Congratulations on your purchase of the Xotic AC Plus! United with our widely acclaimed booster circuits and very versatile preamp. Both channels offer shimmering smooth tone with tons of sustain. Each channel delivers two distinct voicing modes that cover the entire range of gain structure. Activate both channel stacks with a single button for unlimited configurations of superb tone. Channel A Gain: Determines the amount of distortion of channel A
Volume: Controls overall level of channel A Tone: Attenuates midrange and treble frequencies.
Boost: Boosts bass and midrange frequencies +3dB Channel A on/off switch: True bypass, no loading down when the pedal is off
Volume: Controls overall level of channel B Comp: Allow you to switch between Soft or Hard clipping. Hard clipping (button down) offers early break up. Setting the gain knob past 3 o’clock delivers smooth overdrive. Soft clipping (button up) offers late break up and works well as a clean boost.
Channel B Gain: Determines the amount of clipping of channel B Three Band EQ: Allows you to shape the tone of Ch B to your desired sound. Treble: High shelving EQ @10KHz Mid: Peaking @1.2KHz Bass: Low shelving EQ @100Hz
*You may have difficulty hearing the difference when the gain is at lower setting
Channel B on/off switch: True bypass, no loading down when the pedal is off 1 of 2
A>B, B>A: Allow you to change the order of the signal through the effect Channel A to Channel B or Channel B to Channel A Button Down
Channel B
Channel A
Signal flow
Button Up
Channel A
Channel B
Signal flow
Sample Sound Settings: Texan Blues Tone
Brown Sound
Rhythm: B channel only Lead: A+B channel Input impedance: 1M ohm Output impedance: 1K ohm Max current draw: 15mA Dimensions: W4.62” D3.65” H2” Weight: 0.9 lbs Optional external power supply: 9 volt DC (regulated recommended) 2.1mm standard barrel with negative tip (center) such as Boss PSA, Ibanez, Dunlop Power brick, Voodoo Labs Power-all, 1-spot, etc
2 of 2
Xotic Effects USA 14920 Calvert Street Van Nuys, CA 91411 USA Phone/Fax: (818)367-9593 http://www.xoticeffects.com
... en maintenance comporte une gâche en plastique, celle-ci doit être remplacée par une gâche métallique et le joint d'étanchéité doit également être remplacé.
Transfer tech sheet (and bag) over to new single metal access panel. Place new panel on dishwasher and align holes in panel with holes in clips. 4. Secure single metal access panel to dishwasher using the. 2 screws supplied. 5. Replace all parts and
Siga el ajuste de la prueba de tensión de CA. 8. .... A menos que mida tensión o corriente, apague y bloquee el suministro ..... O.L. » en cas de polarisation.
Power on at circuit 1. 2. Power on at circuit 2. Figure 5. Positioning the Fixture: 5. After the light is on, rotate the luminaire's body horizontally or vertically to aim it ...
(2) This device must accept any interference received, including interference that may cause undesired .... Indicates a procedure that could result in serious injury or death to the user or other persons if ... Do not operate near people or roads.
causer un décès ou un choc électrique. Replacer pièces et ... S'assurer de déconnecter la source de courant électrique avant ... composant. FIGURE 1. AXE EN ...
bride mécanique de la tête de culasse après avoir amené le compresseur à pression atmosphérique, et vérifier les points suivants: • Contrôler que les canaux ...
for Strike Plate and Latch Assembly kit. 1. Unplug dishwasher or ... may not be designed to function with the new latch design in an optimal fashion that could ...
Dans le cas du remplacement de pièces individuelles ou d'une ...... bride mécanique de la tête de culasse après avoir ... Mettre le compresseur en pièces (fig. 5).