#61-025 VoltAware⢠Non-Contact Voltage (NCV)Tester
61-025 model indicates presence of voltage from 40-1000VAC. ⢠Visual indication of voltage. ⢠Selectable Audible indication of voltage. ⢠Low Battery Indicator.
IMPORTANT SAFETY INFORMATION Read and understand all of the instructions and safety information in these operating instructions before using this tester. WARNINGS To avoid possible electric shock, personal injury or death follow these guidelines: • Do not use if green light is not illuminating on tester. • Do not use if tester appears damaged or is not operating properly. • Do not use tester for more than the rated voltage on the tester. • Do not use without the tester fully assembled. • This tester will not detect the presence of DC voltage. • This tester will not detect voltages at a distance, such as through walls, metal conduit, or shielded wire. • Voltage detection maybe affected by outlet design, insulation thickness/type. • Do not assume that no voltage indication means the circuit is de-energized. • Voltages below 40VAC will not be detected by the 61-025 but are still shock hazards that can result in injury or death. • Use the 3 Point Safety Method. (1) Verify tester operation by measuring a known voltage. (2) Apply tester to circuit under test. (3) Return to the known live voltage again to ensure proper operation. • Ensure all fingers are behind finger guard when testing for voltage. • If this tester is used in a manner not specified by IDEAL, protection provided by the product may be impaired. • Comply with local and national safety requirements, including the use of appropriate personal protective equipment. Features: The VoltAware™ NCVtester is useful for identifying hot conductors, finding breaks in wires and detecting the presence of AC voltage at outlets, switches, electrical panels, wires and cables. • 61-025 model indicates presence of voltage from 40-1000VAC • Visual indication of voltage • Selectable Audible indication of voltage • Low Battery Indicator • Sleek, compact design Operation: • Twist the tester body to the On position. • Verify the green light is on. • Verify tester operation on a known voltage source. • Place the tip of the tester near an AC voltage source to obtain a voltage indication. • Voltage presence is indicated by a red, flashing light. Selectable On/Off for Audible Beeper: • The tester defaults to the audible ON mode. • To turn the audible Off, depress the dark gray button. • To turn the audible back On, depress the button again. Note: Tester must be in standby mode for button to activate circuitry. Low Battery Indicator: • When the battery voltage drops below 2V, the tester indicates the low battery condition by turning off the green light. Battery Replacement: • With the tester in the middle position, pull apart the two case halves. • Replace with 2 AAA (LR03) batteries. • Reverse process to re-assemble tester.
OFF
#61-025
40-1000VAC
ON
Maintenance: Clean with a damp cloth and mild detergent. If the tester acts erratically, or the green light is not on, change the batteries. Service and Replacement Parts: There are no user-serviceable parts. To inquire about service information, contact IDEAL INDUSTRIES, INC.at 877-201-9005, or visit our website at www.testersandmeters.com. Specifications: Voltage Range: Frequency Range: Operating Environment: Storage Temp.: Battery: Altitude: Dimensions: Weight: Safety
#61-025
Cat IV 40-1000VAC
OFF ON
40-1000VAC (61-025) 50-500 Hz 32 to 122°F (0 to 51°C) at
zero. Relays are electro-mechanical devices subject to ravages of age ... "drop out" thus resetting the over-volt- signed to be a voltage regulator, not an.
Application areas include transducer amplifier with pulse shaper, DC gain ... either TTL or CMOS logic. ... Lead Temperature (Soldering, 10 seconds). 260ËC.
Jan 20, 2011 - We discuss the influence of short-range electrostatic forces, ... atomic force microscope (AFM) and a surface carrying charged adatoms. Dipolar ...
Figure 23. High output current with short circuit protection . .... 23. Table 19. Electrical characteristics of L7812C . ...... Date. Revision. Changes. 21-Jun-2004. 12.
54. Table 33. Document revision history . ...... These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked ...
Load and line regulation are specified at constant junction temperature. Changes ... Pulse testing with low duty cycle is used. Symbol ... Dropout Voltage. IO =1A.
Output Voltage. Io = -5 mA to -1 A Po ⤠15 W. Vi = 8 to 20 V. -4.75. -5. -5.25. V. âVo*. Line Regulation. Vi = -7 to -25 V Tj = 25 oC. Vi = -8 to -12 V Tj = 25 oC. 100.
template on the inside lid of the box to cut a hole in the ceiling for the type of ... Should this product fail during the warranty period it will be replaced free of ...
Symbol. Conditions. Min. Typ. Max. Unit. Line Regulation. âVO. VI = 12V to 15V. VI = 12V to 40V. -. 0.01. 0.1. 0.1. 0.5. %. TMIN â¤TAâ¤TMAX. VI = 12V to 15V.
n ±15V tracking outputs n Output current to 100 mA n Output voltage balanced to within 2% n Line and load regulation of 0.06% n Internal thermal overload ...
capacitor, CT, is charged by an internal constant-current generator to a predetermined threshold. ... charges and discharges CT as described above. The internal ...
axe-axe / entraxe = E2E) sur le Voltage FR, sans que la géométrie (angle de tube de selle ou de direction) ou la position ... les spécifications suivantes : .... Les vélos SCOTT sont produits selon des procédés de fabrication issus des dernières.
Installation should be carried out in accordance with the latest edition of the ... Caution: Staring into the luminaire at a distance less than 2m can be harmful.
label, installation in an improper working environment or installation not according to the current edition of the National Wiring Regulations. Should this product ...
CONNECTION DIAGRAM AND ORDERING NUMBERS (top view). TO-220 & ... Io = 5 to 1000 mA. 0.5. mA. âId. Quiescent Current Change. Vi = -8 to -25 V. 1.3. mA. âVo ..... SGS-THOMSON Microelectronics GROUP OF COMPANIES. Australia ...
Note 7 In metal can (H) iJ-C is 75 C W and iJ-A is 150 C W In plastic DIP iJ-A is 160 C W In S0-8 iJ-A is .... systems which (a) are intended for surgical implant.
