Fisher & Paykel Appliances Inc 5800 Skylab Road, Huntington Beach California CA92647, USA

Refrigeration

SERVICE SUMMARY Ice & Water

This information is intended for use by individuals possessing adequate experience in servicing electrical, electronic and mechanical appliances. Any attempt to repair a major appliance may result in personal injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use. Cette information est destinée aux personnes possédant l’expérience requise pour réparer des appareils électriques, électroniques et mécaniques. Toute tentative de réparation d’un gros appareil comporte un risque de blessures à personnes et de dommages matériels. Le fabricant et le revendeur ne peuvent en aucun cas être chargés de l’interprétation de cette information, ni assumer aucune responsabilité en rapport avec son utilisation.

CAUTION: This machine must be electrically grounded. It can be grounded through the grounding lead in the 3-prong power cord, if plugged into a properly grounded appliance outlet or through a separate No. 13 or large wire from the cabinet to an established ground. In all cases the grounding method must comply with any local electrical code requirements. Certain internal parts are internationally NOT GROUNDED and may present a risk of electrical shock only during servicing. To reduce the risk of shock, disconnect the power supply cord before servicing. CAUTION: ALL TERMINALS AND INTERNAL PARTS SHOULD BE TREATED AS LIVE. IMPORTANT – RE-CONNECT ALL GROUNDING DEVICES. If grounding wires, screws, straps, clips, nuts or washers used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened.

IMPORTANTES CONSIGNES DE SÉCURITÉ ATTENTION : Cette machine doit être mise à la terre. Elle peut l’être par le biais du conducteur de terre du cordon d’alimentation à prise de terre mâle, s’il est branché sur un point de réseau électrique correctement mis à la terre, ou par le biais d’un fil électrique épais séparé de l’appareil à la terre. Certaines pièces internes ne sont pas MISES A LA TERRE selon les normes internationales et peuvent présenter un risque d’électrocution durant l’entretien. Pour réduire le risque d’électrocution, le cordon d’alimentation doit être débranché avant tout entretien de l’appareil. ATTENTION : TOUTES COSSES DE CÂBLES ET PIÈCES INTERNES SONT À TRAITER COMME ÉTANT SOUS TENSION IMPORTANT – REBRANCHER TOUS LES DISPOSITIFS AVEC MISE À LA TERRE Si les conducteurs de terre, vis, barrettes, clips, écrous ou rondelles utilisés pour acheminer le circuit à la terre sont ôtés lors de l’entretien, ils doivent être solidement remis à leur place d’origine. Key Presses Temperature Settings Press the MENU button until the Temperature Icon is highlighted. The refrigerator Icon shall be highlighted as well. By pressing the UP or DOWN will change the temperature of the PC. By pressing the MENU button again the FC section of the refrigerator will be highlighted. By pressing the UP or DOWN button will change the temperature of the FC. The factory default setting are 34.7ºF PC and 0º F for the FC.

Input/Output Status

To enter input / output status: • Press and hold the MENU button, then press the UP button for 4 seconds. This enters Diagnostic mode. • Press the UP button three times. The current input /output status will be displayed. If a device is on or a door is open, the respective LCD will be on. Return to normal operation by pressing the MENU button. Note: Only the first 6 LCD’s are used. The last 5 are not used.

Temperature Settings

P/N 819444

- 1 -

A: Electronic / Electrical Faults

Ice & Water products have the LED display on the door. A wrench symbol and LCD fault code will appear automatically if there is a fault in the temperature measuring system, defrost system, fans or low ambient heater. Fault Codes A wrench symbol and LCD fault code will appear automatically if there is a fault in the temperature measuring system, defrost system, fans or low ambient heater. When the PC door is opened an alarm will sound, the number of beeps also indicates the fault code. Pressing any of the control buttons can deactivate these alarms

Fault Code 1 Reason: On last power up, the power module failed self test. Primary Action: Replace power module Fault Code 2 Reason: The previous 2 defrosts were aborted after 30 minutes Primary Action: Check defrost element Fault Code 3 Reason: The resistance of all the temperature sensors is outside the normal range (>45K Ohms) Primary Action: Check 6 –way Rast connector at power module Fault Code 4 Reason: The resistance of all the temperature sensors is outside the normal range (< 660 Ohms) Primary Action: Check 6 –way Rast connector at power module Fault Code 5 Reason: The resistance of the FC sensors is outside the normal range (>45K Ohms) Primary Action: Check sensor connector at power module Fault Code 6 Reason: The resistance of the FC sensors is outside the normal range (45K Ohms) Primary Action: Check sensor connector at power module Fault Code 8 Reason: The resistance of the Defrost sensor is outside the normal range (45K Ohms) Primary Action: Check sensor connector Fault Code 10 Reason: The resistance of the PC sensors is outside the normal range (