/8 x 16G Round Insert FBS Mechanism Guard Raise/Lower Self Adhesive Sticker
UNCONTROLLED WHEN PRINTED 17
19
16 14
15
11
15
3
16
14
15 3
15
19
19
15
12
17
15 12 11 5
REFER TO RAM KITS FOR CURLY WRAP SPECIFICATION
19 13 9 1
19 13 13
7
1
17
13
10
8 4
9 6 19 15
10
14 16
10 6
2
SHEET 1 OF 2
10 18 17 14 16
15
C
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11208Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 09/08/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
A1047 Streamline Foot Bar Switch Assembly
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
08/06 1/07
DCN
1198 1234
ASSEMBLY
2R11208Z
ISSUE
2
9
13
1
13
1
ITEM QTY 1 2 2 1 3 2 4 1 5 1 6 2 7 1 8 1 9 2 10 4 11 2 12 2 13 4 14 4 15 8 16 4 17 4 18 1 19 6
9
6
6
4
5
PART No. 3A00230Z 3A00231P 3A00232P 3A10020P 3A10021P 5F2100Z 5F7000Z 5F7200Z 5G6000Z 5J7653Z 5J7855Z 5J7859N 5L3119B 5L3119C 5L3162K 5N0056X 5N9208M 5T0047Z 5U1095Z
2
ISSUE No. DESCRIPTION 0 Adjusting Stud 1 FBS Mechanism Holder Assembly 0 Sleeve Pivot Mount Bracket 0 RH Streamline FBS Push/Pull Bar 0 LH Streamline FBS Push/Pull Bar 0 Hanning Single Handswitch 0 Hanning Round Air Pipe (0.7M) 0 Air Tube Connector 0 Mechanism Spring 0 M6x6 Grub Screw 0 M8x10 Grub Screw 0 M8x25 Hex Ht Bolt 0 M8 Full Nut 0 M8 Nyloc Nut 0 M8 Washer Flat Form B 0 M8 White Nut Cap 0 7/8 x 16G Round Insert 0 FBS Mechanism Guard 0 Raise/Lower Self Adhesive Sticker
UNCONTROLLED WHEN PRINTED
3 5 16 14 15 15 15 12
SHEET 2 OF 2 C
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11208Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 09/08/2006 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Posit ioning Solutions
A1047 Streamline Foot Bar Switch Assembly
1 FARTHI NG ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
08/06 1/07
DCN
1198 1234
ASSEMBLY
2R11208Z
ISSUE
2
ITEM QTY 1 1 2 1 3 1 4 2 5 5 6 2
PART No. 3A01014P 5J8260A 5J8261A 5L3519C 5L3562K 5N0058X
ISSUE No. 2 0 0 0 0 0
DESCRIPTION Streamline Europa Dummy Ram Plate M12x30mm Hex Bolt M12x35mm Hex Bolt M12 Nyloc Nut M12 Washer Flat Form B M12 White Nut Cap
UNCONTROLLED WHEN PRINTED
2 5 5
5
4 6
1
3
5
5 4 C 6
COPYRIGHT. HUNTLEIGH TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11218Z
THIS DRAWING IS NOT TO BE LOANED TO THIRD PARTIES OR USED WITHOUT DATE 13/06/2007 WRITTEN CONSENT OF HUNTLEIGH CHECKED & AKRON LIMITED APPROVED TITLE
Patient Positioning Solutions
Streamline Europa Dummy Ram Strap
1 FARTHING ROAD IPSWICH, SUFFOLK IP1 5AP. ENGLAND TEL: +44(0)1473 461042 FAX: +44(0)1473 462924 www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
6/07 12/07
DCN
1235 1265
ASSEMBLY
2R11218Z
ISSUE
2
