1) Turn off power. 2) Remove outlet box screws from ...
Clear, Brown, Gold or Black without tracer. Clear, Brown, Gold or Black with tracer. Insulated wire (other than green) with copper conductor. Insulated wire (other ...
INSTRUCTIONS For Assembling and Installing Fixtures in Canada Pour L’assemblage et L’installation Au Canada
OUTLET BOX BOITE DE JONCTION
LOCKWASHER RONDELLE FREIN
MOUNTING BAR BARRE DE MONTAGE
19MM (3/4”) SCREW VIS DE 19MM (3/4”)
FIXTURE ARMATURE
16MM (5/8”) SCREW VIS DE 16MM (5/8”)
1) 2) 3)
Turn off power. Remove outlet box screws from outlet box. Use 19mm 3/4” screws to assemble mounting bar to outlet box. Make wire connections (connectors not provided.) Reference chart below for correct connections and wire accordingly. Connect Black or Red Supply Wire to:
Connect White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer
Clear, Brown, Gold or Black with tracer
Insulated wire (other than green) with copper conductor
Insulated wire (other than green) with silver conductor
*Note: When parallel wires (SPT I & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
4)
1) 2)
3)
Connecter le fil noir ou rouge de la boite
Connecter le fil blanc de la boîte
A Noir
A Blanc
*Au cordon parallèle (rond et lisse) *Au cordon parallele (à angles droits el strié) Au bransparent, doré, marron, ou noir sans fil distinctif
Au transparent, doré, marron, ou noir avec un til distinctif
Fil isolé (sauf fil vert) avec conducteur en cuivre
Fil isolé (sauf fil vert) avec conducteur en argent
*Remarque: Avec emploi d’un fil paralléle (SPT I et SPT II). Le fil neutre est á angles droits ou strié et l’autre fil doit étre rond ou lisse (Voir le schéma).
Neutral Wire
Assemble fixture to mounting bar using lockwashers and 16mm (5/8”) screws. 4)
Date Issued: 8/12/94
Coupez l’alimentation secteur. Retirez les vis de boite de jonction de la boite de jonction. Utilisez des vis de 19mm (3/4”) pour assembler la barre de montage à la boite de jonction. Faire les branchements (les serre-fils ne sont pas fournis). Se reporter au tableau ci-dessous pour effectuer les branchements et le câblage.
Fil Neutre
Montez l’armature sur la barre de montage en utilisant une rondelle frein et des vis de 16mm (5/8”). IS-9234-CB
instalar el bloque de terminales para subalimentación. 2. Observe la Fig. 1 e instale el bloque de terminales en el ensamble interior. (UbÃquelo en la posición ...
Place the main power switch in the âOFFâ position. b) Unscrew the fuse(s), or switch âOFFâ the circuit breaker switch(s), that control the power to the fixture or ...
up to (3) #10â12 wires. Multiple wires in a single hole must be of the same size and material. Wire torque: Small #14â10 AWG 20 lb-in. Holes: #8 AWG. 25 lb-in.
SET FLOOR. Set the floor minimum temperature. Available when an auxiliary floor sensor is connected and the built-in room temperature sensor is on. TYPE. Device Type number. ... AUXILIARY SENSOR. Select the type of auxiliary sensor. ... Suggested set
552_Q - 02/14. 2. A Watts Water Technologies Company. 4. Switch Settings. 5. Wiring. Switch Position Action. 1. ON. LOCK Access level adjustment is not available. OFF. UNLOCK Access level adjustment is available. tNt 552. One Stage Heat. Mmm YYYY. Lo
Select if the built-in room temperature sensor is on or off. Room ... Paramètres critiques ... Sélectionnez si le capteur intégré de la température ambiante.
Occasionally there is a screw that is difficult to unscrew. Recently I had a need to remove the half forks on my Glasair. The AN structural screws were connected ...
Furthermore, Cost-Benefit Analyses are believed to become integral to the preparation of a ..... Within the limitations of the project, the only way to calculate figures on a European scale was by .... Human, static overloading measurements ...
ultimately leads to an increase in maintenance costs and/or a decrease in .... Total weight overloading â the total weight of the truck is beyond the legal total weight .... targeted enforcement scenarios can be compared, i.e. Manual selection, ...
UTILISATIONS. Cette boîte satisfait aux exigences des enveloppes de types 1, 3R et pour endroits humides et mouillés seulement lorsque fermée par un couvercle de type 3R ou pour endroits humides et mouillés. RENSEIGNEMENTS GÉNÉRAUX. 1. AVIS - Doit êt
Read Online Now lexmark e450dn remove paper from standard output bin ... Historique Du Chan Et Du Zen Traversles Vies Et Les Enseignements De Ses Plus ...
A) A drop of oil fell on the heating coil during the manufacturing process. It will quickly evaporate and should not occur again. A) Ensure room in which heater is situated is well ventilated. B) Check & ensure there are no combustible materials with
IF YOU HAVE SELF-TAPPING Phillips head sheet metal screws to install, this is a scheme I discovered that saved me a lot of frustration with stripped-out screw ...