13 Short in D ... - caphector.com

H01451. Y-B (SB). D+. C4. 14. Airbag Sensor Assembly. 13. C4 D-. Y (SB). 1. 2. Spiral. Cable .... Repair or replace harness or connector be- tween airbag ...
45KB taille 83 téléchargements 429 vues
DI-254 DIAGNOSTICS

-

SUPPLEMENTAL RESTRAINT SYSTEM DI18Q-37

CIRCUIT INSPECTION DTC

B0100/13

Short in D Squib Circuit

CIRCUIT DESCRIPTION The D squib circuit consists of the airbag sensor assembly, spiral cable and steering wheel pad. It causes the airbag to deploy when the airbag deployment conditions are satisfied. For details of the function of each component, see OPERATION on page RS-2 . DTC B0100/13 is recorded when a short is detected in the D squib circuit. DTC No.

B0100/13

DTC Detecting Condition

Trouble Area

 Short circuit between D+ wire harness and D- wire harness of squib  D squib malfunction  Spiral cable malfunction  Airbag sensor assembly malfunction

 Steering wheel pad (D squib)  Spiral cable  Airbag sensor assembly  Wire harness

WIRING DIAGRAM

Airbag Sensor Assembly

A11 D Squib 1

Y-B (SB)

14 C4 D+

2

Y (SB)

13 C4 D-

Spiral Cable

H01451

2002 ECHO (RM884U)

Author:

Date:

424

DI-255 DIAGNOSTICS

-

SUPPLEMENTAL RESTRAINT SYSTEM

INSPECTION PROCEDURE 1

Prepare for inspection. (See step 1 on page DI-390 )

2

Check D squib circuit.

Airbag Sensor Assembly

Spiral Cable D Squib

D-

D+

(-) H01001 H02142

PREPARATION: Release the airbag activation prevention mechanism of the connector (on the airbag sensor assembly side) between the airbag sensor assembly and the spiral cable. (See page DI-239 ) CHECK: For the connector (on the spiral cable side) between the spiral cable and the steering wheel pad, measure the resistance between D+ and D-. OK: Resistance: 1 MΩ or Higher

(+) H02193

NG

Go to step 5.

OK

2002 ECHO (RM884U)

Author:

Date:

425

DI-256 DIAGNOSTICS

3

-

SUPPLEMENTAL RESTRAINT SYSTEM

Check airbag sensor assembly.

Airbag Sensor Assembly

Spiral Cable D Squib →← ON

DTC B0100/13

DLC3

CG H01002 AB0119 H10600

Tc

FI1390

PREPARATION: (a) Connect the connector to the airbag sensor assembly. (b) Connect negative (-) terminal cable to the battery, and wait at least for 2 seconds. CHECK: (a) Turn the ignition switch to ON and wait at least for 20 seconds. (b) Clear DTC stored in memory. (See page DI-239 ) (c) Turn the ignition switch to LOCK, and wait at least for 20 seconds. (d) Turn the ignition switch to ON, and wait at least for 20 seconds. (e) Check DTC. (See page DI-239 ) OK: DTC B0100/13 is not output. HINT: Codes other than code B0100/13 may be output at this time, but they are not relevant to this check.

H10598

NG

Replace airbag sensor assembly.

OK

2002 ECHO (RM884U)

Author:

Date:

426

DI-257 DIAGNOSTICS

4

-

SUPPLEMENTAL RESTRAINT SYSTEM

Check D squib.

→← Spiral Cable D Squib

Airbag Sensor Assembly

ON

DLC3

CG

DTC B0100/13

Tc

H01003 AB0119 H10600 FI1390

H10599

PREPARATION: (a) Turn the ignition switch to LOCK. (b) Disconnect negative (-) terminal cable from the battery, and wait at least for 90 seconds. (c) Connect the steering wheel pad connector. (d) Connect negative (-) terminal cable to the battery, and wait at least for 2 seconds. CHECK: (a) Turn the ignition switch to LOCK, and wait at least for 20 seconds. (b) Turn the ignition switch to ON, and wait at least for 20 seconds. (c) Clear DTC stored in memory. (See page DI-239 ) (d) Turn the ignition switch to LOCK, and wait at least for 20 seconds. (e) Turn the ignition switch to ON, and wait at least for 20 seconds. (f) Check DTC. (See page DI-239 ) OK: DTC B0100/13 is not output. HINT: Codes other than code B0100/13 may be output at this time, but they are not relevant to this check. NG

Replace steering wheel pad.

OK

From the results of the above inspection, the malfunctioning part can now be considered normal. To make sure of this, use the simulation method to check.

2002 ECHO (RM884U)

Author:

Date:

427

DI-258 DIAGNOSTICS

5

-

SUPPLEMENTAL RESTRAINT SYSTEM

Check spiral cable.

Airbag Sensor Assembly

Spiral Cable ←→

D Squib

D-

D+

(-)

PREPARATION: (a) Disconnect the connector between the airbag sensor assembly and the spiral cable. (b) Release the airbag activation prevention mechanism of the spiral cable connector on the airbag sensor assembly side. (See page DI-239 ) CHECK: For the connector (on the spiral cable side) between the spiral cable and the steering wheel pad, measure the resistance between D+ and D-. OK: Resistance: 1 MΩ or Higher

(+)

H01000 H02142

H02195

NG

Repair or replace spiral cable.

OK

6

Check harness between airbag sensor assembly and spiral cable. PREPARATION: Release the airbag activation prevention mechanism of the connector (on the airbag sensor assembly side) between the airbag sensor assembly and the spiral cable. (See page DI-239 ) CHECK: For the connector (on the spiral cable side) between the airbag sensor assembly and the spiral cable, measure the resistance between D+ and D-. OK: Resistance: 1 MΩ or Higher

Airbag Sensor Assembly

Spiral Cable D Squib

D(-) H01004 H02142

D+ (+) H10601

NG

Repair or replace harness or connector between airbag sensor assembly and spiral cable.

OK

From the results of the above inspection, the malfunctioning part can now be considered normal. To make sure of this, use the simulation method to check. 2002 ECHO (RM884U)

Author:

Date:

428